@@ -45,6 +45,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/thermal/thermal.h>
/ {
compatible = "rockchip,rk3399";
@@ -389,6 +390,95 @@
status = "disabled";
};
+ thermal-zones {
+ cpu-thermal: cpu {
+ polling-delay-passive = <100>; /* milliseconds */
+ polling-delay = <1000>; /* milliseconds */
+
+ thermal-sensors = <&tsadc 0>;
+
+ trips {
+ cpu_alert0: cpu_alert0 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+ cpu_alert1: cpu_alert1 {
+ temperature = <75000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+ cpu_crit: cpu_crit {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device =
+ <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ map1 {
+ trip = <&cpu_alert1>;
+ cooling-device =
+ <&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ gpu-thermal: gpu {
+ polling-delay-passive = <100>; /* milliseconds */
+ polling-delay = <1000>; /* milliseconds */
+
+ thermal-sensors = <&tsadc 1>;
+
+ trips {
+ gpu_alert0: gpu_alert0 {
+ temperature = <75000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+ gpu_crit: gpu_crit {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&gpu_alert0>;
+ cooling-device =
+ <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
+ tsadc: tsadc@ff260000 {
+ compatible = "rockchip,rk3399-tsadc";
+ reg = <0x0 0xff260000 0x0 0x100>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ rockchip,grf = <&grf>;
+ clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
+ clock-names = "tsadc", "apb_pclk";
+ assigned-clocks = <&cru SCLK_TSADC>;
+ assigned-clock-rates = <750000>;
+ resets = <&cru SRST_TSADC>;
+ reset-names = "tsadc-apb";
+ pinctrl-names = "init", "default", "sleep";
+ pinctrl-0 = <&otp_gpio>;
+ pinctrl-1 = <&otp_out>;
+ pinctrl-2 = <&otp_gpio>;
+ #thermal-sensor-cells = <1>;
+ rockchip,hw-tshut-temp = <95000>;
+ status = "disabled";
+ };
+
pmugrf: syscon@ff320000 {
compatible = "rockchip,rk3399-pmugrf", "syscon";
reg = <0x0 0xff320000 0x0 0x1000>;
@@ -881,6 +971,16 @@
};
};
+ tsadc {
+ otp_gpio: otp-gpio {
+ rockchip,pins = <1 6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ otp_out: otp-out {
+ rockchip,pins = <1 6 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
uart0 {
uart0_xfer: uart0-xfer {
rockchip,pins =
This adds thermal zone node to rk3399 dtsi, rk3399 thermal data is including the cpu and gpu sensor zone node. At the moment, remove the rk3368 thermal data from rk399 dtsi. The thermal zone node is the node containing all the required info for describing a thermal zone, including its cooling device bindings. The thermal zone node must contain, apart from its own properties, one sub-node containing trip nodes and one sub-node containing all the zone cooling maps. The following is the parameter is introduced: * polling-delay: The maximum number of milliseconds to wait between polls * polling-delay-passive: The maximum number of milliseconds to wait between polls when performing passive cooling. * trips: A sub-node which is a container of only trip point nodes required to describe the thermal zone. * cooling-maps: A sub-node which is a container of only cooling device map nodes, used to describe the relation between trips and cooling devices. * cooling-device: A phandle of a cooling device with its specifier, referring to which cooling device is used in this cooling specifier binding. In the cooling specifier, the first cell is the minimum cooling state and the second cell is the maximum cooling state used in this map. Signed-off-by: Caesar Wang <wxt@rock-chips.com> --- arch/arm64/boot/dts/rockchip/rk3399.dtsi | 100 +++++++++++++++++++++++++++++++ 1 file changed, 100 insertions(+)