diff mbox

[2/3] arm64: allwinner: h5: Add initial Orangepi Prime support

Message ID 1495740382-9061-2-git-send-email-jteki@openedev.com (mailing list archive)
State New, archived
Headers show

Commit Message

Jagan Teki May 25, 2017, 7:26 p.m. UTC
From: Jagan Teki <jagan@amarulasolutions.com>

Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT

http://www.orangepi.org/OrangePiPrime/

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
 arch/arm64/boot/dts/allwinner/Makefile             |   1 +
 .../dts/allwinner/sun50i-h5-orangepi-prime.dts     | 100 +++++++++++++++++++++
 2 files changed, 101 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts

Comments

Icenowy Zheng May 26, 2017, 4:40 p.m. UTC | #1
在 2017-05-26 03:26,Jagan Teki 写道:
> From: Jagan Teki <jagan@amarulasolutions.com>
> 
> Orangepi Prime is an open-source single-board computer
> using the Allwinner h5 SOC.

Sorry but I have already added this board and it's
scheduled at 4.13.

> 
> H5 Orangepi Prime has
> - Quad-core Cortex-A53
> - 2GB DDR3
> - Debug TTL UART
> - 1000M/100M Ethernet RJ45
> - Three USB 2.0
> - HDMI
> - Audio and MIC
> - Wifi + BT
> - IR receiver
> - HDMI
> - Wifi + BT
> 
> http://www.orangepi.org/OrangePiPrime/
> 
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
>  arch/arm64/boot/dts/allwinner/Makefile             |   1 +
>  .../dts/allwinner/sun50i-h5-orangepi-prime.dts     | 100 
> +++++++++++++++++++++
>  2 files changed, 101 insertions(+)
>  create mode 100644 
> arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
> 
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile
> b/arch/arm64/boot/dts/allwinner/Makefile
> index 4120ce9..bf7d3fe 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -2,6 +2,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb 
> sun50i-a64-pine64.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
> 
>  always		:= $(dtb-y)
>  subdir-y	:= $(dts-dirs)
> diff --git
> a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
> b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
> new file mode 100644
> index 0000000..9e98aac
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
> @@ -0,0 +1,100 @@
> +/*
> + * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This library is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of 
> the
> + *     License, or (at your option) any later version.
> + *
> + *     This library is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h5.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	model = "OrangePi Prime";
> +	compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory {
> +		reg = <0x40000000 0x80000000>;
> +	};
> +
> +	soc {
> +		reg_vcc3v3: vcc3v3 {
> +			compatible = "regulator-fixed";
> +			regulator-name = "vcc3v3";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +		};
> +	};
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <4>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins_a>;
> +	status = "okay";
> +};
> +
> +&usbphy {
> +	status = "okay";
> +};
> +
> +&ohci1 {
> +	status = "okay";
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> --
> 1.9.1
Jagan Teki May 26, 2017, 4:44 p.m. UTC | #2
On Fri, May 26, 2017 at 10:10 PM,  <icenowy@aosc.io> wrote:
> 在 2017-05-26 03:26,Jagan Teki 写道:
>>
>> From: Jagan Teki <jagan@amarulasolutions.com>
>>
>> Orangepi Prime is an open-source single-board computer
>> using the Allwinner h5 SOC.
>
>
> Sorry but I have already added this board and it's
> scheduled at 4.13.

Ohh, unfortunately I missed to find it on ML, can you point?

thanks!
Icenowy Zheng May 26, 2017, 4:51 p.m. UTC | #3
在 2017-05-27 00:44,Jagan Teki 写道:
> On Fri, May 26, 2017 at 10:10 PM,  <icenowy@aosc.io> wrote:
>> 在 2017-05-26 03:26,Jagan Teki 写道:
>>> 
>>> From: Jagan Teki <jagan@amarulasolutions.com>
>>> 
>>> Orangepi Prime is an open-source single-board computer
>>> using the Allwinner h5 SOC.
>> 
>> 
>> Sorry but I have already added this board and it's
>> scheduled at 4.13.
> 
> Ohh, unfortunately I missed to find it on ML, can you point?

http://lists.infradead.org/pipermail/linux-arm-kernel/2017-April/501311.html

> 
> thanks!
diff mbox

Patch

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 4120ce9..bf7d3fe 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -2,6 +2,7 @@  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
 
 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
new file mode 100644
index 0000000..9e98aac
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
@@ -0,0 +1,100 @@ 
+/*
+ * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "OrangePi Prime";
+	compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	soc {
+		reg_vcc3v3: vcc3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "vcc3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};