Message ID | 1480637665-6325-2-git-send-email-sergio.prado@e-labworks.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On 12/02/2016 09:14 AM, Sergio Prado wrote: > Adds the device tree bindings description for Samsung S3C24XX > MMC/SD/SDIO controller, used as a connectivity interface with external > MMC, SD and SDIO storage mediums. > > Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com> > --- > .../devicetree/bindings/mmc/samsung,s3cmci.txt | 38 ++++++++++++++++++++++ > 1 file changed, 38 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt > > diff --git a/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt b/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt > new file mode 100644 > index 000000000000..3f044076e69a > --- /dev/null > +++ b/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt > @@ -0,0 +1,38 @@ > +* Samsung's S3C24XX MMC/SD/SDIO controller device tree bindings > + > +Samsung's S3C24XX MMC/SD/SDIO controller is used as a connectivity interface > +with external MMC, SD and SDIO storage mediums. > + > +This file documents differences between the core mmc properties described by > +mmc.txt and the properties used by the Samsung S3C24XX MMC/SD/SDIO controller > +implementation. > + > +Required SoC Specific Properties: > +- compatible: should be one of the following > + - "samsung,s3c2410-sdi": for controllers compatible with s3c2410 > + - "samsung,s3c2412-sdi": for controllers compatible with s3c2412 > + - "samsung,s3c2440-sdi": for controllers compatible with s3c2440 > +- clocks: Should reference the controller clock > +- clock-names: Should contain "sdi" > + > +Required Board Specific Properties: > +- pinctrl-0: Should specify pin control groups used for this controller. > +- pinctrl-names: Should contain only one value - "default". I'm not sure but i think this description doesn't need at here. > + > +Example: > + sdi: sdi@5a000000 { I think it needs to use "mmc0: sdi@5a000000" instead of "sdi: sdi@5a000000" Because mmc is more clear than sdi. > + compatible = "samsung,s3c2440-sdi"; > + pinctrl-names = "default"; > + pinctrl-0 = <&sdi_pins>; > + reg = <0x5a000000 0x100000>; > + interrupts = <0 0 21 3>; > + clocks = <&clocks PCLK_SDI>; > + clock-names = "sdi"; > + bus-width = <4>; > + cd-gpios = <&gpg 8 GPIO_ACTIVE_LOW>; > + wp-gpios = <&gph 8 GPIO_ACTIVE_LOW>; > + }; > + > + Note: This example shows both SoC specific and board specific properties > + in a single device node. The properties can be actually be separated > + into SoC specific node and board specific node. >
On Fri, Dec 02, 2016 at 09:48:45AM +0900, Jaehoon Chung wrote: > On 12/02/2016 09:14 AM, Sergio Prado wrote: > > Adds the device tree bindings description for Samsung S3C24XX > > MMC/SD/SDIO controller, used as a connectivity interface with external > > MMC, SD and SDIO storage mediums. > > > > Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com> > > --- > > .../devicetree/bindings/mmc/samsung,s3cmci.txt | 38 ++++++++++++++++++++++ > > 1 file changed, 38 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt > > > > diff --git a/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt b/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt > > new file mode 100644 > > index 000000000000..3f044076e69a > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt > > @@ -0,0 +1,38 @@ > > +* Samsung's S3C24XX MMC/SD/SDIO controller device tree bindings > > + > > +Samsung's S3C24XX MMC/SD/SDIO controller is used as a connectivity interface > > +with external MMC, SD and SDIO storage mediums. > > + > > +This file documents differences between the core mmc properties described by > > +mmc.txt and the properties used by the Samsung S3C24XX MMC/SD/SDIO controller > > +implementation. > > + > > +Required SoC Specific Properties: > > +- compatible: should be one of the following > > + - "samsung,s3c2410-sdi": for controllers compatible with s3c2410 > > + - "samsung,s3c2412-sdi": for controllers compatible with s3c2412 > > + - "samsung,s3c2440-sdi": for controllers compatible with s3c2440 > > +- clocks: Should reference the controller clock > > +- clock-names: Should contain "sdi" > > + > > +Required Board Specific Properties: > > +- pinctrl-0: Should specify pin control groups used for this controller. > > +- pinctrl-names: Should contain only one value - "default". > > I'm not sure but i think this description doesn't need at here. > > > + > > +Example: > > + sdi: sdi@5a000000 { > > I think it needs to use "mmc0: sdi@5a000000" instead of "sdi: sdi@5a000000" > Because mmc is more clear than sdi. The label doesn't matter much as it is not part of the dtb. The unit name should be 'mmc' though. With that, Acked-by: Rob Herring <robh@kernel.org>
diff --git a/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt b/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt new file mode 100644 index 000000000000..3f044076e69a --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt @@ -0,0 +1,38 @@ +* Samsung's S3C24XX MMC/SD/SDIO controller device tree bindings + +Samsung's S3C24XX MMC/SD/SDIO controller is used as a connectivity interface +with external MMC, SD and SDIO storage mediums. + +This file documents differences between the core mmc properties described by +mmc.txt and the properties used by the Samsung S3C24XX MMC/SD/SDIO controller +implementation. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c2410-sdi": for controllers compatible with s3c2410 + - "samsung,s3c2412-sdi": for controllers compatible with s3c2412 + - "samsung,s3c2440-sdi": for controllers compatible with s3c2440 +- clocks: Should reference the controller clock +- clock-names: Should contain "sdi" + +Required Board Specific Properties: +- pinctrl-0: Should specify pin control groups used for this controller. +- pinctrl-names: Should contain only one value - "default". + +Example: + sdi: sdi@5a000000 { + compatible = "samsung,s3c2440-sdi"; + pinctrl-names = "default"; + pinctrl-0 = <&sdi_pins>; + reg = <0x5a000000 0x100000>; + interrupts = <0 0 21 3>; + clocks = <&clocks PCLK_SDI>; + clock-names = "sdi"; + bus-width = <4>; + cd-gpios = <&gpg 8 GPIO_ACTIVE_LOW>; + wp-gpios = <&gph 8 GPIO_ACTIVE_LOW>; + }; + + Note: This example shows both SoC specific and board specific properties + in a single device node. The properties can be actually be separated + into SoC specific node and board specific node.
Adds the device tree bindings description for Samsung S3C24XX MMC/SD/SDIO controller, used as a connectivity interface with external MMC, SD and SDIO storage mediums. Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com> --- .../devicetree/bindings/mmc/samsung,s3cmci.txt | 38 ++++++++++++++++++++++ 1 file changed, 38 insertions(+) create mode 100644 Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt