@@ -21,7 +21,7 @@
#include <linux/slab.h>
#include <linux/time.h>
-#define STI_DS_REG(ch) (4 * (ch)) /* Channel's Duty Cycle register */
+#define STI_DS_REG(ch) (4 * (ch)) /* Device's Duty Cycle register */
#define STI_PWMCR 0x50 /* Control/Config register */
#define STI_INTEN 0x54 /* Interrupt Enable/Disable register */
#define PWM_PRESCALE_LOW_MASK 0x0f
@@ -40,7 +40,7 @@ enum {
struct sti_pwm_compat_data {
const struct reg_field *reg_fields;
- unsigned int num_chan;
+ unsigned int num_devs;
unsigned int max_pwm_cnt;
unsigned int max_prescale;
};
@@ -130,13 +130,13 @@ static int sti_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
/* Allow configuration changes if one of the
* following conditions satisfy.
- * 1. No channels have been configured.
- * 2. Only one channel has been configured and the new request
- * is for the same channel.
- * 3. Only one channel has been configured and the new request is
- * for a new channel and period of the new channel is same as
+ * 1. No devices have been configured.
+ * 2. Only one device has been configured and the new request
+ * is for the same device.
+ * 3. Only one device has been configured and the new request is
+ * for a new device and period of the new device is same as
* the current configured period.
- * 4. More than one channels are configured and period of the new
+ * 4. More than one devices are configured and period of the new
* requestis the same as the current period.
*/
if (!ncfg ||
@@ -201,7 +201,7 @@ static int sti_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
int ret = 0;
/*
- * Since we have a common enable for all PWM channels,
+ * Since we have a common enable for all PWM devices,
* do not enable if already enabled.
*/
mutex_lock(&pc->sti_pwm_lock);
@@ -259,11 +259,11 @@ static int sti_pwm_probe_dt(struct sti_pwm_chip *pc)
const struct reg_field *reg_fields;
struct device_node *np = dev->of_node;
struct sti_pwm_compat_data *cdata = pc->cdata;
- u32 num_chan;
+ u32 num_devs;
- of_property_read_u32(np, "st,pwm-num-chan", &num_chan);
- if (num_chan)
- cdata->num_chan = num_chan;
+ of_property_read_u32(np, "st,pwm-num-devs", &num_devs);
+ if (num_devs)
+ cdata->num_devs = num_devs;
reg_fields = cdata->reg_fields;
@@ -330,7 +330,7 @@ static int sti_pwm_probe(struct platform_device *pdev)
cdata->reg_fields = &sti_pwm_regfields[0];
cdata->max_prescale = 0xff;
cdata->max_pwm_cnt = 255;
- cdata->num_chan = 1;
+ cdata->num_devs = 1;
pc->cdata = cdata;
pc->dev = dev;
@@ -362,7 +362,7 @@ static int sti_pwm_probe(struct platform_device *pdev)
pc->chip.dev = dev;
pc->chip.ops = &sti_pwm_ops;
pc->chip.base = -1;
- pc->chip.npwm = pc->cdata->num_chan;
+ pc->chip.npwm = pc->cdata->num_devs;
pc->chip.can_sleep = true;
ret = pwmchip_add(&pc->chip);
@@ -381,7 +381,7 @@ static int sti_pwm_remove(struct platform_device *pdev)
struct sti_pwm_chip *pc = platform_get_drvdata(pdev);
unsigned int i;
- for (i = 0; i < pc->cdata->num_chan; i++)
+ for (i = 0; i < pc->cdata->num_devs; i++)
pwm_disable(&pc->chip.pwms[i]);
clk_unprepare(pc->clk);
This is to bring the terminology used in the STi PWM driver more into line with the PWM subsystem. Signed-off-by: Lee Jones <lee.jones@linaro.org> --- drivers/pwm/pwm-sti.c | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-)