diff mbox

[2/2] arm64: marvell: dts: add second 1G port on the Armada 8040 DB

Message ID 1494890913-8360-3-git-send-email-mw@semihalf.com (mailing list archive)
State New, archived
Headers show

Commit Message

Marcin Wojtas May 15, 2017, 11:28 p.m. UTC
Armada 8040 DB is equipped with 4 (2x 10G SFI + 2x 1G RGMII)
ethernet ports of which only one was hitherto enabled.
Because currently mvpp2 driver is capable of supporting only
1G RGMII/SGMII, enable second port from CP slave HW block.

Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
 arch/arm64/boot/dts/marvell/armada-8040-db.dts | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

Comments

Gregory CLEMENT May 23, 2017, 2:24 p.m. UTC | #1
Hi Marcin,
 
 On mar., mai 16 2017, Marcin Wojtas <mw@semihalf.com> wrote:

> Armada 8040 DB is equipped with 4 (2x 10G SFI + 2x 1G RGMII)
> ethernet ports of which only one was hitherto enabled.
> Because currently mvpp2 driver is capable of supporting only
> 1G RGMII/SGMII, enable second port from CP slave HW block.
>

Applied on mvebu/dt64

Thanks,

Gregory

> Signed-off-by: Marcin Wojtas <mw@semihalf.com>
> ---
>  arch/arm64/boot/dts/marvell/armada-8040-db.dts | 16 ++++++++++++++++
>  1 file changed, 16 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-8040-db.dts b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
> index dc0d084..3cde649 100644
> --- a/arch/arm64/boot/dts/marvell/armada-8040-db.dts
> +++ b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
> @@ -169,6 +169,22 @@
>  	status = "okay";
>  };
>  
> +&cps_mdio {
> +	phy0: ethernet-phy@0 {
> +		reg = <0>;
> +	};
> +};
> +
> +&cps_ethernet {
> +	status = "okay";
> +};
> +
> +&cps_eth1 {
> +	status = "okay";
> +	phy = <&phy0>;
> +	phy-mode = "rgmii-id";
> +};
> +
>  &ap_sdhci0 {
>  	status = "okay";
>  	bus-width = <4>;
> -- 
> 1.8.3.1
>
diff mbox

Patch

diff --git a/arch/arm64/boot/dts/marvell/armada-8040-db.dts b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
index dc0d084..3cde649 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
@@ -169,6 +169,22 @@ 
 	status = "okay";
 };
 
+&cps_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&cps_ethernet {
+	status = "okay";
+};
+
+&cps_eth1 {
+	status = "okay";
+	phy = <&phy0>;
+	phy-mode = "rgmii-id";
+};
+
 &ap_sdhci0 {
 	status = "okay";
 	bus-width = <4>;