[2/5] dt-binding:Rename the mbigen binding file name

Commit Message

majun (F) Feb. 14, 2016, 2:16 a.m. UTC

From: Ma Jun <[e-mail]>

Because added the mbigen-v1 compatible string, the origin name is
not suitable any more. So,I remove the version number from file name.

Signed-off-by: Ma Jun <[e-mail]>
---
 .../interrupt-controller/hisilicon,mbigen-v2.txt   |   74 --------------------
 .../interrupt-controller/hisilicon,mbigen.txt      |   74 ++++++++++++++++++++
 2 files changed, 74 insertions(+), 74 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen.txt

Patch

diff --git a/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt b/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt
deleted file mode 100644
index bdd1dea..0000000
--- a/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt
+++ /dev/null
@@ -1,74 +0,0 @@ 
-Hisilicon mbigen device tree bindings.
-=======================================
-
-Mbigen means: message based interrupt generator.
-
-MBI is kind of msi interrupt only used on Non-PCI devices.
-
-To reduce the wired interrupt number connected to GIC,
-Hisilicon designed mbigen to collect and generate interrupt.
-
-
-Non-pci devices can connect to mbigen and generate the
-interrupt by writing ITS register.
-
-The mbigen chip and devices connect to mbigen have the following properties:
-
-Mbigen main node required properties:
--------------------------------------------
-- compatible: Should be "hisilicon,mbigen-v2" or "hisilicon,mbigen-v1"
-
-- reg: Specifies the base physical address and size of the Mbigen
-  registers.
-
-- interrupt controller: Identifies the node as an interrupt controller
-
-- msi-parent: Specifies the MSI controller this mbigen use.
-  For more detail information,please refer to the generic msi-parent binding in
-  Documentation/devicetree/bindings/interrupt-controller/msi.txt.
-
-- num-pins: the total number of pins implemented in this Mbigen
-  instance.
-
-- #interrupt-cells : Specifies the number of cells needed to encode an
-  interrupt source. The value must be 2.
-
-  The 1st cell is hardware pin number of the interrupt.This number is local to
-  each mbigen chip and in the range from 0 to the maximum interrupts number
-  of the mbigen.
-
-  The 2nd cell is the interrupt trigger type.
-	The value of this cell should be:
-	1: rising edge triggered
-	or
-	4: high level triggered
-
-Examples:
-
-	mbigen_device_gmac:intc {
-			compatible = "hisilicon,mbigen-v2";
-			reg = <0x0 0xc0080000 0x0 0x10000>;
-			interrupt-controller;
-			msi-parent = <&its_dsa 0x40b1c>;
-			num-pins = <9>;
-			#interrupt-cells = <2>;
-	};
-
-Devices connect to mbigen required properties:
-----------------------------------------------------
--interrupt-parent: Specifies the mbigen device node which device connected.
-
--interrupts:Specifies the interrupt source.
- For the specific information of each cell in this property,please refer to
- the "interrupt-cells" description mentioned above.
-
-Examples:
-	gmac0: ethernet@c2080000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0 0xc2080000 0 0x20000>,
-		      <0 0xc0000000 0 0x1000>;
-		interrupt-parent  = <&mbigen_device_gmac>;
-		interrupts =	<656 1>,
-				<657 1>;
-	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen.txt b/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen.txt
new file mode 100644
index 0000000..bdd1dea
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen.txt
@@ -0,0 +1,74 @@ 
+Hisilicon mbigen device tree bindings.
+=======================================
+
+Mbigen means: message based interrupt generator.
+
+MBI is kind of msi interrupt only used on Non-PCI devices.
+
+To reduce the wired interrupt number connected to GIC,
+Hisilicon designed mbigen to collect and generate interrupt.
+
+
+Non-pci devices can connect to mbigen and generate the
+interrupt by writing ITS register.
+
+The mbigen chip and devices connect to mbigen have the following properties:
+
+Mbigen main node required properties:
+-------------------------------------------
+- compatible: Should be "hisilicon,mbigen-v2" or "hisilicon,mbigen-v1"
+
+- reg: Specifies the base physical address and size of the Mbigen
+  registers.
+
+- interrupt controller: Identifies the node as an interrupt controller
+
+- msi-parent: Specifies the MSI controller this mbigen use.
+  For more detail information,please refer to the generic msi-parent binding in
+  Documentation/devicetree/bindings/interrupt-controller/msi.txt.
+
+- num-pins: the total number of pins implemented in this Mbigen
+  instance.
+
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value must be 2.
+
+  The 1st cell is hardware pin number of the interrupt.This number is local to
+  each mbigen chip and in the range from 0 to the maximum interrupts number
+  of the mbigen.
+
+  The 2nd cell is the interrupt trigger type.
+	The value of this cell should be:
+	1: rising edge triggered
+	or
+	4: high level triggered
+
+Examples:
+
+	mbigen_device_gmac:intc {
+			compatible = "hisilicon,mbigen-v2";
+			reg = <0x0 0xc0080000 0x0 0x10000>;
+			interrupt-controller;
+			msi-parent = <&its_dsa 0x40b1c>;
+			num-pins = <9>;
+			#interrupt-cells = <2>;
+	};
+
+Devices connect to mbigen required properties:
+----------------------------------------------------
+-interrupt-parent: Specifies the mbigen device node which device connected.
+
+-interrupts:Specifies the interrupt source.
+ For the specific information of each cell in this property,please refer to
+ the "interrupt-cells" description mentioned above.
+
+Examples:
+	gmac0: ethernet@c2080000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0 0xc2080000 0 0x20000>,
+		      <0 0xc0000000 0 0x1000>;
+		interrupt-parent  = <&mbigen_device_gmac>;
+		interrupts =	<656 1>,
+				<657 1>;
+	};