diff mbox

[4/5] drm/bridge: Add driver for GE B850v3 LVDS/DP++ Bridge

Message ID 1464626385-19253-5-git-send-email-peter.senna@collabora.com (mailing list archive)
State New, archived
Headers show

Commit Message

Peter Senna Tschudin May 30, 2016, 4:39 p.m. UTC
This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
display bridge of the GE B850v3(imx6q-b850v3.dts). There are two physical
bridges on the video signal pipeline: a STDP4028(LVDS to DP) and a
STDP2690(DP to DP++). However the physical bridges are automatically
configured by the input video signal, and the driver has no access to
the video processing pipeline. The driver is only needed to read EDID
from the STDP2690 and to handle HPD events from the STDP4028. The driver
communicates with both bridges over i2c. The video signal pipeline is as
follows:

  Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output

Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
---
 MAINTAINERS                                |   8 +
 drivers/gpu/drm/bridge/Kconfig             |   8 +
 drivers/gpu/drm/bridge/Makefile            |   1 +
 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c | 397 +++++++++++++++++++++++++++++
 4 files changed, 414 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c

Comments

Enric Balletbo Serra May 31, 2016, 7:48 a.m. UTC | #1
Hi Peter,

Just some comments that I received when I submitted my bridge patches
and that I think can help you ...

2016-05-30 18:39 GMT+02:00 Peter Senna Tschudin <peter.senna@collabora.com>:
> This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
> display bridge of the GE B850v3(imx6q-b850v3.dts). There are two physical
> bridges on the video signal pipeline: a STDP4028(LVDS to DP) and a
> STDP2690(DP to DP++). However the physical bridges are automatically
> configured by the input video signal, and the driver has no access to
> the video processing pipeline. The driver is only needed to read EDID
> from the STDP2690 and to handle HPD events from the STDP4028. The driver
> communicates with both bridges over i2c. The video signal pipeline is as
> follows:
>
>   Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
>
> Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
> ---
>  MAINTAINERS                                |   8 +
>  drivers/gpu/drm/bridge/Kconfig             |   8 +
>  drivers/gpu/drm/bridge/Makefile            |   1 +
>  drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c | 397 +++++++++++++++++++++++++++++
>  4 files changed, 414 insertions(+)
>  create mode 100644 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3273ffa..7bb5e89 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -5009,6 +5009,14 @@ W:       https://linuxtv.org
>  S:     Maintained
>  F:     drivers/media/radio/radio-gemtek*
>
> +GENERAL ELECTRIC B850V3 LVDS/DP++ BRIDGE
> +M:     Martin Donnelly <martin.donnelly@ge.com>
> +M:     Peter Senna Tschudin <peter.senna@collabora.com>
> +M:     Martyn Welch <martyn.welch@collabora.co.uk>
> +S:     Maintained
> +F:     drivers/gpu/drm/bridge/ge_b850v3_dp2.c
> +F:     Documentation/devicetree/bindings/ge/b850v3_dp2_bridge.txt
> +
>  GENERIC GPIO I2C DRIVER
>  M:     Haavard Skinnemoen <hskinnemoen@gmail.com>
>  S:     Supported
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index 8f7423f..e9c32fc 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -52,4 +52,12 @@ config DRM_PARADE_PS8622
>
>  source "drivers/gpu/drm/bridge/analogix/Kconfig"
>
> +config DRM_GE_B850V3_LVDS_DP
> +       tristate "LVDS/DP bridge"
> +       depends on OF
> +       select DRM_KMS_HELPER
> +       select DRM_PANEL
> +       ---help---
> +         Driver for GE B850v3 DP2 LVDS to DP+ Bridge
> +

I think the maintainer prefers the entries ordered alphabetically (by
vendor, then name), so your config should go before "config
DRM_NXP_PTN3460"

>  endmenu
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index 96b13b3..ba2e355 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -6,3 +6,4 @@ obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
>  obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
>  obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
>  obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/
> +obj-$(CONFIG_DRM_GE_B850V3_LVDS_DP) += ge_b850v3_lvds_dp.o

Same here,  this needs to be sorted by vendor, then name as well. Also
I think is preferred use hyphens like the others drivers.

Hmm, I see now that CONFIG_DRM_ANALOGIX_DP is not sorted, but I guess
the preferred is be sorted.

> diff --git a/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> new file mode 100644
> index 0000000..37a4e7a
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> @@ -0,0 +1,397 @@
> +/*
> + * Driver for GE B850v3 DP display bridge
> +
> + * Copyright (c) 2016, Collabora Ltd.
> + * Copyright (c) 2016, General Electric Company
> +
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> +
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
> + * more details.
> +
> + * You should have received a copy of the GNU General Public License
> + * along with this program.  If not, see <http://www.gnu.org/licenses/>.
> +
> + * This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
> + * display bridge of the GE B850v3. There are two physical bridges on the video
> + * signal pipeline: a STDP4028(LVDS to DP) and a STDP2690(DP to DP++). However
> + * the physical bridges are automatically configured by the input video signal,
> + * and the driver has no access to the video processing pipeline. The driver is
> + * only needed to read EDID from the STDP2690 and to handle HPD events from the
> + * STDP4028. The driver communicates with both bridges over i2c. The video
> + * signal pipeline is as follows:
> + *
> + *   Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
> +
> + *
> + */
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include "drm_crtc.h"
> +#include "drm_crtc_helper.h"
> +#include "drm_edid.h"
> +#include "drmP.h"
> +
> +#define EDID_EXT_BLOCK_CNT 0x7E
> +
> +#define STDP4028_IRQ_OUT_CONF_REG 0x02
> +#define STDP4028_DPTX_IRQ_EN_REG 0x3C
> +#define STDP4028_DPTX_IRQ_STS_REG 0x3D
> +#define STDP4028_DPTX_STS_REG 0x3E
> +
> +#define STDP4028_DPTX_DP_IRQ_EN 0x1000
> +
> +#define STDP4028_DPTX_HOTPLUG_IRQ_EN 0x0400
> +#define STDP4028_DPTX_LINK_CH_IRQ_EN 0x2000
> +#define STDP4028_DPTX_IRQ_CONFIG \
> +               (STDP4028_DPTX_LINK_CH_IRQ_EN | STDP4028_DPTX_HOTPLUG_IRQ_EN)
> +
> +#define STDP4028_DPTX_HOTPLUG_STS 0x0200
> +#define STDP4028_DPTX_LINK_STS 0x1000
> +#define STDP4028_CON_STATE_CONNECTED \
> +               (STDP4028_DPTX_HOTPLUG_STS | STDP4028_DPTX_LINK_STS)
> +
> +#define STDP4028_DPTX_HOTPLUG_CH_STS 0x0400
> +#define STDP4028_DPTX_LINK_CH_STS 0x2000
> +#define STDP4028_DPTX_IRQ_CLEAR \
> +               (STDP4028_DPTX_LINK_CH_STS | STDP4028_DPTX_HOTPLUG_CH_STS)
> +
> +struct ge_b850v3_lvds_dp {
> +       struct drm_connector connector;
> +       struct drm_bridge bridge;
> +       struct i2c_client *ge_b850v3_lvds_dp_i2c;
> +       struct i2c_client *edid_i2c;
> +       struct edid *edid;
> +};
> +
> +static inline struct ge_b850v3_lvds_dp *
> +               bridge_to_ge_b850v3_lvds_dp(struct drm_bridge *bridge)
> +{
> +       return container_of(bridge, struct ge_b850v3_lvds_dp, bridge);
> +}
> +
> +static inline struct ge_b850v3_lvds_dp *
> +               connector_to_ge_b850v3_lvds_dp(struct drm_connector *connector)
> +{
> +       return container_of(connector, struct ge_b850v3_lvds_dp, connector);
> +}
> +
> +static void ge_b850v3_lvds_dp_pre_enable(struct drm_bridge *bridge)
> +{
> +}
> +

You don't need to keep empty callbacks for the (pre/post)
enable/disable drm_bridge ops anymore so you can remove this function
and the below.

> +static void ge_b850v3_lvds_dp_enable(struct drm_bridge *bridge)
> +{
> +}
> +
> +static void ge_b850v3_lvds_dp_disable(struct drm_bridge *bridge)
> +{
> +}
> +
> +static void ge_b850v3_lvds_dp_post_disable(struct drm_bridge *bridge)
> +{
> +}
> +
> +u8 *stdp2690_get_edid(struct i2c_client *client)
> +{
> +       struct i2c_adapter *adapter = client->adapter;
> +       unsigned char start = 0x00;
> +       unsigned int total_size;
> +       u8 *block = kmalloc(EDID_LENGTH, GFP_KERNEL);
> +
> +       struct i2c_msg msgs[] = {
> +               {
> +                       .addr   = client->addr,
> +                       .flags  = 0,
> +                       .len    = 1,
> +                       .buf    = &start,
> +               }, {
> +                       .addr   = client->addr,
> +                       .flags  = I2C_M_RD,
> +                       .len    = EDID_LENGTH,
> +                       .buf    = block,
> +               }
> +       };
> +
> +       if (!block)
> +               return NULL;
> +
> +       if (i2c_transfer(adapter, msgs, 2) != 2) {
> +               DRM_ERROR("Unable to read EDID.\n");
> +               goto err;
> +       }
> +
> +       if (!drm_edid_block_valid(block, 0, false, NULL)) {
> +               DRM_ERROR("Invalid EDID block\n");
> +               goto err;
> +       }
> +
> +       total_size = (block[EDID_EXT_BLOCK_CNT] + 1) * EDID_LENGTH;
> +       if (total_size > EDID_LENGTH) {
> +               kfree(block);
> +               block = kmalloc(total_size, GFP_KERNEL);
> +               if (!block)
> +                       return NULL;
> +
> +               /* Yes, read the entire buffer, and do not skip the first
> +                * EDID_LENGTH bytes.
> +                */
> +               start = 0x00;
> +               msgs[1].len = total_size;
> +               msgs[1].buf = block;
> +
> +               if (i2c_transfer(adapter, msgs, 2) != 2) {
> +                       DRM_ERROR("Unable to read EDID extension blocks.\n");
> +                       goto err;
> +               }
> +       }
> +
> +       return block;
> +
> +err:
> +       kfree(block);
> +       return NULL;
> +}
> +
> +static int ge_b850v3_lvds_dp_get_modes(struct drm_connector *connector)
> +{
> +       struct ge_b850v3_lvds_dp *ptn_bridge;
> +       struct i2c_client *client;
> +       u8 *block;
> +       int num_modes;
> +
> +       ptn_bridge = connector_to_ge_b850v3_lvds_dp(connector);

Move this assignation to ptn_bridge declaration

> +       client = ptn_bridge->edid_i2c;
> +
> +       block = stdp2690_get_edid(client);

I think you can remove the client variable and pass
ptn_bridge->edid_i2c directly to the stdp2690_get_edid function.

Note that get_modes is called several times and can be called from
userspace, you are allocating memory on every call to get_modes that I
think is not released or I'm missing something?

> +       ptn_bridge->edid = (struct edid *) block;
> +

What if block is NULL here ?

> +       drm_mode_connector_update_edid_property(connector, ptn_bridge->edid);
> +       num_modes = drm_add_edid_modes(connector, ptn_bridge->edid);
> +
> +       return num_modes;

nit: return drm_add_edid_modes(connector, ptn_bridge->edid); ? And
remove num_modes ?

> +}
> +
> +static struct drm_encoder
> +*ge_b850v3_lvds_dp_best_encoder(struct drm_connector *connector)
> +{
> +       struct ge_b850v3_lvds_dp *ptn_bridge =
> +               connector_to_ge_b850v3_lvds_dp(connector);
> +
> +       return ptn_bridge->bridge.encoder;
> +}
> +
> +static const struct
> +drm_connector_helper_funcs ge_b850v3_lvds_dp_connector_helper_funcs = {
> +       .get_modes = ge_b850v3_lvds_dp_get_modes,
> +       .best_encoder = ge_b850v3_lvds_dp_best_encoder,
> +};
> +
> +static enum drm_connector_status ge_b850v3_lvds_dp_detect(
> +               struct drm_connector *connector, bool force)
> +{
> +       struct ge_b850v3_lvds_dp *ptn_bridge =
> +                       connector_to_ge_b850v3_lvds_dp(connector);
> +       struct i2c_client *ge_b850v3_lvds_dp_i2c =
> +                       ptn_bridge->ge_b850v3_lvds_dp_i2c;
> +       s32 link_state;
> +
> +       link_state = i2c_smbus_read_word_data(ge_b850v3_lvds_dp_i2c,
> +                       STDP4028_DPTX_STS_REG);
> +
> +       if (link_state == STDP4028_CON_STATE_CONNECTED)
> +               return connector_status_connected;
> +
> +       if (link_state == 0)
> +               return connector_status_disconnected;
> +
> +       return connector_status_unknown;
> +}
> +
> +static void ge_b850v3_lvds_dp_connector_force(struct drm_connector *connector)
> +{
> +}
> +

Guess you can remove this empty callback.

> +static void ge_b850v3_lvds_dp_connector_destroy(struct drm_connector *connector)
> +{
> +       drm_connector_cleanup(connector);
> +}
> +
> +static const struct drm_connector_funcs ge_b850v3_lvds_dp_connector_funcs = {
> +       .dpms = drm_helper_connector_dpms,
> +       .fill_modes = drm_helper_probe_single_connector_modes,
> +       .detect = ge_b850v3_lvds_dp_detect,
> +       .destroy = ge_b850v3_lvds_dp_connector_destroy,
> +       .force = ge_b850v3_lvds_dp_connector_force,

Remove .force

> +};
> +
> +static irqreturn_t ge_b850v3_lvds_dp_irq_handler(int irq, void *dev_id)
> +{
> +       struct ge_b850v3_lvds_dp *ptn_bridge = dev_id;
> +       struct i2c_client *ge_b850v3_lvds_dp_i2c
> +                       = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> +
> +       i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> +                       STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> +       if (ptn_bridge->connector.dev)
> +               drm_kms_helper_hotplug_event(ptn_bridge->connector.dev);
> +
> +       return IRQ_HANDLED;
> +

Remove the empty line.

> +}
> +
> +static int ge_b850v3_lvds_dp_attach(struct drm_bridge *bridge)
> +{
> +       struct ge_b850v3_lvds_dp *ptn_bridge
> +                       = bridge_to_ge_b850v3_lvds_dp(bridge);
> +       struct drm_connector *connector = &ptn_bridge->connector;
> +       struct i2c_client *ge_b850v3_lvds_dp_i2c
> +                       = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> +       int ret;
> +
> +       if (!bridge->encoder) {
> +               DRM_ERROR("Parent encoder object not found");
> +               return -ENODEV;
> +       }
> +
> +       connector->polled = DRM_CONNECTOR_POLL_HPD;
> +
> +       drm_connector_helper_add(connector,
> +                       &ge_b850v3_lvds_dp_connector_helper_funcs);
> +
> +       ret = drm_connector_init(bridge->dev, connector,
> +                       &ge_b850v3_lvds_dp_connector_funcs,
> +                       DRM_MODE_CONNECTOR_DisplayPort);
> +       if (ret) {
> +               DRM_ERROR("Failed to initialize connector with drm\n");
> +               return ret;
> +       }
> +
> +       ret = drm_mode_connector_attach_encoder(connector, bridge->encoder);
> +       if (ret)
> +               return ret;
> +
> +       drm_bridge_enable(bridge);
> +       if (ge_b850v3_lvds_dp_i2c->irq) {
> +               drm_helper_hpd_irq_event(connector->dev);
> +
> +               ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
> +                               ge_b850v3_lvds_dp_i2c->irq, NULL,
> +                               ge_b850v3_lvds_dp_irq_handler,
> +                               IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
> +                               "ge_b850v3_lvds_dp", ptn_bridge);
> +               if (ret)
> +                       return ret;
> +       }
> +
> +       return 0;
> +}
> +
> +static const struct drm_bridge_funcs ge_b850v3_lvds_dp_funcs = {
> +       .pre_enable = ge_b850v3_lvds_dp_pre_enable,
> +       .enable = ge_b850v3_lvds_dp_enable,
> +       .disable = ge_b850v3_lvds_dp_disable,
> +       .post_disable = ge_b850v3_lvds_dp_post_disable,

Remove the above empty callbacks.

> +       .attach = ge_b850v3_lvds_dp_attach,
> +};
> +
> +static int ge_b850v3_lvds_dp_probe(struct i2c_client *ge_b850v3_lvds_dp_i2c,
> +                               const struct i2c_device_id *id)
> +{
> +       struct device *dev = &ge_b850v3_lvds_dp_i2c->dev;
> +       struct ge_b850v3_lvds_dp *ptn_bridge;
> +

Remove this empty line between these two blocks.

> +       int ret;
> +       u32 edid_i2c_reg;
> +
> +       ptn_bridge = devm_kzalloc(dev, sizeof(*ptn_bridge), GFP_KERNEL);
> +       if (!ptn_bridge)
> +               return -ENOMEM;
> +
> +       ptn_bridge->ge_b850v3_lvds_dp_i2c = ge_b850v3_lvds_dp_i2c;
> +       ptn_bridge->bridge.driver_private = ptn_bridge;
> +       i2c_set_clientdata(ge_b850v3_lvds_dp_i2c, ptn_bridge);
> +
> +       ret = of_property_read_u32(dev->of_node, "edid-reg", &edid_i2c_reg);
> +       if (ret) {
> +               dev_err(dev, "edid-reg not specified, aborting...\n");

Use DRM_ERROR?

> +               return -ENODEV;
> +       }
> +
> +       ptn_bridge->edid_i2c = devm_kzalloc(dev,
> +                       sizeof(struct i2c_client), GFP_KERNEL);
> +
> +       if (!ptn_bridge->edid_i2c)
> +               return -ENOMEM;
> +
> +       memcpy(ptn_bridge->edid_i2c, ge_b850v3_lvds_dp_i2c,
> +                       sizeof(struct i2c_client));
> +
> +       ptn_bridge->edid_i2c->addr = (unsigned short) edid_i2c_reg;
> +

Remove empty line.

> +
> +       /* Configures the bridge to re-enable interrupts after each ack */
> +       i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> +                       STDP4028_IRQ_OUT_CONF_REG, STDP4028_DPTX_DP_IRQ_EN);
> +       i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> +                       STDP4028_DPTX_IRQ_EN_REG, STDP4028_DPTX_IRQ_CONFIG);
> +
> +       /* Clear pending interrupts since power up. */
> +       i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> +                       STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> +       ptn_bridge->bridge.funcs = &ge_b850v3_lvds_dp_funcs;
> +       ptn_bridge->bridge.of_node = dev->of_node;
> +       ret = drm_bridge_add(&ptn_bridge->bridge);
> +       if (ret) {
> +               DRM_ERROR("Failed to add bridge\n");
> +               return ret;
> +       }
> +
> +       return 0;
> +}
> +
> +static int ge_b850v3_lvds_dp_remove(struct i2c_client *ge_b850v3_lvds_dp_i2c)
> +{
> +       struct ge_b850v3_lvds_dp *ptn_bridge =
> +               i2c_get_clientdata(ge_b850v3_lvds_dp_i2c);
> +
> +       drm_bridge_remove(&ptn_bridge->bridge);
> +
> +       return 0;
> +}
> +
> +static const struct i2c_device_id ge_b850v3_lvds_dp_i2c_table[] = {
> +       {"b850v3_lvds_dp", 0},
> +       {},
> +};
> +MODULE_DEVICE_TABLE(i2c, ge_b850v3_lvds_dp_i2c_table);
> +
> +static const struct of_device_id ge_b850v3_lvds_dp_match[] = {
> +       { .compatible = "ge,b850v3_lvds_dp" },
> +       {},
> +};
> +MODULE_DEVICE_TABLE(of, ge_b850v3_lvds_dp_match);
> +
> +static struct i2c_driver ge_b850v3_lvds_dp_driver = {
> +       .id_table       = ge_b850v3_lvds_dp_i2c_table,
> +       .probe          = ge_b850v3_lvds_dp_probe,
> +       .remove         = ge_b850v3_lvds_dp_remove,
> +       .driver         = {
> +               .name           = "ge,b850v3_lvds_dp",
> +               .of_match_table = ge_b850v3_lvds_dp_match,
> +       },
> +};
> +module_i2c_driver(ge_b850v3_lvds_dp_driver);
> +
> +MODULE_AUTHOR("Peter Senna Tschudin <peter.senna@collabora.com>");
> +MODULE_AUTHOR("Martyn Welch <martyn.welch@collabora.co.uk>");
> +MODULE_DESCRIPTION("GE LVDS to DP++ bridge)");
> +MODULE_LICENSE("GPL v2");
> --
> 2.5.5
>

Best regards,
   Enric
diff mbox

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 3273ffa..7bb5e89 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5009,6 +5009,14 @@  W:	https://linuxtv.org
 S:	Maintained
 F:	drivers/media/radio/radio-gemtek*
 
+GENERAL ELECTRIC B850V3 LVDS/DP++ BRIDGE
+M:	Martin Donnelly <martin.donnelly@ge.com>
+M:	Peter Senna Tschudin <peter.senna@collabora.com>
+M:	Martyn Welch <martyn.welch@collabora.co.uk>
+S:	Maintained
+F:	drivers/gpu/drm/bridge/ge_b850v3_dp2.c
+F:	Documentation/devicetree/bindings/ge/b850v3_dp2_bridge.txt
+
 GENERIC GPIO I2C DRIVER
 M:	Haavard Skinnemoen <hskinnemoen@gmail.com>
 S:	Supported
diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index 8f7423f..e9c32fc 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -52,4 +52,12 @@  config DRM_PARADE_PS8622
 
 source "drivers/gpu/drm/bridge/analogix/Kconfig"
 
+config DRM_GE_B850V3_LVDS_DP
+	tristate "LVDS/DP bridge"
+	depends on OF
+	select DRM_KMS_HELPER
+	select DRM_PANEL
+	---help---
+	  Driver for GE B850v3 DP2 LVDS to DP+ Bridge
+
 endmenu
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 96b13b3..ba2e355 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -6,3 +6,4 @@  obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
 obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
 obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
 obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/
+obj-$(CONFIG_DRM_GE_B850V3_LVDS_DP) += ge_b850v3_lvds_dp.o
diff --git a/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
new file mode 100644
index 0000000..37a4e7a
--- /dev/null
+++ b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
@@ -0,0 +1,397 @@ 
+/*
+ * Driver for GE B850v3 DP display bridge
+
+ * Copyright (c) 2016, Collabora Ltd.
+ * Copyright (c) 2016, General Electric Company
+
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+ * This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
+ * display bridge of the GE B850v3. There are two physical bridges on the video
+ * signal pipeline: a STDP4028(LVDS to DP) and a STDP2690(DP to DP++). However
+ * the physical bridges are automatically configured by the input video signal,
+ * and the driver has no access to the video processing pipeline. The driver is
+ * only needed to read EDID from the STDP2690 and to handle HPD events from the
+ * STDP4028. The driver communicates with both bridges over i2c. The video
+ * signal pipeline is as follows:
+ *
+ *   Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
+
+ *
+ */
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include "drm_crtc.h"
+#include "drm_crtc_helper.h"
+#include "drm_edid.h"
+#include "drmP.h"
+
+#define EDID_EXT_BLOCK_CNT 0x7E
+
+#define STDP4028_IRQ_OUT_CONF_REG 0x02
+#define STDP4028_DPTX_IRQ_EN_REG 0x3C
+#define STDP4028_DPTX_IRQ_STS_REG 0x3D
+#define STDP4028_DPTX_STS_REG 0x3E
+
+#define STDP4028_DPTX_DP_IRQ_EN 0x1000
+
+#define STDP4028_DPTX_HOTPLUG_IRQ_EN 0x0400
+#define STDP4028_DPTX_LINK_CH_IRQ_EN 0x2000
+#define STDP4028_DPTX_IRQ_CONFIG \
+		(STDP4028_DPTX_LINK_CH_IRQ_EN | STDP4028_DPTX_HOTPLUG_IRQ_EN)
+
+#define STDP4028_DPTX_HOTPLUG_STS 0x0200
+#define STDP4028_DPTX_LINK_STS 0x1000
+#define STDP4028_CON_STATE_CONNECTED \
+		(STDP4028_DPTX_HOTPLUG_STS | STDP4028_DPTX_LINK_STS)
+
+#define STDP4028_DPTX_HOTPLUG_CH_STS 0x0400
+#define STDP4028_DPTX_LINK_CH_STS 0x2000
+#define STDP4028_DPTX_IRQ_CLEAR \
+		(STDP4028_DPTX_LINK_CH_STS | STDP4028_DPTX_HOTPLUG_CH_STS)
+
+struct ge_b850v3_lvds_dp {
+	struct drm_connector connector;
+	struct drm_bridge bridge;
+	struct i2c_client *ge_b850v3_lvds_dp_i2c;
+	struct i2c_client *edid_i2c;
+	struct edid *edid;
+};
+
+static inline struct ge_b850v3_lvds_dp *
+		bridge_to_ge_b850v3_lvds_dp(struct drm_bridge *bridge)
+{
+	return container_of(bridge, struct ge_b850v3_lvds_dp, bridge);
+}
+
+static inline struct ge_b850v3_lvds_dp *
+		connector_to_ge_b850v3_lvds_dp(struct drm_connector *connector)
+{
+	return container_of(connector, struct ge_b850v3_lvds_dp, connector);
+}
+
+static void ge_b850v3_lvds_dp_pre_enable(struct drm_bridge *bridge)
+{
+}
+
+static void ge_b850v3_lvds_dp_enable(struct drm_bridge *bridge)
+{
+}
+
+static void ge_b850v3_lvds_dp_disable(struct drm_bridge *bridge)
+{
+}
+
+static void ge_b850v3_lvds_dp_post_disable(struct drm_bridge *bridge)
+{
+}
+
+u8 *stdp2690_get_edid(struct i2c_client *client)
+{
+	struct i2c_adapter *adapter = client->adapter;
+	unsigned char start = 0x00;
+	unsigned int total_size;
+	u8 *block = kmalloc(EDID_LENGTH, GFP_KERNEL);
+
+	struct i2c_msg msgs[] = {
+		{
+			.addr	= client->addr,
+			.flags	= 0,
+			.len	= 1,
+			.buf	= &start,
+		}, {
+			.addr	= client->addr,
+			.flags	= I2C_M_RD,
+			.len	= EDID_LENGTH,
+			.buf	= block,
+		}
+	};
+
+	if (!block)
+		return NULL;
+
+	if (i2c_transfer(adapter, msgs, 2) != 2) {
+		DRM_ERROR("Unable to read EDID.\n");
+		goto err;
+	}
+
+	if (!drm_edid_block_valid(block, 0, false, NULL)) {
+		DRM_ERROR("Invalid EDID block\n");
+		goto err;
+	}
+
+	total_size = (block[EDID_EXT_BLOCK_CNT] + 1) * EDID_LENGTH;
+	if (total_size > EDID_LENGTH) {
+		kfree(block);
+		block = kmalloc(total_size, GFP_KERNEL);
+		if (!block)
+			return NULL;
+
+		/* Yes, read the entire buffer, and do not skip the first
+		 * EDID_LENGTH bytes.
+		 */
+		start = 0x00;
+		msgs[1].len = total_size;
+		msgs[1].buf = block;
+
+		if (i2c_transfer(adapter, msgs, 2) != 2) {
+			DRM_ERROR("Unable to read EDID extension blocks.\n");
+			goto err;
+		}
+	}
+
+	return block;
+
+err:
+	kfree(block);
+	return NULL;
+}
+
+static int ge_b850v3_lvds_dp_get_modes(struct drm_connector *connector)
+{
+	struct ge_b850v3_lvds_dp *ptn_bridge;
+	struct i2c_client *client;
+	u8 *block;
+	int num_modes;
+
+	ptn_bridge = connector_to_ge_b850v3_lvds_dp(connector);
+	client = ptn_bridge->edid_i2c;
+
+	block = stdp2690_get_edid(client);
+	ptn_bridge->edid = (struct edid *) block;
+
+	drm_mode_connector_update_edid_property(connector, ptn_bridge->edid);
+	num_modes = drm_add_edid_modes(connector, ptn_bridge->edid);
+
+	return num_modes;
+}
+
+static struct drm_encoder
+*ge_b850v3_lvds_dp_best_encoder(struct drm_connector *connector)
+{
+	struct ge_b850v3_lvds_dp *ptn_bridge =
+		connector_to_ge_b850v3_lvds_dp(connector);
+
+	return ptn_bridge->bridge.encoder;
+}
+
+static const struct
+drm_connector_helper_funcs ge_b850v3_lvds_dp_connector_helper_funcs = {
+	.get_modes = ge_b850v3_lvds_dp_get_modes,
+	.best_encoder = ge_b850v3_lvds_dp_best_encoder,
+};
+
+static enum drm_connector_status ge_b850v3_lvds_dp_detect(
+		struct drm_connector *connector, bool force)
+{
+	struct ge_b850v3_lvds_dp *ptn_bridge =
+			connector_to_ge_b850v3_lvds_dp(connector);
+	struct i2c_client *ge_b850v3_lvds_dp_i2c =
+			ptn_bridge->ge_b850v3_lvds_dp_i2c;
+	s32 link_state;
+
+	link_state = i2c_smbus_read_word_data(ge_b850v3_lvds_dp_i2c,
+			STDP4028_DPTX_STS_REG);
+
+	if (link_state == STDP4028_CON_STATE_CONNECTED)
+		return connector_status_connected;
+
+	if (link_state == 0)
+		return connector_status_disconnected;
+
+	return connector_status_unknown;
+}
+
+static void ge_b850v3_lvds_dp_connector_force(struct drm_connector *connector)
+{
+}
+
+static void ge_b850v3_lvds_dp_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_cleanup(connector);
+}
+
+static const struct drm_connector_funcs ge_b850v3_lvds_dp_connector_funcs = {
+	.dpms = drm_helper_connector_dpms,
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.detect = ge_b850v3_lvds_dp_detect,
+	.destroy = ge_b850v3_lvds_dp_connector_destroy,
+	.force = ge_b850v3_lvds_dp_connector_force,
+};
+
+static irqreturn_t ge_b850v3_lvds_dp_irq_handler(int irq, void *dev_id)
+{
+	struct ge_b850v3_lvds_dp *ptn_bridge = dev_id;
+	struct i2c_client *ge_b850v3_lvds_dp_i2c
+			= ptn_bridge->ge_b850v3_lvds_dp_i2c;
+
+	i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+			STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
+
+	if (ptn_bridge->connector.dev)
+		drm_kms_helper_hotplug_event(ptn_bridge->connector.dev);
+
+	return IRQ_HANDLED;
+
+}
+
+static int ge_b850v3_lvds_dp_attach(struct drm_bridge *bridge)
+{
+	struct ge_b850v3_lvds_dp *ptn_bridge
+			= bridge_to_ge_b850v3_lvds_dp(bridge);
+	struct drm_connector *connector = &ptn_bridge->connector;
+	struct i2c_client *ge_b850v3_lvds_dp_i2c
+			= ptn_bridge->ge_b850v3_lvds_dp_i2c;
+	int ret;
+
+	if (!bridge->encoder) {
+		DRM_ERROR("Parent encoder object not found");
+		return -ENODEV;
+	}
+
+	connector->polled = DRM_CONNECTOR_POLL_HPD;
+
+	drm_connector_helper_add(connector,
+			&ge_b850v3_lvds_dp_connector_helper_funcs);
+
+	ret = drm_connector_init(bridge->dev, connector,
+			&ge_b850v3_lvds_dp_connector_funcs,
+			DRM_MODE_CONNECTOR_DisplayPort);
+	if (ret) {
+		DRM_ERROR("Failed to initialize connector with drm\n");
+		return ret;
+	}
+
+	ret = drm_mode_connector_attach_encoder(connector, bridge->encoder);
+	if (ret)
+		return ret;
+
+	drm_bridge_enable(bridge);
+	if (ge_b850v3_lvds_dp_i2c->irq) {
+		drm_helper_hpd_irq_event(connector->dev);
+
+		ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
+				ge_b850v3_lvds_dp_i2c->irq, NULL,
+				ge_b850v3_lvds_dp_irq_handler,
+				IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+				"ge_b850v3_lvds_dp", ptn_bridge);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static const struct drm_bridge_funcs ge_b850v3_lvds_dp_funcs = {
+	.pre_enable = ge_b850v3_lvds_dp_pre_enable,
+	.enable = ge_b850v3_lvds_dp_enable,
+	.disable = ge_b850v3_lvds_dp_disable,
+	.post_disable = ge_b850v3_lvds_dp_post_disable,
+	.attach = ge_b850v3_lvds_dp_attach,
+};
+
+static int ge_b850v3_lvds_dp_probe(struct i2c_client *ge_b850v3_lvds_dp_i2c,
+				const struct i2c_device_id *id)
+{
+	struct device *dev = &ge_b850v3_lvds_dp_i2c->dev;
+	struct ge_b850v3_lvds_dp *ptn_bridge;
+
+	int ret;
+	u32 edid_i2c_reg;
+
+	ptn_bridge = devm_kzalloc(dev, sizeof(*ptn_bridge), GFP_KERNEL);
+	if (!ptn_bridge)
+		return -ENOMEM;
+
+	ptn_bridge->ge_b850v3_lvds_dp_i2c = ge_b850v3_lvds_dp_i2c;
+	ptn_bridge->bridge.driver_private = ptn_bridge;
+	i2c_set_clientdata(ge_b850v3_lvds_dp_i2c, ptn_bridge);
+
+	ret = of_property_read_u32(dev->of_node, "edid-reg", &edid_i2c_reg);
+	if (ret) {
+		dev_err(dev, "edid-reg not specified, aborting...\n");
+		return -ENODEV;
+	}
+
+	ptn_bridge->edid_i2c = devm_kzalloc(dev,
+			sizeof(struct i2c_client), GFP_KERNEL);
+
+	if (!ptn_bridge->edid_i2c)
+		return -ENOMEM;
+
+	memcpy(ptn_bridge->edid_i2c, ge_b850v3_lvds_dp_i2c,
+			sizeof(struct i2c_client));
+
+	ptn_bridge->edid_i2c->addr = (unsigned short) edid_i2c_reg;
+
+
+	/* Configures the bridge to re-enable interrupts after each ack */
+	i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+			STDP4028_IRQ_OUT_CONF_REG, STDP4028_DPTX_DP_IRQ_EN);
+	i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+			STDP4028_DPTX_IRQ_EN_REG, STDP4028_DPTX_IRQ_CONFIG);
+
+	/* Clear pending interrupts since power up. */
+	i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+			STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
+
+	ptn_bridge->bridge.funcs = &ge_b850v3_lvds_dp_funcs;
+	ptn_bridge->bridge.of_node = dev->of_node;
+	ret = drm_bridge_add(&ptn_bridge->bridge);
+	if (ret) {
+		DRM_ERROR("Failed to add bridge\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ge_b850v3_lvds_dp_remove(struct i2c_client *ge_b850v3_lvds_dp_i2c)
+{
+	struct ge_b850v3_lvds_dp *ptn_bridge =
+		i2c_get_clientdata(ge_b850v3_lvds_dp_i2c);
+
+	drm_bridge_remove(&ptn_bridge->bridge);
+
+	return 0;
+}
+
+static const struct i2c_device_id ge_b850v3_lvds_dp_i2c_table[] = {
+	{"b850v3_lvds_dp", 0},
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, ge_b850v3_lvds_dp_i2c_table);
+
+static const struct of_device_id ge_b850v3_lvds_dp_match[] = {
+	{ .compatible = "ge,b850v3_lvds_dp" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ge_b850v3_lvds_dp_match);
+
+static struct i2c_driver ge_b850v3_lvds_dp_driver = {
+	.id_table	= ge_b850v3_lvds_dp_i2c_table,
+	.probe		= ge_b850v3_lvds_dp_probe,
+	.remove		= ge_b850v3_lvds_dp_remove,
+	.driver		= {
+		.name		= "ge,b850v3_lvds_dp",
+		.of_match_table = ge_b850v3_lvds_dp_match,
+	},
+};
+module_i2c_driver(ge_b850v3_lvds_dp_driver);
+
+MODULE_AUTHOR("Peter Senna Tschudin <peter.senna@collabora.com>");
+MODULE_AUTHOR("Martyn Welch <martyn.welch@collabora.co.uk>");
+MODULE_DESCRIPTION("GE LVDS to DP++ bridge)");
+MODULE_LICENSE("GPL v2");