diff mbox

[v5,4/4] ARM: dts: sun8i: Add Orange Pi Plus support

Message ID 1449264283-25360-5-git-send-email-jenskuske@gmail.com (mailing list archive)
State New, archived
Headers show

Commit Message

Jens Kuske Dec. 4, 2015, 9:24 p.m. UTC
The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 arch/arm/boot/dts/Makefile                   |  3 +-
 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 77 ++++++++++++++++++++++++++++
 2 files changed, 79 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts

Comments

Maxime Ripard Dec. 8, 2015, 8:33 a.m. UTC | #1
On Fri, Dec 04, 2015 at 10:24:43PM +0100, Jens Kuske wrote:
> The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
> with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
> a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
> WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
> and a 40-pin GPIO header.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>

Applied, thanks!
Maxime
diff mbox

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8f44c7..cc7309b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -661,7 +661,8 @@  dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a33-ga10h-v1.1.dtb \
 	sun8i-a33-ippo-q8h-v1.2.dtb \
 	sun8i-a33-q8-tablet.dtb \
-	sun8i-a33-sinlinx-sina33.dtb
+	sun8i-a33-sinlinx-sina33.dtb \
+	sun8i-h3-orangepi-plus.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
new file mode 100644
index 0000000..e67df59
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -0,0 +1,77 @@ 
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Xunlong Orange Pi Plus";
+	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};