diff mbox

[v3,2/3] Documentation: gpio: Update description for X-Gene standby GPIO controller DTS binding

Message ID 1452162428-26839-3-git-send-email-qnguyen@apm.com (mailing list archive)
State New, archived
Headers show

Commit Message

Quan Nguyen Jan. 7, 2016, 10:27 a.m. UTC 
Update description for X-Gene standby GPIO controller DTS binding to
support GPIO line configuration as input, output or external IRQ pin.

Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
---
 .../devicetree/bindings/gpio/gpio-xgene-sb.txt     | 49 +++++++++++++++++-----
 1 file changed, 38 insertions(+), 11 deletions(-)

Comments

Rob Herring (Arm) Jan. 9, 2016, 10:28 p.m. UTC | #1 
On Thu, Jan 07, 2016 at 05:27:07PM +0700, Quan Nguyen wrote:
> Update description for X-Gene standby GPIO controller DTS binding to
> support GPIO line configuration as input, output or external IRQ pin.
> 
> Signed-off-by: Y Vo <yvo@apm.com>
> Signed-off-by: Quan Nguyen <qnguyen@apm.com>
> ---
>  .../devicetree/bindings/gpio/gpio-xgene-sb.txt     | 49 +++++++++++++++++-----
>  1 file changed, 38 insertions(+), 11 deletions(-)

Acked-by: Rob Herring <robh@kernel.org>
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
index dae1300..a960d1b 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
@@ -1,10 +1,20 @@ 
 APM X-Gene Standby GPIO controller bindings
 
-This is a gpio controller in the standby domain.
-
-There are 20 GPIO pins from 0..21. There is no GPIO_DS14 or GPIO_DS15,
-only GPIO_DS8..GPIO_DS13 support interrupts. The IRQ mapping
-is currently 1-to-1 on interrupts 0x28 thru 0x2d.
+This is a gpio controller in the standby domain. It also supports interrupt in
+some particular pins which are sourced to its parent interrupt controller
+as diagram below:
+                           +-----------------+
+                           | X-Gene standby  |
+                           | GPIO controller +--------- GPIO_0
++------------+             |                 | ...
+| Parent IRQ |             |                 +--------- GPIO_8/EXT_INT_0
+| controller |  EXT_INT_0  |                 | ...
+| (GICv2)    +-------------+                 +--------- GPIO_[N+8]/EXT_INT_N
+|            |  ...        |                 |
+|            |  EXT_INT_N  |                 +--------- GPIO_[N+9]
+|            +-------------+                 | ...
+|            |             |                 +--------- GPIO_MAX
++------------+             +-----------------+
 
 Required properties:
 - compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller
@@ -16,6 +26,11 @@  Required properties:
 		1 = active low
 - gpio-controller: Marks the device node as a GPIO controller.
 - interrupts: Shall contain exactly 6 interrupts.
+- interrupt-parent: Phandle of the parent interrupt controller.
+- interrupt-cells: Shoule be two.
+       - first cell is 0-N coresponding for EXT_INT_0 to EXT_INT_N.
+       - second cell is used to specify flags.
+- interrupt-controller: Marks the device node as an interrupt controller.
 
 Example:
 	sbgpio: sbgpio@17001000 {
@@ -23,10 +38,22 @@  Example:
 		reg = <0x0 0x17001000 0x0 0x400>;
 		#gpio-cells = <2>;
 		gpio-controller;
-		interrupts = 	<0x0 0x28 0x1>,
-				<0x0 0x29 0x1>,
-				<0x0 0x2a 0x1>,
-				<0x0 0x2b 0x1>,
-				<0x0 0x2c 0x1>,
-				<0x0 0x2d 0x1>;
+		interrupt-parent = <&gic>;
+		interrupts =    <0x0 0x28 0x4>,
+				<0x0 0x29 0x4>,
+				<0x0 0x2a 0x4>,
+				<0x0 0x2b 0x4>,
+				<0x0 0x2c 0x4>,
+				<0x0 0x2d 0x4>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	testuser {
+		compatible = "example,testuser";
+		/* Use the GPIO_13/EXT_INT_5 line as an active high triggered
+		 * level interrupt
+		 */
+		interrupts = <5 4>;
+		interrupt-parent = <&sbgpio>;
 	};