@@ -1960,6 +1960,320 @@ enum v4l2_vp8_golden_frame_sel -
1, 2 and 3 corresponding to encoder profiles 0, 1, 2 and 3.
+HEVC Control Reference
+---------------------
+
+The HEVC controls include controls for encoding parameters of HEVC video
+codec.
+
+
+.. _hevc-control-id:
+
+HEVC Control IDs
+^^^^^^^^^^^^^^^
+
+``V4L2_CID_MPEG_VIDEO_HEVC_MIN_QP``
+ Minimum quantization parameter for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_MAX_QP``
+ Maximum quantization parameter for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_I_FRAME_QP``
+ Quantization parameter for an I frame for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_P_FRAME_QP``
+ Quantization parameter for a P frame for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_B_FRAME_QP``
+ Quantization parameter for a B frame for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_QP_ENABLE``
+ HIERARCHICAL_QP_ENABLE allows host to specify the QP values for each
+ temporal layer through HIERARCHICAL_QP_LAYER. This is valid only if
+ HIERARCHICAL_CODING_LAYER is greater than 1.
+
+.. _v4l2-hevc-hierarchical-coding-type:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_TYPE``
+ (enum)
+
+enum v4l2_mpeg_video_hevc_hier_coding_type -
+ Selects the hierarchical coding type for encoding. Possible values are:
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_B``
+ - Use the B frame for hierarchical coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_P``
+ - Use the P frame for hierarchical coding.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+
+.. _v4l2-hevc-hierarchical-coding-layer:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER``
+ (enum)
+
+enum v4l2_mpeg_video_hevc_hierarchial_coding_layer -
+ Selects the hierarchical coding layer. In normal encoding
+ (non-hierarchial coding), it should be zero. Possible values are:
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHIAL_CODING_LAYER0``
+ - Use the Layer 0 for hierarchial coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHIAL_CODING_LAYER1``
+ - Use the Layer 1 for hierarchial coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHIAL_CODING_LAYER2``
+ - Use the Layer 2 for hierarchial coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHIAL_CODING_LAYER3``
+ - Use the Layer 3 for hierarchial coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHIAL_CODING_LAYER4``
+ - Use the Layer 4 for hierarchial coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHIAL_CODING_LAYER5``
+ - Use the Layer 5 for hierarchial coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHIAL_CODING_LAYER6``
+ - Use the Layer 6 for hierarchial coding.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER_QP``
+ Indicates the hierarchical coding layer quantization parameter.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_PROFILE``
+ Select the desired profile for HEVC encoder.
+ Zero indicates the main profile. One indicates the main still
+ picture profile.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LEVEL``
+ Selects the desired level for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_RC_FRAME_RATE``
+ Selects the RC filter frame rate for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_TIER_FLAG``
+ TIER_FLAG specifies tier information of the HEVC encoded picture.
+ By default selects HEVC tier_flag as Main and setting this flag to one
+ indicates High tier.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_MAX_PARTITION_DEPTH``
+ Selects HEVC Maximum coding unit depth.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_REF_NUMBER_FOR_PFRAMES``
+ Selects number of P reference picture required for HEVC encoder.
+ P-Frame can use 1 or 2 frames for reference.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LF_DISABLE``
+ Disables HEVC loop filter.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LF_SLICE_BOUNDARY``
+ Selects whether to apply the loop filter across the slice boundary or not.
+ If the value is 0, loop filter will not be applied across the slice boundary.
+ If the value is 1, loop filter will be applied across the slice boundary.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LF_BETA_OFFSET_DIV2``
+ Selects HEVC loop filter beta offset. The valid range is [-6, +6].
+ This could be a negative value in the 2's complement expression.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LF_TC_OFFSET_DIV2``
+ Selects HEVC loop filter tc offset. The valid range is [-6, +6].
+ This could be a negative value in the 2's complement expression.
+
+.. _v4l2-hevc-refresh-type:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_REFRESH_TYPE``
+ (enum)
+
+enum v4l2_mpeg_video_hevc_hier_refresh_type -
+ Selects refresh type for HEVC encoder.
+ Host has to specify the period into
+ HEVC_REFRESH_PERIOD.
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_REFRESH_NONE``
+ - Use the B frame for hierarchical coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_REFRESH_CRA``
+ - Use CRA(Clean Random Access Unit) picture encoding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_REFRESH_IDR``
+ - Use IDR picture encoding.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+
+``V4L2_CID_MPEG_VIDEO_HEVC_REFRESH_PERIOD``
+ Selects the refresh period for HEVC encoder.
+ This specifies the number of I picture between two CRA/IDR pictures.
+ This is valid only if REFRESH_TYPE is not 0.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LOSSLESS_CU_ENABLE``
+ Selects HEVC lossless encoding.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_CONST_INTRA_PRED_ENABLE``
+ Enables constant intra prediction for HEVC encoder.
+ Specifies the constrained intra prediction in which intra LCU prediction is performed.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_WAVEFRONT_ENABLE``
+ Enables wavefront for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LTR_ENABLE``
+ Specifies which encoded frame use short term or long term as reference.
+ Zero indicates use only short term reference. One indicates use short term
+ reference and long term reference.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_USE_REF``
+ Specifies which current frame is encoded by referencing as long term
+ reference frame. Zero indicates short term reference frame is used.
+ One indicates long term reference idx 0 is used. Two indicates long term
+ reference idx 1 is used. Three indicates use the nearest longest term
+ reference from current frame. It is valid only when LTR_ENABLE is enabled.
+ Both long term references bits can be selected simulatenously and MFC will
+ select the best long term refernece among them based on the POC which is
+ nearest the current frame.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_STORE_REF``
+ Specifies whether the current frame needs to be stored as long term
+ reference frame. Zero indicates store in short term reference frame.
+ One indicates store in long_term_reference_frame_idx 0. Two indicates
+ store in long_term_frame_idx 1. It is valid only when LTR_ENABLE is enabled.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_SIGN_DATA_HIDING``
+ Enable sign data hiding for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_GENERAL_PB_ENABLE``
+ Enable general picture buffers for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_TEMPORAL_ID_ENABLE``
+ Enable temporal identifier for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_STRONG_SMOTHING_FLAG``
+ Enable HEVC Strong intra smoothing.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_MAX_NUM_MERGE_MV_MINUS1``
+ Indicates max number of merge candidate motion vectors.
+ Values is from zero to four.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_ADAPTIVE_RC_DARK``
+ Indicates HEVC dark region adaptive.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_ADAPTIVE_RC_SMOOTH``
+ Indicates HEVC smooth region adaptive.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_ADAPTIVE_RC_STATIC``
+ Indicates HEVC static region adaptive.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_ADAPTIVE_RC_ACTIVITY``
+ Indicates HEVC activity adaptive.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_DISABLE_INTRA_PU_SPLIT``
+ Disables intra pu split for HEVC Encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_DISABLE_TMV_PREDICTION``
+ Disables tmv prediction for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_WITHOUT_STARTCODE_ENABLE``
+ Specifies if MFC generates a stream with a size of length field instead of
+ start code pattern. The size of the length field is configurable among 1,2
+ or 4 thorugh the SIZE_OF_LENGHT_FIELD. It is not applied at SEQ_START.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_QP_INDEX_CR``
+ Indicates the quantization parameter CR index.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_QP_INDEX_CB``
+ Indicates the quantization parameter CB index.
+
+.. _v4l2-hevc-size-of-length-field:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_SIZE_OF_LENGTH_FIELD``
+(enum)
+
+enum v4l2_mpeg_video_hevc_size_of_length_field -
+ Indicates the size of length field.
+ This is valid when encoding WITHOUT_STARTCODE_ENABLE is enabled.
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_SIZE_0``
+ - Generate start code pattern (Normal).
+ * - ``V4L2_MPEG_VIDEO_HEVC_SIZE_1``
+ - Generate size of length field instead of start code pattern and length is 1.
+ * - ``V4L2_MPEG_VIDEO_HEVC_SIZE_2``
+ - Generate size of length field instead of start code pattern and length is 2.
+ * - ``V4L2_MPEG_VIDEO_HEVC_SIZE_4``
+ - Generate size of length field instead of start code pattern and length is 4.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+``V4L2_CID_MPEG_VIDEO_HEVC_PREPEND_SPSPPS_TO_IDR``
+ Indicates prepend SPS/PPS to every IDR.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER_CH``
+ Indicates hierarchical coding layer change for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER_BIT0``
+ Indicates hierarchical coding layer BIT0 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER_BIT1``
+ Indicates hierarchical coding layer BIT1 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER_BIT2``
+ Indicates hierarchical coding layer BIT2 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER_BIT3``
+ Indicates hierarchical coding layer BIT3 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER_BIT4``
+ Indicates hierarchical coding layer BIT4 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER_BIT5``
+ Indicates hierarchical coding layer BIT5 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_LAYER_BIT6``
+ Indicates hierarchical coding layer BIT6 for HEVC encoder.
+
+
.. _camera-controls:
Camera Control Reference
Added V4l2 controls for HEVC encoder Signed-off-by: Smitha T Murthy <smitha.t@samsung.com> --- Documentation/media/uapi/v4l/extended-controls.rst | 314 ++++++++++++++++++++ 1 files changed, 314 insertions(+), 0 deletions(-)