diff mbox

[V10,4/6] ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point

Message ID 1488583129-4159-5-git-send-email-stefan.wahren@i2se.com (mailing list archive)
State New, archived
Headers show

Commit Message

Stefan Wahren March 3, 2017, 11:18 p.m. UTC
As suggested by Eduardo Valentin this adds the thermal zone for
the bcm2835 SoC with its single thermal sensor. We start with
the criticial trip point and leave the cooling devices empty
since we don't have any at the moment. Since the coefficients
could vary depending on the SoC we need to define them separate.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
 arch/arm/boot/dts/bcm2835.dtsi |    4 ++++
 arch/arm/boot/dts/bcm2836.dtsi |    4 ++++
 arch/arm/boot/dts/bcm283x.dtsi |   21 +++++++++++++++++++++
 3 files changed, 29 insertions(+)
diff mbox

Patch

diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi
index 0890d97..659b6e9 100644
--- a/arch/arm/boot/dts/bcm2835.dtsi
+++ b/arch/arm/boot/dts/bcm2835.dtsi
@@ -24,6 +24,10 @@ 
 	};
 };
 
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
 /* enable thermal sensor with the correct compatible property set */
 &thermal {
 	compatible = "brcm,bcm2835-thermal";
diff --git a/arch/arm/boot/dts/bcm2836.dtsi b/arch/arm/boot/dts/bcm2836.dtsi
index 519a44f..da3deeb 100644
--- a/arch/arm/boot/dts/bcm2836.dtsi
+++ b/arch/arm/boot/dts/bcm2836.dtsi
@@ -77,6 +77,10 @@ 
 	interrupts = <8>;
 };
 
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
 /* enable thermal sensor with the correct compatible property set */
 &thermal {
 	compatible = "brcm,bcm2836-thermal";
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index a3106aa..9bc0a1c9 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -19,6 +19,26 @@ 
 		bootargs = "earlyprintk console=ttyAMA0";
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <80000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+
+			cooling-maps {
+			};
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -394,6 +414,7 @@ 
 			compatible = "brcm,bcm2835-thermal";
 			reg = <0x7e212000 0x8>;
 			clocks = <&clocks BCM2835_CLOCK_TSENS>;
+			#thermal-sensor-cells = <0>;
 			status = "disabled";
 		};