diff mbox

[v4,2/6] dt-bindings: ARM: Mediatek: Document bindings for MT2701

Message ID 1453271747-57397-3-git-send-email-jamesjj.liao@mediatek.com (mailing list archive)
State New, archived
Headers show

Commit Message

James Liao Jan. 20, 2016, 6:35 a.m. UTC
This patch adds the binding documentation for apmixedsys, bdpsys,
ethsys, hifsys, imgsys, infracfg, mmsys, pericfg, topckgen and
vdecsys for Mediatek MT2701.

Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Tested-by: John Crispin <blogic@openwrt.org>
---
 .../bindings/arm/mediatek/mediatek,apmixedsys.txt  |  1 +
 .../bindings/arm/mediatek/mediatek,bdpsys.txt      | 22 ++++++++++++++++++++++
 .../bindings/arm/mediatek/mediatek,ethsys.txt      | 22 ++++++++++++++++++++++
 .../bindings/arm/mediatek/mediatek,hifsys.txt      | 22 ++++++++++++++++++++++
 .../bindings/arm/mediatek/mediatek,imgsys.txt      |  1 +
 .../bindings/arm/mediatek/mediatek,infracfg.txt    |  1 +
 .../bindings/arm/mediatek/mediatek,mmsys.txt       |  1 +
 .../bindings/arm/mediatek/mediatek,pericfg.txt     |  1 +
 .../bindings/arm/mediatek/mediatek,topckgen.txt    |  1 +
 .../bindings/arm/mediatek/mediatek,vdecsys.txt     |  1 +
 10 files changed, 73 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
 create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
 create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt

Comments

Rob Herring Jan. 20, 2016, 4:32 p.m. UTC | #1
On Wed, Jan 20, 2016 at 02:35:43PM +0800, James Liao wrote:
> This patch adds the binding documentation for apmixedsys, bdpsys,
> ethsys, hifsys, imgsys, infracfg, mmsys, pericfg, topckgen and
> vdecsys for Mediatek MT2701.
> 
> Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
> Tested-by: John Crispin <blogic@openwrt.org>
> ---
>  .../bindings/arm/mediatek/mediatek,apmixedsys.txt  |  1 +
>  .../bindings/arm/mediatek/mediatek,bdpsys.txt      | 22 ++++++++++++++++++++++
>  .../bindings/arm/mediatek/mediatek,ethsys.txt      | 22 ++++++++++++++++++++++
>  .../bindings/arm/mediatek/mediatek,hifsys.txt      | 22 ++++++++++++++++++++++
>  .../bindings/arm/mediatek/mediatek,imgsys.txt      |  1 +
>  .../bindings/arm/mediatek/mediatek,infracfg.txt    |  1 +
>  .../bindings/arm/mediatek/mediatek,mmsys.txt       |  1 +
>  .../bindings/arm/mediatek/mediatek,pericfg.txt     |  1 +
>  .../bindings/arm/mediatek/mediatek,topckgen.txt    |  1 +
>  .../bindings/arm/mediatek/mediatek,vdecsys.txt     |  1 +
>  10 files changed, 73 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
>  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
>  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
> 
> diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
> index 936166f..a701e19 100644
> --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
> +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
> @@ -6,6 +6,7 @@ The Mediatek apmixedsys controller provides the PLLs to the system.
>  Required Properties:
>  
>  - compatible: Should be:
> +	- "mediatek,mt2701-apmixedsys"
>  	- "mediatek,mt8135-apmixedsys"
>  	- "mediatek,mt8173-apmixedsys"
>  - #clock-cells: Must be 1
> diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
> new file mode 100644
> index 0000000..4137196
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
> @@ -0,0 +1,22 @@
> +Mediatek bdpsys controller
> +============================
> +
> +The Mediatek bdpsys controller provides various clocks to the system.

As you clarified these blocks provide more that just clocks. Please list 
all the functions here and on the others.

> +
> +Required Properties:
> +
> +- compatible: Should be:
> +	- "mediatek,mt2701-bdpsys", "syscon"
> +- #clock-cells: Must be 1
> +
> +The bdpsys controller uses the common clk binding from
> +Documentation/devicetree/bindings/clock/clock-bindings.txt
> +The available clocks are defined in dt-bindings/clock/mt*-clk.h.
> +
James Liao Jan. 21, 2016, 5:18 a.m. UTC | #2
Hi Rob,

On Wed, 2016-01-20 at 10:32 -0600, Rob Herring wrote:
> On Wed, Jan 20, 2016 at 02:35:43PM +0800, James Liao wrote:
> > This patch adds the binding documentation for apmixedsys, bdpsys,
> > ethsys, hifsys, imgsys, infracfg, mmsys, pericfg, topckgen and
> > vdecsys for Mediatek MT2701.
> > 
> > Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
> > Tested-by: John Crispin <blogic@openwrt.org>
> > ---
> >  .../bindings/arm/mediatek/mediatek,apmixedsys.txt  |  1 +
> >  .../bindings/arm/mediatek/mediatek,bdpsys.txt      | 22 ++++++++++++++++++++++
> >  .../bindings/arm/mediatek/mediatek,ethsys.txt      | 22 ++++++++++++++++++++++
> >  .../bindings/arm/mediatek/mediatek,hifsys.txt      | 22 ++++++++++++++++++++++
> >  .../bindings/arm/mediatek/mediatek,imgsys.txt      |  1 +
> >  .../bindings/arm/mediatek/mediatek,infracfg.txt    |  1 +
> >  .../bindings/arm/mediatek/mediatek,mmsys.txt       |  1 +
> >  .../bindings/arm/mediatek/mediatek,pericfg.txt     |  1 +
> >  .../bindings/arm/mediatek/mediatek,topckgen.txt    |  1 +
> >  .../bindings/arm/mediatek/mediatek,vdecsys.txt     |  1 +
> >  10 files changed, 73 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
> >  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
> >  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
> > index 936166f..a701e19 100644
> > --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
> > +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
> > @@ -6,6 +6,7 @@ The Mediatek apmixedsys controller provides the PLLs to the system.
> >  Required Properties:
> >  
> >  - compatible: Should be:
> > +	- "mediatek,mt2701-apmixedsys"
> >  	- "mediatek,mt8135-apmixedsys"
> >  	- "mediatek,mt8173-apmixedsys"
> >  - #clock-cells: Must be 1
> > diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
> > new file mode 100644
> > index 0000000..4137196
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
> > @@ -0,0 +1,22 @@
> > +Mediatek bdpsys controller
> > +============================
> > +
> > +The Mediatek bdpsys controller provides various clocks to the system.
> 
> As you clarified these blocks provide more that just clocks. Please list 
> all the functions here and on the others.

Some blocks may provide clock and reset controller at the same time. But
most of them will not provide functions directly. Instead, some DT
blocks which provide specific functions may refer to these controller
nodes due to it need to access the same register space.

For example, scpsys (the power domain provider) refers to infracfg
because it need to control infracfg registers when power on/off domains:

	scpsys: scpsys@10006000 {
		compatible = "mediatek,mt2701-scpsys";
		#power-domain-cells = <1>;
		reg = <0 0x10006000 0 0x1000>;
		infracfg = <&infracfg>;
	};

So I think it should not need to list all functions for each blocks
here.

> > +
> > +Required Properties:
> > +
> > +- compatible: Should be:
> > +	- "mediatek,mt2701-bdpsys", "syscon"
> > +- #clock-cells: Must be 1
> > +
> > +The bdpsys controller uses the common clk binding from
> > +Documentation/devicetree/bindings/clock/clock-bindings.txt
> > +The available clocks are defined in dt-bindings/clock/mt*-clk.h.
> > +
Rob Herring Feb. 1, 2016, 3:55 p.m. UTC | #3
On Wed, Jan 20, 2016 at 11:18 PM, James Liao <jamesjj.liao@mediatek.com> wrote:
> Hi Rob,
>
> On Wed, 2016-01-20 at 10:32 -0600, Rob Herring wrote:
>> On Wed, Jan 20, 2016 at 02:35:43PM +0800, James Liao wrote:
>> > This patch adds the binding documentation for apmixedsys, bdpsys,
>> > ethsys, hifsys, imgsys, infracfg, mmsys, pericfg, topckgen and
>> > vdecsys for Mediatek MT2701.
>> >
>> > Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
>> > Tested-by: John Crispin <blogic@openwrt.org>
>> > ---
>> >  .../bindings/arm/mediatek/mediatek,apmixedsys.txt  |  1 +
>> >  .../bindings/arm/mediatek/mediatek,bdpsys.txt      | 22 ++++++++++++++++++++++
>> >  .../bindings/arm/mediatek/mediatek,ethsys.txt      | 22 ++++++++++++++++++++++
>> >  .../bindings/arm/mediatek/mediatek,hifsys.txt      | 22 ++++++++++++++++++++++
>> >  .../bindings/arm/mediatek/mediatek,imgsys.txt      |  1 +
>> >  .../bindings/arm/mediatek/mediatek,infracfg.txt    |  1 +
>> >  .../bindings/arm/mediatek/mediatek,mmsys.txt       |  1 +
>> >  .../bindings/arm/mediatek/mediatek,pericfg.txt     |  1 +
>> >  .../bindings/arm/mediatek/mediatek,topckgen.txt    |  1 +
>> >  .../bindings/arm/mediatek/mediatek,vdecsys.txt     |  1 +
>> >  10 files changed, 73 insertions(+)
>> >  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
>> >  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
>> >  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
>> > index 936166f..a701e19 100644
>> > --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
>> > +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
>> > @@ -6,6 +6,7 @@ The Mediatek apmixedsys controller provides the PLLs to the system.
>> >  Required Properties:
>> >
>> >  - compatible: Should be:
>> > +   - "mediatek,mt2701-apmixedsys"
>> >     - "mediatek,mt8135-apmixedsys"
>> >     - "mediatek,mt8173-apmixedsys"
>> >  - #clock-cells: Must be 1
>> > diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
>> > new file mode 100644
>> > index 0000000..4137196
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
>> > @@ -0,0 +1,22 @@
>> > +Mediatek bdpsys controller
>> > +============================
>> > +
>> > +The Mediatek bdpsys controller provides various clocks to the system.
>>
>> As you clarified these blocks provide more that just clocks. Please list
>> all the functions here and on the others.
>
> Some blocks may provide clock and reset controller at the same time. But

Then say the block provides clocks and resets is all I'm asking for.

> most of them will not provide functions directly. Instead, some DT
> blocks which provide specific functions may refer to these controller
> nodes due to it need to access the same register space.
>
> For example, scpsys (the power domain provider) refers to infracfg
> because it need to control infracfg registers when power on/off domains:
>
>         scpsys: scpsys@10006000 {
>                 compatible = "mediatek,mt2701-scpsys";
>                 #power-domain-cells = <1>;
>                 reg = <0 0x10006000 0 0x1000>;
>                 infracfg = <&infracfg>;
>         };
>
> So I think it should not need to list all functions for each blocks
> here.

Sorry, but you do need to describe what functions the blocks provide.

Also, if you are accessing the infracfg regs directly to modify clock
registers outside of the clock driver, that is very bad design. The
clock driver could assume that register values are not changing behind
its back and it bypasses any locks around register accesses. I can see
why it is needed though, but we really need a proper interface.

Rob
Matthias Brugger Feb. 1, 2016, 6:01 p.m. UTC | #4
On 01/02/16 16:55, Rob Herring wrote:
> On Wed, Jan 20, 2016 at 11:18 PM, James Liao <jamesjj.liao@mediatek.com> wrote:
>> Hi Rob,
>>
>> On Wed, 2016-01-20 at 10:32 -0600, Rob Herring wrote:
>>> On Wed, Jan 20, 2016 at 02:35:43PM +0800, James Liao wrote:
>>>> This patch adds the binding documentation for apmixedsys, bdpsys,
>>>> ethsys, hifsys, imgsys, infracfg, mmsys, pericfg, topckgen and
>>>> vdecsys for Mediatek MT2701.
>>>>
>>>> Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
>>>> Tested-by: John Crispin <blogic@openwrt.org>
>>>> ---
>>>>   .../bindings/arm/mediatek/mediatek,apmixedsys.txt  |  1 +
>>>>   .../bindings/arm/mediatek/mediatek,bdpsys.txt      | 22 ++++++++++++++++++++++
>>>>   .../bindings/arm/mediatek/mediatek,ethsys.txt      | 22 ++++++++++++++++++++++
>>>>   .../bindings/arm/mediatek/mediatek,hifsys.txt      | 22 ++++++++++++++++++++++
>>>>   .../bindings/arm/mediatek/mediatek,imgsys.txt      |  1 +
>>>>   .../bindings/arm/mediatek/mediatek,infracfg.txt    |  1 +
>>>>   .../bindings/arm/mediatek/mediatek,mmsys.txt       |  1 +
>>>>   .../bindings/arm/mediatek/mediatek,pericfg.txt     |  1 +
>>>>   .../bindings/arm/mediatek/mediatek,topckgen.txt    |  1 +
>>>>   .../bindings/arm/mediatek/mediatek,vdecsys.txt     |  1 +
>>>>   10 files changed, 73 insertions(+)
>>>>   create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
>>>>   create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
>>>>   create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
>>>> index 936166f..a701e19 100644
>>>> --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
>>>> +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
>>>> @@ -6,6 +6,7 @@ The Mediatek apmixedsys controller provides the PLLs to the system.
>>>>   Required Properties:
>>>>
>>>>   - compatible: Should be:
>>>> +   - "mediatek,mt2701-apmixedsys"
>>>>      - "mediatek,mt8135-apmixedsys"
>>>>      - "mediatek,mt8173-apmixedsys"
>>>>   - #clock-cells: Must be 1
>>>> diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
>>>> new file mode 100644
>>>> index 0000000..4137196
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
>>>> @@ -0,0 +1,22 @@
>>>> +Mediatek bdpsys controller
>>>> +============================
>>>> +
>>>> +The Mediatek bdpsys controller provides various clocks to the system.
>>>
>>> As you clarified these blocks provide more that just clocks. Please list
>>> all the functions here and on the others.
>>
>> Some blocks may provide clock and reset controller at the same time. But
>
> Then say the block provides clocks and resets is all I'm asking for.
>
>> most of them will not provide functions directly. Instead, some DT
>> blocks which provide specific functions may refer to these controller
>> nodes due to it need to access the same register space.
>>
>> For example, scpsys (the power domain provider) refers to infracfg
>> because it need to control infracfg registers when power on/off domains:
>>
>>          scpsys: scpsys@10006000 {
>>                  compatible = "mediatek,mt2701-scpsys";
>>                  #power-domain-cells = <1>;
>>                  reg = <0 0x10006000 0 0x1000>;
>>                  infracfg = <&infracfg>;
>>          };
>>
>> So I think it should not need to list all functions for each blocks
>> here.
>
> Sorry, but you do need to describe what functions the blocks provide.
>
> Also, if you are accessing the infracfg regs directly to modify clock
> registers outside of the clock driver, that is very bad design. The
> clock driver could assume that register values are not changing behind
> its back and it bypasses any locks around register accesses. I can see
> why it is needed though, but we really need a proper interface.
>

Some of the register blocks like infracfg is a potpourri of different 
functions. Clocks and power domains are some of them. In the drivers 
this is isolated, but there are many blocks which are not used at the 
moment and therefor are not documented in bindings description (e.g. 
debug control for the very same block, not sure if that will be 
implemented one day).

Would it be ok for you, if James just lists the blocks which already 
have an implementation and leaving apart the rest of it?

Regards,
Matthias
James Liao Feb. 2, 2016, 8:07 a.m. UTC | #5
Hi Rob,

On Mon, 2016-02-01 at 09:55 -0600, Rob Herring wrote:
> On Wed, Jan 20, 2016 at 11:18 PM, James Liao <jamesjj.liao@mediatek.com> wrote:
> > On Wed, 2016-01-20 at 10:32 -0600, Rob Herring wrote:
> >> On Wed, Jan 20, 2016 at 02:35:43PM +0800, James Liao wrote:
> >> > This patch adds the binding documentation for apmixedsys, bdpsys,
> >> > ethsys, hifsys, imgsys, infracfg, mmsys, pericfg, topckgen and
> >> > vdecsys for Mediatek MT2701.
> >> >
> >> > Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
> >> > Tested-by: John Crispin <blogic@openwrt.org>
> >> > ---
> >> >  .../bindings/arm/mediatek/mediatek,apmixedsys.txt  |  1 +
> >> >  .../bindings/arm/mediatek/mediatek,bdpsys.txt      | 22 ++++++++++++++++++++++
> >> >  .../bindings/arm/mediatek/mediatek,ethsys.txt      | 22 ++++++++++++++++++++++
> >> >  .../bindings/arm/mediatek/mediatek,hifsys.txt      | 22 ++++++++++++++++++++++
> >> >  .../bindings/arm/mediatek/mediatek,imgsys.txt      |  1 +
> >> >  .../bindings/arm/mediatek/mediatek,infracfg.txt    |  1 +
> >> >  .../bindings/arm/mediatek/mediatek,mmsys.txt       |  1 +
> >> >  .../bindings/arm/mediatek/mediatek,pericfg.txt     |  1 +
> >> >  .../bindings/arm/mediatek/mediatek,topckgen.txt    |  1 +
> >> >  .../bindings/arm/mediatek/mediatek,vdecsys.txt     |  1 +
> >> >  10 files changed, 73 insertions(+)
> >> >  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
> >> >  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
> >> >  create mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
> >> >
> >> > diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
> >> > index 936166f..a701e19 100644
> >> > --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
> >> > +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
> >> > @@ -6,6 +6,7 @@ The Mediatek apmixedsys controller provides the PLLs to the system.
> >> >  Required Properties:
> >> >
> >> >  - compatible: Should be:
> >> > +   - "mediatek,mt2701-apmixedsys"
> >> >     - "mediatek,mt8135-apmixedsys"
> >> >     - "mediatek,mt8173-apmixedsys"
> >> >  - #clock-cells: Must be 1
> >> > diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
> >> > new file mode 100644
> >> > index 0000000..4137196
> >> > --- /dev/null
> >> > +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
> >> > @@ -0,0 +1,22 @@
> >> > +Mediatek bdpsys controller
> >> > +============================
> >> > +
> >> > +The Mediatek bdpsys controller provides various clocks to the system.
> >>
> >> As you clarified these blocks provide more that just clocks. Please list
> >> all the functions here and on the others.
> >
> > Some blocks may provide clock and reset controller at the same time. But
> 
> Then say the block provides clocks and resets is all I'm asking for.

infracfg and pericfg had mentioned they would provide clock and reset
controllers. I'll add the same description into hifsys.

> > most of them will not provide functions directly. Instead, some DT
> > blocks which provide specific functions may refer to these controller
> > nodes due to it need to access the same register space.
> >
> > For example, scpsys (the power domain provider) refers to infracfg
> > because it need to control infracfg registers when power on/off domains:
> >
> >         scpsys: scpsys@10006000 {
> >                 compatible = "mediatek,mt2701-scpsys";
> >                 #power-domain-cells = <1>;
> >                 reg = <0 0x10006000 0 0x1000>;
> >                 infracfg = <&infracfg>;
> >         };
> >
> > So I think it should not need to list all functions for each blocks
> > here.
> 
> Sorry, but you do need to describe what functions the blocks provide.

infracfg for example, this DT node provides only clock and reset
controllers.

	infracfg: power-controller@10001000 {
		compatible = "mediatek,mt2701-infracfg", "syscon";
		reg = <0 0x10001000 0 0x1000>;
		#clock-cells = <1>;
		#reset-cells = <1>;
	};

It mapped register space 0x10001000 ~ 0x10001fff. The clock and reset
controllers only use partial registers in this space. Some other
functions, such as bus protection and DCM, use registers in 0x10001000 ~
0x10001fff. But these functions are not provided by this node. Instead,
these function may be implemented by other nodes, such as scpsys. That's
why we only list clock and reset controllers in infracfg document.

> Also, if you are accessing the infracfg regs directly to modify clock
> registers outside of the clock driver, that is very bad design. The
> clock driver could assume that register values are not changing behind
> its back and it bypasses any locks around register accesses. I can see
> why it is needed though, but we really need a proper interface.

No, we won't modify clock registers directly outside of clock driver.
All drivers that need to control clocks must use standard CCF APIs to
lookup and operate clocks.

Scpsys for example, it need to enable/disable clocks and bus protections
when power domain on/off. Scpsys will control clocks through CCF, and
control bus protections through regmap to access infracfg's registers.
Of course, the registers of clocks and bus protection are different.

	scpsys: scpsys@10006000 {
		compatible = "mediatek,mt8173-scpsys";
		#power-domain-cells = <1>;
		reg = <0 0x10006000 0 0x1000>;
		clocks = <&clk26m>,
			 <&topckgen CLK_TOP_MM_SEL>,
			 <&topckgen CLK_TOP_VENC_SEL>,
			 <&topckgen CLK_TOP_VENC_LT_SEL>;
		clock-names = "mfg", "mm", "venc", "venc_lt";
		infracfg = <&infracfg>;
	};

Here is MT8173's scpsys DT node. And you can see it refers clocks
provided by topckeng, and infracfg register space.


Best regards,

James
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
index 936166f..a701e19 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
@@ -6,6 +6,7 @@  The Mediatek apmixedsys controller provides the PLLs to the system.
 Required Properties:
 
 - compatible: Should be:
+	- "mediatek,mt2701-apmixedsys"
 	- "mediatek,mt8135-apmixedsys"
 	- "mediatek,mt8173-apmixedsys"
 - #clock-cells: Must be 1
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
new file mode 100644
index 0000000..4137196
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
@@ -0,0 +1,22 @@ 
+Mediatek bdpsys controller
+============================
+
+The Mediatek bdpsys controller provides various clocks to the system.
+
+Required Properties:
+
+- compatible: Should be:
+	- "mediatek,mt2701-bdpsys", "syscon"
+- #clock-cells: Must be 1
+
+The bdpsys controller uses the common clk binding from
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+The available clocks are defined in dt-bindings/clock/mt*-clk.h.
+
+Example:
+
+bdpsys: clock-controller@1c000000 {
+	compatible = "mediatek,mt2701-bdpsys", "syscon";
+	reg = <0 0x1c000000 0 0x1000>;
+	#clock-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
new file mode 100644
index 0000000..768f3a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
@@ -0,0 +1,22 @@ 
+Mediatek ethsys controller
+============================
+
+The Mediatek ethsys controller provides various clocks to the system.
+
+Required Properties:
+
+- compatible: Should be:
+	- "mediatek,mt2701-ethsys", "syscon"
+- #clock-cells: Must be 1
+
+The ethsys controller uses the common clk binding from
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+The available clocks are defined in dt-bindings/clock/mt*-clk.h.
+
+Example:
+
+ethsys: clock-controller@1b000000 {
+	compatible = "mediatek,mt2701-ethsys", "syscon";
+	reg = <0 0x1b000000 0 0x1000>;
+	#clock-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
new file mode 100644
index 0000000..b7a39b6
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
@@ -0,0 +1,22 @@ 
+Mediatek hifsys controller
+============================
+
+The Mediatek hifsys controller provides various clocks to the system.
+
+Required Properties:
+
+- compatible: Should be:
+	- "mediatek,mt2701-hifsys", "syscon"
+- #clock-cells: Must be 1
+
+The hifsys controller uses the common clk binding from
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+The available clocks are defined in dt-bindings/clock/mt*-clk.h.
+
+Example:
+
+hifsys: clock-controller@1a000000 {
+	compatible = "mediatek,mt2701-hifsys", "syscon";
+	reg = <0 0x1a000000 0 0x1000>;
+	#clock-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt
index b1f2ce1..9bda7f7 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt
@@ -6,6 +6,7 @@  The Mediatek imgsys controller provides various clocks to the system.
 Required Properties:
 
 - compatible: Should be:
+	- "mediatek,mt2701-imgsys", "syscon"
 	- "mediatek,mt8173-imgsys", "syscon"
 - #clock-cells: Must be 1
 
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt
index f6cd3e4..2f11a69 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt
@@ -7,6 +7,7 @@  outputs to the system.
 Required Properties:
 
 - compatible: Should be:
+	- "mediatek,mt2701-infracfg", "syscon"
 	- "mediatek,mt8135-infracfg", "syscon"
 	- "mediatek,mt8173-infracfg", "syscon"
 - #clock-cells: Must be 1
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt
index 4385946..c9d9d43 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt
@@ -6,6 +6,7 @@  The Mediatek mmsys controller provides various clocks to the system.
 Required Properties:
 
 - compatible: Should be:
+	- "mediatek,mt2701-mmsys", "syscon"
 	- "mediatek,mt8173-mmsys", "syscon"
 - #clock-cells: Must be 1
 
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt
index f25b854..d3454cd 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt
@@ -7,6 +7,7 @@  outputs to the system.
 Required Properties:
 
 - compatible: Should be:
+	- "mediatek,mt2701-pericfg", "syscon"
 	- "mediatek,mt8135-pericfg", "syscon"
 	- "mediatek,mt8173-pericfg", "syscon"
 - #clock-cells: Must be 1
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt
index f9e9179..602e5bc 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt
@@ -6,6 +6,7 @@  The Mediatek topckgen controller provides various clocks to the system.
 Required Properties:
 
 - compatible: Should be:
+	- "mediatek,mt2701-topckgen"
 	- "mediatek,mt8135-topckgen"
 	- "mediatek,mt8173-topckgen"
 - #clock-cells: Must be 1
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt
index 1faacf1..f5b1e7d 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt
@@ -6,6 +6,7 @@  The Mediatek vdecsys controller provides various clocks to the system.
 Required Properties:
 
 - compatible: Should be:
+	- "mediatek,mt2701-vdecsys", "syscon"
 	- "mediatek,mt8173-vdecsys", "syscon"
 - #clock-cells: Must be 1