diff mbox

[v11,3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board

Message ID 1488937357-5623-4-git-send-email-hoegeun.kwon@samsung.com (mailing list archive)
State New, archived
Headers show

Commit Message

Hoegeun Kwon March 8, 2017, 1:42 a.m. UTC
From: Hyungwon Hwang <human.hwang@samsung.com>

This patch add the panel device tree node for S6E3HA2 display
controller to TM2 dts.

Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
---
 arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

Comments

Krzysztof Kozlowski March 8, 2017, 6:47 a.m. UTC | #1
On Wed, Mar 08, 2017 at 10:42:37AM +0900, Hoegeun Kwon wrote:
> From: Hyungwon Hwang <human.hwang@samsung.com>
> 
> This patch add the panel device tree node for S6E3HA2 display
> controller to TM2 dts.
> 
> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
> Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
> ---
>  arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 12 ++++++++++++
>  1 file changed, 12 insertions(+)
> 

Thanks, applied.

Best regards,
Krzysztof
diff mbox

Patch

diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
index dea0a6f..db3fed2 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
@@ -52,6 +52,18 @@ 
 	assigned-clock-rates = <250000000>, <400000000>;
 };
 
+&dsi {
+	panel@0 {
+		compatible = "samsung,s6e3ha2";
+		reg = <0>;
+		vdd3-supply = <&ldo27_reg>;
+		vci-supply = <&ldo28_reg>;
+		reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
+		te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
+	};
+};
+
 &hsi2c_9 {
 	status = "okay";