@@ -220,21 +220,21 @@ struct xilinx_axidma_desc_hw {
/**
* struct xilinx_cdma_desc_hw - Hardware Descriptor
* @next_desc: Next Descriptor Pointer @0x00
- * @pad1: Reserved @0x04
+ * @next_descmsb: Next Descriptor Pointer MSB @0x04
* @src_addr: Source address @0x08
- * @pad2: Reserved @0x0C
+ * @src_addrmsb: Source address MSB @0x0C
* @dest_addr: Destination address @0x10
- * @pad3: Reserved @0x14
+ * @dest_addrmsb: Destination address MSB @0x14
* @control: Control field @0x18
* @status: Status field @0x1C
*/
struct xilinx_cdma_desc_hw {
u32 next_desc;
- u32 pad1;
+ u32 next_desc_msb;
u32 src_addr;
- u32 pad2;
+ u32 src_addr_msb;
u32 dest_addr;
- u32 pad3;
+ u32 dest_addr_msb;
u32 control;
u32 status;
} __aligned(64);
@@ -1114,12 +1114,20 @@ static void xilinx_cdma_start_transfer(struct xilinx_dma_chan *chan)
}
if (chan->has_sg) {
- dma_ctrl_write(chan, XILINX_DMA_REG_CURDESC,
- head_desc->async_tx.phys);
+ if (chan->ext_addr)
+ dma_writeq(chan, XILINX_DMA_REG_CURDESC,
+ head_desc->async_tx.phys);
+ else
+ dma_ctrl_write(chan, XILINX_DMA_REG_CURDESC,
+ head_desc->async_tx.phys);
/* Update tail ptr register which will start the transfer */
- dma_ctrl_write(chan, XILINX_DMA_REG_TAILDESC,
- tail_segment->phys);
+ if (chan->ext_addr)
+ dma_writeq(chan, XILINX_DMA_REG_TAILDESC,
+ tail_segment->phys);
+ else
+ dma_ctrl_write(chan, XILINX_DMA_REG_TAILDESC,
+ tail_segment->phys);
} else {
/* In simple mode */
struct xilinx_cdma_tx_segment *segment;
@@ -1131,8 +1139,16 @@ static void xilinx_cdma_start_transfer(struct xilinx_dma_chan *chan)
hw = &segment->hw;
- dma_ctrl_write(chan, XILINX_CDMA_REG_SRCADDR, hw->src_addr);
- dma_ctrl_write(chan, XILINX_CDMA_REG_DSTADDR, hw->dest_addr);
+ if (chan->ext_addr) {
+ dma_writeq(chan, XILINX_CDMA_REG_SRCADDR, hw->src_addr);
+ dma_writeq(chan, XILINX_CDMA_REG_DSTADDR,
+ hw->dest_addr);
+ } else {
+ dma_ctrl_write(chan, XILINX_CDMA_REG_SRCADDR,
+ hw->src_addr);
+ dma_ctrl_write(chan, XILINX_CDMA_REG_DSTADDR,
+ hw->dest_addr);
+ }
/* Start the transfer */
dma_ctrl_write(chan, XILINX_DMA_REG_BTT,
@@ -1622,6 +1638,10 @@ xilinx_cdma_prep_memcpy(struct dma_chan *dchan, dma_addr_t dma_dst,
hw->control = len;
hw->src_addr = dma_src;
hw->dest_addr = dma_dst;
+ if (chan->ext_addr) {
+ hw->src_addr_msb = upper_32_bits(dma_src);
+ hw->dest_addr_msb = upper_32_bits(dma_dst);
+ }
/* Fill the previous next descriptor with current */
prev = list_last_entry(&desc->segments,
The AXI CDMA is a soft ip, which can be programmed to support 32 bit addressing or greater than 32 bit addressing. When the AXI CDMA ip is configured for 32 bit address space in simple dma mode the source/destination buffer address is specified by a single register(18h for Source buffer address and 20h for Destination buffer address). When configured in SG mode the current descriptor and tail descriptor are specified by a Single register(08h for curdesc 10h for tail desc). When the AXI CDMA core is configured for an address space greater than 32 then each buffer address or descriptor address is specified by a combination of two registers. The first register specifies the LSB 32 bits of address, while the next register specifies the MSB 32 bits of address. For example, 08h will specify the LSB 32 bits while 0Ch will specify the MSB 32 bits of the first start address. So we need to program two registers at a time. This patch adds the 64 bit addressing support to the axicdma IP in the driver. Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> --- Changes for v2: --> New patch. drivers/dma/xilinx/xilinx_vdma.c | 44 +++++++++++++++++++++++++++++----------- 1 file changed, 32 insertions(+), 12 deletions(-)