@@ -24,6 +24,8 @@
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/clk/at91_pmc.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
#include <asm/irq.h>
#include <linux/atomic.h>
@@ -459,6 +461,68 @@ static void __init at91_pm_init(void (*pm_idle)(void))
pr_info("AT91: PM not supported, due to no SRAM allocated\n");
}
+static int __init at91_pmc_fast_startup_init(void)
+{
+ struct device_node *np, *cnp;
+ struct regmap *regmap;
+ u32 input, input_mask;
+ u32 mode = 0, polarity = 0;
+
+ np = of_find_compatible_node(NULL, NULL,
+ "atmel,sama5d2-pmc-fast-startup");
+ if (!np)
+ return -ENODEV;
+
+ regmap = syscon_node_to_regmap(of_get_parent(np));
+ if (IS_ERR(regmap)) {
+ pr_info("AT91: failed to find PMC fast startup node\n");
+ return PTR_ERR(regmap);
+ }
+
+ for_each_child_of_node(np, cnp) {
+ if (of_property_read_u32(cnp, "reg", &input)) {
+ pr_warn("AT91: reg property is missing for %s\n",
+ cnp->full_name);
+ continue;
+ }
+
+ input_mask = 1 << input;
+ if (!(input_mask & AT91_PMC_FS_INPUT_MASK)) {
+ pr_warn("AT91: wake-up input %d out of range\n", input);
+ continue;
+ }
+ mode |= input_mask;
+
+ if (of_property_read_bool(cnp, "atmel,wakeup-active-high"))
+ polarity |= input_mask;
+ }
+
+ if (of_property_read_bool(np, "atmel,wakeup-rtc-timer"))
+ mode |= AT91_PMC_RTCAL;
+
+ if (of_property_read_bool(np, "atmel,wakeup-usb-resume"))
+ mode |= AT91_PMC_USBAL;
+
+ if (of_property_read_bool(np, "atmel,wakeup-sdmmc-cd"))
+ mode |= AT91_PMC_SDMMC_CD;
+
+ if (of_property_read_bool(np, "atmel,wakeup-rxlp-match"))
+ mode |= AT91_PMC_RXLP_MCE;
+
+ if (of_property_read_bool(np, "atmel,wakeup-acc-comparison"))
+ mode |= AT91_PMC_ACC_CE;
+
+ pr_debug("AT91: mode = 0x%x, ploarity = 0%x\n", mode, polarity);
+
+ regmap_write(regmap, AT91_PMC_FSMR, mode);
+
+ regmap_write(regmap, AT91_PMC_FSPR, polarity);
+
+ of_node_put(np);
+
+ return 0;
+}
+
void __init at91rm9200_pm_init(void)
{
at91_dt_ramc();
@@ -511,4 +575,5 @@ void __init sama5d2_pm_init(void)
sama5_pm_init();
at91_pm_data.ulp_mode = ULP1_MODE;
+ at91_pmc_fast_startup_init();
}
@@ -157,6 +157,20 @@
#define AT91_PMC_GCKRDY (1 << 24) /* Generated Clocks */
#define AT91_PMC_IMR 0x6c /* Interrupt Mask Register */
+#define AT91_PMC_FSMR 0x70 /* Fast Startup Mode Register */
+#define AT91_PMC_FSTT(n) (0x1 << n)
+#define AT91_PMC_RTCAL BIT(17) /* RTC Alarm Enable */
+#define AT91_PMC_USBAL BIT(18) /* USB Resume Enable */
+#define AT91_PMC_SDMMC_CD BIT(19) /* SDMMC Card Detect Enable */
+#define AT91_PMC_LPM BIT(20) /* Low-power Mode */
+#define AT91_PMC_RXLP_MCE BIT(24) /* Backup UART Receive Enable */
+#define AT91_PMC_ACC_CE BIT(25) /* ACC Enable */
+
+#define AT91_PMC_FSPR 0x74 /* Fast Startup Polarity Reg */
+#define AT91_PMC_FSTP(n) (0x1 << n)
+
+#define AT91_PMC_FS_INPUT_MASK 0x7ff
+
#define AT91_PMC_PLLICPR 0x80 /* PLL Charge Pump Current Register */
#define AT91_PMC_PROT 0xe4 /* Write Protect Mode Register [some SAM9] */
The fast startup signal is used as wake up sources for ULP1 mode. As soon as a fast startup signal is asserted, the embedded 12 MHz RC oscillator restarts automatically. This patch is to configure the fast startup signals, which signal is enabled to trigger the PMC to wake up the system from ULP1 mode should be configured via the DT. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> --- Changes in v6: None Changes in v5: - to improve the scalability, rework the DT expression part, use the child nodes to describe the wake-up input and its active level. Changes in v4: None Changes in v3: - use 0 and 1, not string, to define the trigger active polarity. Changes in v2: - shorten the pmc-fast-startup property's name. - use the value property, instead of bool property for high or low triggered. arch/arm/mach-at91/pm.c | 65 ++++++++++++++++++++++++++++++++++++++++++++ include/linux/clk/at91_pmc.h | 14 ++++++++++ 2 files changed, 79 insertions(+)