| Message ID | 1464937059-19349-1-git-send-email-hongtao.jia@nxp.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Fri, Jun 03, 2016 at 02:57:33PM +0800, Jia Hongtao wrote: > For different types of SoC the sensor id and endianness may vary. > "#thermal-sensor-cells" is used to provide sensor id information. > "little-endian" property is to tell the endianness of TMU. > > Signed-off-by: Jia Hongtao <hongtao.jia@nxp.com> > --- > .../devicetree/bindings/thermal/qoriq-thermal.txt | 19 +++++++++++++------ > 1 file changed, 13 insertions(+), 6 deletions(-) > > diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt > index 66223d5..8eeef80 100644 > --- a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt > +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt > @@ -1,22 +1,28 @@ > * Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs > > Required properties: > -- compatible : Must include "fsl,qoriq-tmu". The version of the device is > +- compatible: Must include "fsl,qoriq-tmu". The version of the device is Please split functional changes from formatting changes. This one seems pretty pointless. > determined by the TMU IP Block Revision Register (IPBRR0) at > offset 0x0BF8. > - Table of correspondences between IPBRR0 values and example chips: > + Table of correspondences between IPBRR0 values and example chips: > Value Device > ---------- ----- > 0x01900102 T1040 > -- reg : Address range of TMU registers. > -- interrupts : Contains the interrupt for TMU. > -- fsl,tmu-range : The values to be programmed into TTRnCR, as specified by > +- reg: Address range of TMU registers. > +- interrupts: Contains the interrupt for TMU. > +- fsl,tmu-range: The values to be programmed into TTRnCR, as specified by > the SoC reference manual. The first cell is TTR0CR, the second is > TTR1CR, etc. > -- fsl,tmu-calibration : A list of cell pairs containing temperature > +- fsl,tmu-calibration: A list of cell pairs containing temperature > calibration data, as specified by the SoC reference manual. > The first cell of each pair is the value to be written to TTCFGR, > and the second is the value to be written to TSCFGR. > +- #thermal-sensor-cells: Must be 1. The sensor specifier is the monitoring > + site ID, and represents the "n" in TRITSRn and TRATSRn. > + > +Optional property: > +- little-endian: If present, the TMU registers are little endian. If absent, > + the default is big endian. > > Example: > > @@ -60,4 +66,5 @@ tmu@f0000 { > > 0x00030000 0x00000012 > 0x00030001 0x0000001d>; > + #thermal-sensor-cells = <1>; > }; > -- > 2.1.0.27.g96db324 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> -----邮件原件----- > 发件人: Rob Herring [mailto:robh@kernel.org] > 发送时间: Monday, June 06, 2016 9:47 PM > 收件人: Hongtao Jia <hongtao.jia@nxp.com> > 抄送: edubezval@gmail.com; rui.zhang@intel.com; galak@codeaurora.org; > Scott Wood <scott.wood@nxp.com>; shawnguo@kernel.org; > devicetree@vger.kernel.org; linux-pm@vger.kernel.org; linux- > kernel@vger.kernel.org; linuxppc-dev@lists.ozlabs.org; linux-arm- > kernel@lists.infradead.org > 主题: Re: [PATCH 1/7] dt-bindings: Update QorIQ TMU thermal bindings > > On Fri, Jun 03, 2016 at 02:57:33PM +0800, Jia Hongtao wrote: > > For different types of SoC the sensor id and endianness may vary. > > "#thermal-sensor-cells" is used to provide sensor id information. > > "little-endian" property is to tell the endianness of TMU. > > > > Signed-off-by: Jia Hongtao <hongtao.jia@nxp.com> > > --- > > .../devicetree/bindings/thermal/qoriq-thermal.txt | 19 +++++++++++++--- > --- > > 1 file changed, 13 insertions(+), 6 deletions(-) > > > > diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt > b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt > > index 66223d5..8eeef80 100644 > > --- a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt > > +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt > > @@ -1,22 +1,28 @@ > > * Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs > > > > Required properties: > > -- compatible : Must include "fsl,qoriq-tmu". The version of the device is > > +- compatible: Must include "fsl,qoriq-tmu". The version of the device is > > Please split functional changes from formatting changes. This one seems > pretty pointless. I will remove formatting changes in the next version. Thanks. > > > determined by the TMU IP Block Revision Register (IPBRR0) at > > offset 0x0BF8. > > - Table of correspondences between IPBRR0 values and example chips: > > + Table of correspondences between IPBRR0 values and example chips: > > Value Device > > ---------- ----- > > 0x01900102 T1040 > > -- reg : Address range of TMU registers. > > -- interrupts : Contains the interrupt for TMU. > > -- fsl,tmu-range : The values to be programmed into TTRnCR, as specified by > > +- reg: Address range of TMU registers. > > +- interrupts: Contains the interrupt for TMU. > > +- fsl,tmu-range: The values to be programmed into TTRnCR, as specified by > > the SoC reference manual. The first cell is TTR0CR, the second is > > TTR1CR, etc. > > -- fsl,tmu-calibration : A list of cell pairs containing temperature > > +- fsl,tmu-calibration: A list of cell pairs containing temperature > > calibration data, as specified by the SoC reference manual. > > The first cell of each pair is the value to be written to TTCFGR, > > and the second is the value to be written to TSCFGR. > > +- #thermal-sensor-cells: Must be 1. The sensor specifier is the monitoring > > + site ID, and represents the "n" in TRITSRn and TRATSRn. > > + > > +Optional property: > > +- little-endian: If present, the TMU registers are little endian. If absent, > > + the default is big endian. > > > > Example: > > > > @@ -60,4 +66,5 @@ tmu@f0000 { > > > > 0x00030000 0x00000012 > > 0x00030001 0x0000001d>; > > + #thermal-sensor-cells = <1>; > > }; > > -- > > 2.1.0.27.g96db324 > > > > > > _______________________________________________ > > linux-arm-kernel mailing list > > linux-arm-kernel@lists.infradead.org > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt index 66223d5..8eeef80 100644 --- a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt @@ -1,22 +1,28 @@ * Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs Required properties: -- compatible : Must include "fsl,qoriq-tmu". The version of the device is +- compatible: Must include "fsl,qoriq-tmu". The version of the device is determined by the TMU IP Block Revision Register (IPBRR0) at offset 0x0BF8. - Table of correspondences between IPBRR0 values and example chips: + Table of correspondences between IPBRR0 values and example chips: Value Device ---------- ----- 0x01900102 T1040 -- reg : Address range of TMU registers. -- interrupts : Contains the interrupt for TMU. -- fsl,tmu-range : The values to be programmed into TTRnCR, as specified by +- reg: Address range of TMU registers. +- interrupts: Contains the interrupt for TMU. +- fsl,tmu-range: The values to be programmed into TTRnCR, as specified by the SoC reference manual. The first cell is TTR0CR, the second is TTR1CR, etc. -- fsl,tmu-calibration : A list of cell pairs containing temperature +- fsl,tmu-calibration: A list of cell pairs containing temperature calibration data, as specified by the SoC reference manual. The first cell of each pair is the value to be written to TTCFGR, and the second is the value to be written to TSCFGR. +- #thermal-sensor-cells: Must be 1. The sensor specifier is the monitoring + site ID, and represents the "n" in TRITSRn and TRATSRn. + +Optional property: +- little-endian: If present, the TMU registers are little endian. If absent, + the default is big endian. Example: @@ -60,4 +66,5 @@ tmu@f0000 { 0x00030000 0x00000012 0x00030001 0x0000001d>; + #thermal-sensor-cells = <1>; };
For different types of SoC the sensor id and endianness may vary. "#thermal-sensor-cells" is used to provide sensor id information. "little-endian" property is to tell the endianness of TMU. Signed-off-by: Jia Hongtao <hongtao.jia@nxp.com> --- .../devicetree/bindings/thermal/qoriq-thermal.txt | 19 +++++++++++++------ 1 file changed, 13 insertions(+), 6 deletions(-)