diff mbox

[5/5] ARM: dts: add Qualcomm APQ8060-based Dragonboard

Message ID 1465918259-11138-6-git-send-email-linus.walleij@linaro.org (mailing list archive)
State New, archived
Headers show

Commit Message

Linus Walleij June 14, 2016, 3:30 p.m. UTC 
This is the first Dragonboard based on APQ8060 and PM8058. It
was produced in 2011 in cooperation between Qualcomm and
BSQUARE.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/Makefile                     |   1 +
 arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 557 +++++++++++++++++++++++++
 2 files changed, 558 insertions(+)
 create mode 100644 arch/arm/boot/dts/qcom-apq8060-dragonboard.dts

Comments

Stephen Boyd June 14, 2016, 7:11 p.m. UTC | #1 
On 06/14, Linus Walleij wrote:
> +/ {
> +	model = "Qualcomm APQ8060 Dragonboard";
> +	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
> +
> +	aliases {
> +		serial0 = &gsbi12_serial;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
> +		/* Main power of the board: 3.7V */
> +		vph: regulator-fixed@1 {
> +			compatible = "regulator-fixed";
> +			regulator-min-microvolt = <3700000>;
> +			regulator-max-microvolt = <3700000>;
> +			regulator-name = "VPH";
> +			regulator-type = "voltage";
> +			regulator-always-on;
> +			regulator-boot-on;
> +		};
> +	};
> +
> +	/* This is a levelshifter for SDCC5 */
> +	dragon_vio_txb: txb0104rgyr {
> +		compatible = "regulator-fixed";
> +		regulator-name = "Dragon SDCC levelshifter";
> +		vin-supply = <&pm8058_l14>;
> +		regulator-always-on;
> +	};

Why not put this under regulators node as well?

> +
> +	soc {
> +		gsbi@19c00000 {
> +			status = "ok";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&dragon_serial0_pins>;
> +			qcom,mode = <GSBI_PROT_I2C_UART>;
> +			serial@19c40000 {
> +				status = "ok";
> +			};
> +		};
> +	};
> +};
> +
> +/* Intenal 3.69 GiB eMMC */
> +&sdcc1 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&dragon_sdcc1_pins>;
> +	vmmc-supply = <&pm8901_l5>;
> +	vqmmc-supply = <&pm8901_lvs0>;
> +};

I think we're following a non-phandle approach to filling out
board dts files. We didn't follow it that well on 8660 surf,
probably because it was so basic, but it would be nice to follow
that style here as well and populate board properties in nodes
like how gsbi@19c00000 has been done. I'll leave this up to Andy
though as he's the maintainer here.
Linus Walleij June 15, 2016, 1:37 p.m. UTC | #2 
On Tue, Jun 14, 2016 at 9:11 PM, Stephen Boyd <sboyd@codeaurora.org> wrote:

>> +/* Intenal 3.69 GiB eMMC */
>> +&sdcc1 {
>> +     status = "okay";
>> +     pinctrl-names = "default";
>> +     pinctrl-0 = <&dragon_sdcc1_pins>;
>> +     vmmc-supply = <&pm8901_l5>;
>> +     vqmmc-supply = <&pm8901_lvs0>;
>> +};
>
> I think we're following a non-phandle approach to filling out
> board dts files. We didn't follow it that well on 8660 surf,
> probably because it was so basic, but it would be nice to follow
> that style here as well and populate board properties in nodes
> like how gsbi@19c00000 has been done. I'll leave this up to Andy
> though as he's the maintainer here.

Andy? How do you want it? I can do it either way, no big deal for
me.

Yours,
Linus Walleij
Stephen Boyd June 16, 2016, 12:11 a.m. UTC | #3 
On 06/14, Linus Walleij wrote:
> +
> +/ {
> +	model = "Qualcomm APQ8060 Dragonboard";
> +	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
> +
> +	aliases {
> +		serial0 = &gsbi12_serial;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
> +		/* Main power of the board: 3.7V */
> +		vph: regulator-fixed@1 {

So does this mean we shouldn't have the @1 here because there's no
reg property?
diff mbox

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 06b6c2d695bf..793bb14c1329 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -572,6 +572,7 @@  dtb-$(CONFIG_ARCH_PRIMA2) += \
 dtb-$(CONFIG_ARCH_OXNAS) += \
 	wd-mbwe.dtb
 dtb-$(CONFIG_ARCH_QCOM) += \
+	qcom-apq8060-dragonboard.dtb \
 	qcom-apq8064-arrow-db600c.dtb \
 	qcom-apq8064-cm-qs600.dtb \
 	qcom-apq8064-ifc6410.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
new file mode 100644
index 000000000000..734d5e8446db
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -0,0 +1,557 @@ 
+/*
+ * Copyright 2016 Linaro Ltd
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "qcom-msm8660.dtsi"
+
+/ {
+	model = "Qualcomm APQ8060 Dragonboard";
+	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
+
+	aliases {
+		serial0 = &gsbi12_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		/* Main power of the board: 3.7V */
+		vph: regulator-fixed@1 {
+			compatible = "regulator-fixed";
+			regulator-min-microvolt = <3700000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-name = "VPH";
+			regulator-type = "voltage";
+			regulator-always-on;
+			regulator-boot-on;
+		};
+	};
+
+	/* This is a levelshifter for SDCC5 */
+	dragon_vio_txb: txb0104rgyr {
+		compatible = "regulator-fixed";
+		regulator-name = "Dragon SDCC levelshifter";
+		vin-supply = <&pm8058_l14>;
+		regulator-always-on;
+	};
+
+	soc {
+		gsbi@19c00000 {
+			status = "ok";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dragon_serial0_pins>;
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			serial@19c40000 {
+				status = "ok";
+			};
+		};
+	};
+};
+
+/* Intenal 3.69 GiB eMMC */
+&sdcc1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc1_pins>;
+	vmmc-supply = <&pm8901_l5>;
+	vqmmc-supply = <&pm8901_lvs0>;
+};
+
+/* External micro SD card, directly connected, pulled up to 2.85 V */
+&sdcc3 {
+	status = "okay";
+	/* Enable SSBI GPIO 22 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+	cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+};
+
+/*
+ * Second external micro SD card, using two TXB104RGYR levelshifters
+ * to lift from 1.8 V to 2.85 V
+ */
+&sdcc5 {
+	status = "okay";
+	/* Enable SSBI GPIO 26 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+	cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+	vqmmc-supply = <&dragon_vio_txb>;
+};
+
+/* Set up of the PMIC RPM regulators for this board */
+&rpm {
+	/* PM8901 supplies "preliminary regulators" whatever that means */
+	pm8901-regulators {
+		vdd_l0-supply = <&pm8901_s4>;
+		vdd_l1-supply = <&vph>;
+		vdd_l2-supply = <&vph>;
+		vdd_l3-supply = <&vph>;
+		vdd_l4-supply = <&vph>;
+		vdd_l5-supply = <&vph>;
+		vdd_l6-supply = <&vph>;
+		/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		lvs0_in-supply = <&pm8058_s3>;
+		lvs1_in-supply = <&pm8901_s4>;
+		lvs2_in-supply = <&pm8058_l0>;
+		lvs3_in-supply = <&pm8058_s2>;
+		mvs_in-supply = <&pm8058_s3>;
+
+		l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l1 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+		l2 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+		l3 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+		l4 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l6 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
+
+		/* s0 and s1 are SAW regulators controlled over SPM */
+		s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s3 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* LVS0 thru 3 and mvs0 are just switches */
+		lvs0 {
+			regulator-always-on;
+		};
+		lvs1 { };
+		lvs2 { };
+		lvs3 { };
+		mvs0 {};
+	};
+
+	pm8058-regulators {
+		vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+		vdd_l2_l11_l12-supply = <&vph>;
+		vdd_l3_l4_l5-supply = <&vph>;
+		vdd_l6_l7-supply = <&vph>;
+		vdd_l8-supply = <&vph>;
+		vdd_l9-supply = <&vph>;
+		vdd_l10-supply = <&vph>;
+		vdd_l13_l16-supply = <&pm8058_s4>;
+		vdd_l14_l15-supply = <&vph>;
+		vdd_l17_l18-supply = <&vph>;
+		vdd_l19_l20-supply = <&vph>;
+		vdd_l21-supply = <&pm8058_s3>;
+		vdd_l22-supply = <&pm8058_s3>;
+		vdd_l23_l24_l25-supply = <&pm8058_s3>;
+		vdd_s0-supply = <&vph>;
+		vdd_s1-supply = <&vph>;
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		vdd_ncp = <&vph>;
+
+		l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l4 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l6 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3600000>;
+			bias-pull-down;
+		};
+		l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3050000>;
+			bias-pull-down;
+		};
+		l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l10 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l11 {
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			bias-pull-down;
+		};
+		l12 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
+		l13 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			bias-pull-down;
+		};
+		l14 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+		l15 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+		l17 {
+			// 1.5V according to schematic
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l18 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
+		l19 {
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			bias-pull-down;
+		};
+		l20 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l21 {
+			// 1.1 V according to schematic
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+		l22 {
+			// 1.2 V according to schematic
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+		l23 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l24 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l25 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		s0 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1325000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s1 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1250000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s2 {
+			// regulator-min-microvolt = <1200000>;
+			// regulator-max-microvolt = <1400000>;
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+		s4 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		/* LVS0 and LVS1 are just switches */
+		lvs0 {
+			bias-pull-down;
+		};
+		lvs1 {
+			bias-pull-down;
+		};
+
+		ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+	};
+};
+
+&tlmm {
+	/* eMMMC pins, all 8 data lines connected */
+	dragon_sdcc1_pins: sdcc1 {
+		mux {
+			pins = "gpio159", "gpio160", "gpio161",
+			     "gpio162", "gpio163", "gpio164",
+			     "gpio165", "gpio166", "gpio167",
+			     "gpio168";
+			function = "sdc1";
+		};
+		clk {
+			pins = "gpio167"; /* SDC5 CLK */
+			drive-strength = <16>;
+			bias-disable;
+		};
+		cmd {
+			pins = "gpio168"; /* SDC5 CMD */
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data {
+			/* SDC5 D0 to D7 */
+			pins = "gpio159", "gpio160", "gpio161", "gpio162",
+			     "gpio163", "gpio164", "gpio165", "gpio166";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	/*
+	 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+	 * configuration.
+	 */
+	dragon_sdcc3_pins: sdcc3 {
+		clk {
+			pins = "sdc3_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		cmd {
+			pins = "sdc3_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		data {
+			pins = "sdc3_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	/* Second SD card slot pins */
+	dragon_sdcc5_pins: sdcc5 {
+		mux {
+			pins = "gpio95", "gpio96", "gpio97",
+			     "gpio98", "gpio99", "gpio100";
+			function = "sdc5";
+		};
+		clk {
+			pins = "gpio97"; /* SDC5 CLK */
+			drive-strength = <16>;
+			bias-disable;
+		};
+		cmd {
+			pins = "gpio95"; /* SDC5 CMD */
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data {
+			/* SDC5 D0 to D3 */
+			pins = "gpio96", "gpio98", "gpio99", "gpio100";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	/* Primary serial port uart 0 pins */
+	dragon_serial0_pins: gsbi12 {
+		mux {
+			pins = "gpio117", "gpio118";
+			function = "gsbi12";
+		};
+		tx {
+			pins = "gpio117";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		rx {
+			pins = "gpio118";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&pmicintc {
+	keypad@148 {
+		linux,keymap = <
+			MATRIX_KEY(0, 0, KEY_MENU)
+			MATRIX_KEY(0, 2, KEY_1)
+			MATRIX_KEY(0, 3, KEY_4)
+			MATRIX_KEY(0, 4, KEY_7)
+			MATRIX_KEY(1, 0, KEY_UP)
+			MATRIX_KEY(1, 1, KEY_LEFT)
+			MATRIX_KEY(1, 2, KEY_DOWN)
+			MATRIX_KEY(1, 3, KEY_5)
+			MATRIX_KEY(1, 3, KEY_8)
+			MATRIX_KEY(2, 0, KEY_HOME)
+			MATRIX_KEY(2, 1, KEY_REPLY)
+			MATRIX_KEY(2, 2, KEY_2)
+			MATRIX_KEY(2, 3, KEY_6)
+			MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+			MATRIX_KEY(3, 1, KEY_RIGHT)
+			MATRIX_KEY(3, 2, KEY_3)
+			MATRIX_KEY(3, 3, KEY_9)
+			MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+			MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+			MATRIX_KEY(4, 1, KEY_BACK)
+			MATRIX_KEY(4, 2, KEY_CAMERA)
+			MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+			>;
+		keypad,num-rows = <6>;
+		keypad,num-columns = <5>;
+	};
+};
+
+&pm8058_gpio {
+	dragon_sdcc3_gpios: sdcc3-gpios {
+		pinconf {
+			pins = "gpio22";
+			function = "normal";
+			input-enable;
+			bias-pull-up;
+			qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_sdcc5_gpios: sdcc5-gpios {
+		pinconf {
+			pins = "gpio26";
+			function = "normal";
+			input-enable;
+			bias-pull-up;
+			qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+};