new file mode 100644
@@ -0,0 +1,21 @@
+* QCOM SoC Temperature Sensor (TSENS)
+
+Required properties:
+- compatible :
+ - "qcom,msm8916-tsens" : For 8916 Family of SoCs
+ - "qcom,msm8974-tsens" : For 8974 Family of SoCs
+ - "qcom,msm8996-tsens" : For 8996 Family of SoCs
+
+- reg: Address range of the thermal registers
+- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
+- Refer to Documentation/devicetree/bindings/nvmem/nvmem.txt to know how to specify
+nvmem cells
+
+Example:
+tsens: thermal-sensor@900000 {
+ compatible = "qcom,msm8916-tsens";
+ reg = <0x4a8000 0x2000>;
+ nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
+ nvmem-cell-names = "caldata", "calsel";
+ #thermal-sensor-cells = <1>;
+ };
@@ -410,4 +410,9 @@ config QCOM_SPMI_TEMP_ALARM
real time die temperature if an ADC is present or an estimate of the
temperature based upon the over temperature stage value.
+menu "Qualcomm thermal drivers"
+depends on (ARCH_QCOM && OF) || COMPILE_TEST
+source "drivers/thermal/qcom/Kconfig"
+endmenu
+
endif
@@ -46,6 +46,7 @@ obj-$(CONFIG_TI_SOC_THERMAL) += ti-soc-thermal/
obj-$(CONFIG_INT340X_THERMAL) += int340x_thermal/
obj-$(CONFIG_INTEL_PCH_THERMAL) += intel_pch_thermal.o
obj-$(CONFIG_ST_THERMAL) += st/
+obj-$(CONFIG_QCOM_TSENS) += qcom/
obj-$(CONFIG_TEGRA_SOCTHERM) += tegra_soctherm.o
obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o
new file mode 100644
@@ -0,0 +1,11 @@
+config QCOM_TSENS
+ tristate "Qualcomm TSENS Temperature Alarm"
+ depends on THERMAL
+ depends on QCOM_QFPROM
+ depends on ARCH_QCOM || COMPILE_TEST
+ help
+ This enables the thermal sysfs driver for the TSENS device. It shows
+ up in Sysfs as a thermal zone with multiple trip points. Disabling the
+ thermal zone device via the mode file results in disabling the sensor.
+ Also able to set threshold temperature for both hot and cold and update
+ when a threshold is reached.
new file mode 100644
@@ -0,0 +1,2 @@
+obj-$(CONFIG_QCOM_TSENS) += qcom_tsens.o
+qcom_tsens-y += tsens.o tsens-common.o
new file mode 100644
@@ -0,0 +1,141 @@
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include "tsens.h"
+
+#define S0_ST_ADDR 0x1030
+#define SN_ADDR_OFFSET 0x4
+#define SN_ST_TEMP_MASK 0x3ff
+#define CAL_DEGC_PT1 30
+#define CAL_DEGC_PT2 120
+#define SLOPE_FACTOR 1000
+#define SLOPE_DEFAULT 3200
+
+char *qfprom_read(struct device *dev, const char *cname)
+{
+ struct nvmem_cell *cell;
+ ssize_t data;
+ char *ret;
+
+ cell = nvmem_cell_get(dev, cname);
+ if (IS_ERR(cell))
+ return ERR_CAST(cell);
+
+ ret = nvmem_cell_read(cell, &data);
+ nvmem_cell_put(cell);
+
+ return ret;
+}
+
+/*
+ * Use this function on devices where slope and offset calculations
+ * depend on calibration data read from qfprom. On others the slope
+ * and offset values are derived from tz->tzp->slope and tz->tzp->offset
+ * resp.
+ */
+void compute_intercept_slope(struct tsens_device *tmdev, u32 *p1,
+ u32 *p2, u32 mode)
+{
+ int i;
+ int num, den;
+
+ for (i = 0; i < tmdev->num_sensors; i++) {
+ dev_dbg(tmdev->dev,
+ "sensor%d - data_point1:%#x data_point2:%#x\n",
+ i, p1[i], p2[i]);
+
+ tmdev->sensor[i].slope = SLOPE_DEFAULT;
+ if (mode == TWO_PT_CALIB) {
+ /*
+ * slope (m) = adc_code2 - adc_code1 (y2 - y1)/
+ * temp_120_degc - temp_30_degc (x2 - x1)
+ */
+ num = p2[i] - p1[i];
+ num *= SLOPE_FACTOR;
+ den = CAL_DEGC_PT2 - CAL_DEGC_PT1;
+ tmdev->sensor[i].slope = num / den;
+ }
+
+ tmdev->sensor[i].offset = (p1[i] * SLOPE_FACTOR) -
+ (CAL_DEGC_PT1 *
+ tmdev->sensor[i].slope);
+ dev_dbg(tmdev->dev, "offset:%d\n", tmdev->sensor[i].offset);
+ }
+}
+
+static inline int code_to_degc(u32 adc_code, const struct tsens_sensor *s)
+{
+ int degc, num, den;
+
+ num = (adc_code * SLOPE_FACTOR) - s->offset;
+ den = s->slope;
+
+ if (num > 0)
+ degc = num + (den / 2);
+ else if (num < 0)
+ degc = num - (den / 2);
+ else
+ degc = num;
+
+ degc /= den;
+
+ return degc;
+}
+
+int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
+{
+ struct tsens_sensor *s = &tmdev->sensor[id];
+ u32 code;
+ unsigned int sensor_addr;
+ int last_temp = 0, ret;
+
+ sensor_addr = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
+ ret = regmap_read(tmdev->map, sensor_addr, &code);
+ if (ret)
+ return ret;
+ last_temp = code & SN_ST_TEMP_MASK;
+
+ *temp = code_to_degc(last_temp, s) * 1000;
+
+ return 0;
+}
+
+static const struct regmap_config tsens_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+int __init init_common(struct tsens_device *tmdev)
+{
+ void __iomem *base;
+
+ base = of_iomap(tmdev->dev->of_node, 0);
+ if (IS_ERR(base))
+ return -EINVAL;
+
+ tmdev->map = devm_regmap_init_mmio(tmdev->dev, base, &tsens_config);
+ if (!tmdev->map) {
+ iounmap(base);
+ return -ENODEV;
+ }
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,195 @@
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+#include "tsens.h"
+
+static int tsens_get_temp(void *data, int *temp)
+{
+ const struct tsens_sensor *s = data;
+ struct tsens_device *tmdev = s->tmdev;
+
+ return tmdev->ops->get_temp(tmdev, s->id, temp);
+}
+
+static int tsens_get_trend(void *data, long *temp)
+{
+ const struct tsens_sensor *s = data;
+ struct tsens_device *tmdev = s->tmdev;
+
+ if (tmdev->ops->get_trend)
+ return tmdev->ops->get_trend(tmdev, s->id, temp);
+
+ return -ENOTSUPP;
+}
+
+static int tsens_suspend(struct device *dev)
+{
+ struct tsens_device *tmdev = dev_get_drvdata(dev);
+
+ if (tmdev->ops && tmdev->ops->suspend)
+ return tmdev->ops->suspend(tmdev);
+
+ return 0;
+}
+
+static int tsens_resume(struct device *dev)
+{
+ struct tsens_device *tmdev = dev_get_drvdata(dev);
+
+ if (tmdev->ops && tmdev->ops->resume)
+ return tmdev->ops->resume(tmdev);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(tsens_pm_ops, tsens_suspend, tsens_resume);
+
+static const struct of_device_id tsens_table[] = {
+ {
+ .compatible = "qcom,msm8916-tsens",
+ }, {
+ .compatible = "qcom,msm8974-tsens",
+ },
+ {}
+};
+MODULE_DEVICE_TABLE(of, tsens_table);
+
+static const struct thermal_zone_of_device_ops tsens_of_ops = {
+ .get_temp = tsens_get_temp,
+ .get_trend = tsens_get_trend,
+};
+
+static int tsens_register(struct tsens_device *tmdev)
+{
+ int i;
+ struct thermal_zone_device *tzd;
+ u32 *hw_id, n = tmdev->num_sensors;
+
+ hw_id = devm_kcalloc(tmdev->dev, n, sizeof(u32), GFP_KERNEL);
+ if (!hw_id)
+ return -ENOMEM;
+
+ for (i = 0; i < tmdev->num_sensors; i++) {
+ tmdev->sensor[i].tmdev = tmdev;
+ tmdev->sensor[i].id = i;
+ tzd = devm_thermal_zone_of_sensor_register(tmdev->dev, i,
+ &tmdev->sensor[i],
+ &tsens_of_ops);
+ if (IS_ERR(tzd))
+ continue;
+ tmdev->sensor[i].tzd = tzd;
+ if (tmdev->ops->enable)
+ tmdev->ops->enable(tmdev, i);
+ }
+ return 0;
+}
+
+static int tsens_probe(struct platform_device *pdev)
+{
+ int ret, i;
+ struct device *dev;
+ struct device_node *np;
+ struct tsens_sensor *s;
+ struct tsens_device *tmdev;
+ const struct tsens_data *data;
+ const struct of_device_id *id;
+
+ if (pdev->dev.of_node)
+ dev = &pdev->dev;
+ else
+ dev = pdev->dev.parent;
+
+ np = dev->of_node;
+
+ id = of_match_node(tsens_table, np);
+ if (!id)
+ return -EINVAL;
+
+ data = id->data;
+
+ if (data->num_sensors <= 0) {
+ dev_err(dev, "invalid number of sensors\n");
+ return -EINVAL;
+ }
+
+ tmdev = devm_kzalloc(dev, sizeof(*tmdev) +
+ data->num_sensors * sizeof(*s), GFP_KERNEL);
+ if (!tmdev)
+ return -ENOMEM;
+
+ tmdev->dev = dev;
+ tmdev->num_sensors = data->num_sensors;
+ tmdev->ops = data->ops;
+ for (i = 0; i < tmdev->num_sensors; i++) {
+ if (data->hw_ids)
+ tmdev->sensor[i].hw_id = data->hw_ids[i];
+ else
+ tmdev->sensor[i].hw_id = i;
+ }
+
+ if (!tmdev->ops || !tmdev->ops->init || !tmdev->ops->get_temp)
+ return -EINVAL;
+
+ ret = tmdev->ops->init(tmdev);
+ if (ret < 0) {
+ dev_err(dev, "tsens init failed\n");
+ return ret;
+ }
+
+ if (tmdev->ops->calibrate) {
+ ret = tmdev->ops->calibrate(tmdev);
+ if (ret < 0) {
+ dev_err(dev, "tsens calibration failed\n");
+ return ret;
+ }
+ }
+
+ ret = tsens_register(tmdev);
+
+ platform_set_drvdata(pdev, tmdev);
+
+ return ret;
+}
+
+static int tsens_remove(struct platform_device *pdev)
+{
+ struct tsens_device *tmdev = platform_get_drvdata(pdev);
+
+ if (tmdev->ops->disable)
+ tmdev->ops->disable(tmdev);
+
+ return 0;
+}
+
+static struct platform_driver tsens_driver = {
+ .probe = tsens_probe,
+ .remove = tsens_remove,
+ .driver = {
+ .name = "qcom-tsens",
+ .pm = &tsens_pm_ops,
+ .of_match_table = tsens_table,
+ },
+};
+module_platform_driver(tsens_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("QCOM Temperature Sensor driver");
+MODULE_ALIAS("platform:qcom-tsens");
new file mode 100644
@@ -0,0 +1,90 @@
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#ifndef __QCOM_TSENS_H__
+#define __QCOM_TSENS_H__
+
+#define ONE_PT_CALIB 0x1
+#define ONE_PT_CALIB2 0x2
+#define TWO_PT_CALIB 0x3
+
+struct tsens_device;
+
+struct tsens_sensor {
+ struct tsens_device *tmdev;
+ struct thermal_zone_device *tzd;
+ int offset;
+ int id;
+ int hw_id;
+ int slope;
+ u32 status;
+};
+
+/**
+ * struct tsens_ops - operations as supported by the tsens device
+ * @init: Function to initialize the tsens device
+ * @calibrate: Function to calibrate the tsens device
+ * @get_temp: Function which returns the temp in millidegC
+ * @enable: Function to enable (clocks/power) tsens device
+ * @disable: Function to disable the tsens device
+ * @suspend: Function to suspend the tsens device
+ * @resume: Function to resume the tsens device
+ * @get_trend: Function to get the thermal/temp trend
+ */
+struct tsens_ops {
+ /* mandatory callbacks */
+ int (*init)(struct tsens_device *);
+ int (*calibrate)(struct tsens_device *);
+ int (*get_temp)(struct tsens_device *, int, int *);
+ /* optional callbacks */
+ int (*enable)(struct tsens_device *, int);
+ void (*disable)(struct tsens_device *);
+ int (*suspend)(struct tsens_device *);
+ int (*resume)(struct tsens_device *);
+ int (*get_trend)(struct tsens_device *, int, long *);
+};
+
+/**
+ * struct tsens_data - tsens instance specific data
+ * @num_sensors: Max number of sensors supported by platform
+ * @ops: operations the tsens instance supports
+ * @hw_ids: Subset of sensors ids supported by platform, if not the first n
+ */
+struct tsens_data {
+ const u32 num_sensors;
+ const struct tsens_ops *ops;
+ unsigned int *hw_ids;
+};
+
+/* Registers to be saved/restored across a context loss */
+struct tsens_context {
+ int threshold;
+ int control;
+};
+
+struct tsens_device {
+ struct device *dev;
+ u32 num_sensors;
+ struct regmap *map;
+ struct regmap_field *status_field;
+ struct tsens_context ctx;
+ bool trdy;
+ const struct tsens_ops *ops;
+ struct tsens_sensor sensor[0];
+};
+
+char *qfprom_read(struct device *, const char *);
+void compute_intercept_slope(struct tsens_device *, u32 *, u32 *, u32);
+int init_common(struct tsens_device *);
+int get_temp_common(struct tsens_device *, int, int *);
+
+#endif /* __QCOM_TSENS_H__ */