| Message ID | 1508247827-31741-1-git-send-email-pierre-yves.mordret@st.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
+Arnd since it should also fix 64 bits division issue 2017-10-17 15:43 GMT+02:00 Pierre-Yves MORDRET <pierre-yves.mordret@st.com>: > If source and destination bus width differs pack/unpack MDMA > feature has to be activated for alignment. > This pack/unpack feature implies to have both source/destination address > and buffer length aligned on bus width. > > Fixes: a4ffb13c8946 ("dmaengine: Add STM32 MDMA driver") > Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> > --- > drivers/dma/stm32-mdma.c | 84 ++++++++++++++++++++++++++++-------------------- > 1 file changed, 50 insertions(+), 34 deletions(-) > > diff --git a/drivers/dma/stm32-mdma.c b/drivers/dma/stm32-mdma.c > index d3be6bf..daa1602 100644 > --- a/drivers/dma/stm32-mdma.c > +++ b/drivers/dma/stm32-mdma.c > @@ -387,14 +387,20 @@ static int stm32_mdma_get_width(struct stm32_mdma_chan *chan, > } > } > > -static enum dma_slave_buswidth stm32_mdma_get_max_width(u32 buf_len, u32 tlen) > +static enum dma_slave_buswidth stm32_mdma_get_max_width(dma_addr_t addr, > + u32 buf_len, u32 tlen) > { > enum dma_slave_buswidth max_width = DMA_SLAVE_BUSWIDTH_8_BYTES; > > for (max_width = DMA_SLAVE_BUSWIDTH_8_BYTES; > max_width > DMA_SLAVE_BUSWIDTH_1_BYTE; > max_width >>= 1) { > - if (((buf_len % max_width) == 0) && (tlen >= max_width)) > + /* > + * Address and buffer length both have to be aligned on > + * bus width > + */ > + if ((((buf_len | addr) & (max_width - 1)) == 0) && > + tlen >= max_width) > break; > } > > @@ -486,7 +492,8 @@ static void stm32_mdma_set_bus(struct stm32_mdma_device *dmadev, u32 *ctbr, > static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > enum dma_transfer_direction direction, > u32 *mdma_ccr, u32 *mdma_ctcr, > - u32 *mdma_ctbr, u32 buf_len) > + u32 *mdma_ctbr, dma_addr_t addr, > + u32 buf_len) > { > struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); > struct stm32_mdma_chan_config *chan_config = &chan->chan_config; > @@ -520,6 +527,9 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > ctcr &= ~STM32_MDMA_CTCR_LEN2_MSK; > ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1)); > > + /* Disable Pack Enable */ > + ctcr &= ~STM32_MDMA_CTCR_PKE; > + > /* Check burst size constraints */ > if (src_maxburst * src_addr_width > STM32_MDMA_MAX_BURST || > dst_maxburst * dst_addr_width > STM32_MDMA_MAX_BURST) { > @@ -551,6 +561,8 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > > switch (direction) { > case DMA_MEM_TO_DEV: > + dst_addr = chan->dma_config.dst_addr; > + > /* Set device data size */ > dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width); > if (dst_bus_width < 0) > @@ -567,7 +579,7 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst))); > > /* Set memory data size */ > - src_addr_width = stm32_mdma_get_max_width(buf_len, tlen); > + src_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen); > chan->mem_width = src_addr_width; > src_bus_width = stm32_mdma_get_width(chan, src_addr_width); > if (src_bus_width < 0) > @@ -587,15 +599,19 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst))); > > /* Select bus */ > - dst_addr = chan->dma_config.dst_addr; > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, > dst_addr); > > + if (dst_bus_width != src_bus_width) > + ctcr |= STM32_MDMA_CTCR_PKE; > + > /* Set destination address */ > stm32_mdma_write(dmadev, STM32_MDMA_CDAR(chan->id), dst_addr); > break; > > case DMA_DEV_TO_MEM: > + src_addr = chan->dma_config.src_addr; > + > /* Set device data size */ > src_bus_width = stm32_mdma_get_width(chan, src_addr_width); > if (src_bus_width < 0) > @@ -611,7 +627,7 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst))); > > /* Set memory data size */ > - dst_addr_width = stm32_mdma_get_max_width(buf_len, tlen); > + dst_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen); > chan->mem_width = dst_addr_width; > dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width); > if (dst_bus_width < 0) > @@ -630,10 +646,12 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst))); > > /* Select bus */ > - src_addr = chan->dma_config.src_addr; > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, > src_addr); > > + if (dst_bus_width != src_bus_width) > + ctcr |= STM32_MDMA_CTCR_PKE; > + > /* Set source address */ > stm32_mdma_write(dmadev, STM32_MDMA_CSAR(chan->id), src_addr); > break; > @@ -719,23 +737,27 @@ static int stm32_mdma_setup_xfer(struct stm32_mdma_chan *chan, > return -EINVAL; > } > > - ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, > - &ctbr, sg_dma_len(sg)); > - if (ret < 0) > - return ret; > - > if (direction == DMA_MEM_TO_DEV) { > src_addr = sg_dma_address(sg); > dst_addr = dma_config->dst_addr; > + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, > + &ctcr, &ctbr, src_addr, > + sg_dma_len(sg)); > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, > src_addr); > } else { > src_addr = dma_config->src_addr; > dst_addr = sg_dma_address(sg); > + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, > + &ctcr, &ctbr, dst_addr, > + sg_dma_len(sg)); > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, > dst_addr); > } > > + if (ret < 0) > + return ret; > + > stm32_mdma_setup_hwdesc(chan, desc, direction, i, src_addr, > dst_addr, sg_dma_len(sg), ctcr, ctbr, > i == sg_len - 1, i == 0, false); > @@ -830,27 +852,29 @@ stm32_mdma_prep_dma_cyclic(struct dma_chan *c, dma_addr_t buf_addr, > if (!desc) > return NULL; > > - ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, &ctbr, > - period_len); > - if (ret < 0) > - goto xfer_setup_err; > - > - /* Enable interrupts */ > - ccr &= ~STM32_MDMA_CCR_IRQ_MASK; > - ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE | STM32_MDMA_CCR_BTIE; > - desc->ccr = ccr; > - > /* Select bus */ > if (direction == DMA_MEM_TO_DEV) { > src_addr = buf_addr; > + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, > + &ctbr, src_addr, period_len); > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, > src_addr); > } else { > dst_addr = buf_addr; > + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, > + &ctbr, dst_addr, period_len); > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, > dst_addr); > } > > + if (ret < 0) > + goto xfer_setup_err; > + > + /* Enable interrupts */ > + ccr &= ~STM32_MDMA_CCR_IRQ_MASK; > + ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE | STM32_MDMA_CCR_BTIE; > + desc->ccr = ccr; > + > /* Configure hwdesc list */ > for (i = 0; i < count; i++) { > if (direction == DMA_MEM_TO_DEV) { > @@ -956,9 +980,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, > ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1)); > > /* Set source best burst size */ > - max_width = stm32_mdma_get_max_width(len, tlen); > - if (src % max_width) > - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; > + max_width = stm32_mdma_get_max_width(src, len, tlen); > src_bus_width = stm32_mdma_get_width(chan, max_width); > > max_burst = tlen / max_width; > @@ -971,9 +993,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, > STM32_MDMA_CTCR_SINCOS(src_bus_width); > > /* Set destination best burst size */ > - max_width = stm32_mdma_get_max_width(len, tlen); > - if (dest % max_width) > - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; > + max_width = stm32_mdma_get_max_width(dest, len, tlen); > dst_bus_width = stm32_mdma_get_width(chan, max_width); > > max_burst = tlen / max_width; > @@ -1014,9 +1034,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, > STM32_MDMA_MAX_BLOCK_LEN); > > /* Set source best burst size */ > - max_width = stm32_mdma_get_max_width(len, tlen); > - if (src % max_width) > - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; > + max_width = stm32_mdma_get_max_width(src, len, tlen); > src_bus_width = stm32_mdma_get_width(chan, max_width); > > max_burst = tlen / max_width; > @@ -1030,9 +1048,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, > STM32_MDMA_CTCR_SINCOS(src_bus_width); > > /* Set destination best burst size */ > - max_width = stm32_mdma_get_max_width(len, tlen); > - if (dest % max_width) > - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; > + max_width = stm32_mdma_get_max_width(dest, len, tlen); > dst_bus_width = stm32_mdma_get_width(chan, max_width); > > max_burst = tlen / max_width; > -- > 2.7.4 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Tue, Oct 17, 2017 at 04:26:50PM +0200, Benjamin Gaignard wrote: > +Arnd since it should also fix 64 bits division issue Arnd would be back from Prague, so would like to get an ack before I apply... > > 2017-10-17 15:43 GMT+02:00 Pierre-Yves MORDRET <pierre-yves.mordret@st.com>: > > If source and destination bus width differs pack/unpack MDMA > > feature has to be activated for alignment. > > This pack/unpack feature implies to have both source/destination address > > and buffer length aligned on bus width. > > > > Fixes: a4ffb13c8946 ("dmaengine: Add STM32 MDMA driver") > > Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> > > --- > > drivers/dma/stm32-mdma.c | 84 ++++++++++++++++++++++++++++-------------------- > > 1 file changed, 50 insertions(+), 34 deletions(-) > > > > diff --git a/drivers/dma/stm32-mdma.c b/drivers/dma/stm32-mdma.c > > index d3be6bf..daa1602 100644 > > --- a/drivers/dma/stm32-mdma.c > > +++ b/drivers/dma/stm32-mdma.c > > @@ -387,14 +387,20 @@ static int stm32_mdma_get_width(struct stm32_mdma_chan *chan, > > } > > } > > > > -static enum dma_slave_buswidth stm32_mdma_get_max_width(u32 buf_len, u32 tlen) > > +static enum dma_slave_buswidth stm32_mdma_get_max_width(dma_addr_t addr, > > + u32 buf_len, u32 tlen) > > { > > enum dma_slave_buswidth max_width = DMA_SLAVE_BUSWIDTH_8_BYTES; > > > > for (max_width = DMA_SLAVE_BUSWIDTH_8_BYTES; > > max_width > DMA_SLAVE_BUSWIDTH_1_BYTE; > > max_width >>= 1) { > > - if (((buf_len % max_width) == 0) && (tlen >= max_width)) > > + /* > > + * Address and buffer length both have to be aligned on > > + * bus width > > + */ > > + if ((((buf_len | addr) & (max_width - 1)) == 0) && > > + tlen >= max_width) > > break; > > } > > > > @@ -486,7 +492,8 @@ static void stm32_mdma_set_bus(struct stm32_mdma_device *dmadev, u32 *ctbr, > > static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > > enum dma_transfer_direction direction, > > u32 *mdma_ccr, u32 *mdma_ctcr, > > - u32 *mdma_ctbr, u32 buf_len) > > + u32 *mdma_ctbr, dma_addr_t addr, > > + u32 buf_len) > > { > > struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); > > struct stm32_mdma_chan_config *chan_config = &chan->chan_config; > > @@ -520,6 +527,9 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > > ctcr &= ~STM32_MDMA_CTCR_LEN2_MSK; > > ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1)); > > > > + /* Disable Pack Enable */ > > + ctcr &= ~STM32_MDMA_CTCR_PKE; > > + > > /* Check burst size constraints */ > > if (src_maxburst * src_addr_width > STM32_MDMA_MAX_BURST || > > dst_maxburst * dst_addr_width > STM32_MDMA_MAX_BURST) { > > @@ -551,6 +561,8 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > > > > switch (direction) { > > case DMA_MEM_TO_DEV: > > + dst_addr = chan->dma_config.dst_addr; > > + > > /* Set device data size */ > > dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width); > > if (dst_bus_width < 0) > > @@ -567,7 +579,7 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > > ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst))); > > > > /* Set memory data size */ > > - src_addr_width = stm32_mdma_get_max_width(buf_len, tlen); > > + src_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen); > > chan->mem_width = src_addr_width; > > src_bus_width = stm32_mdma_get_width(chan, src_addr_width); > > if (src_bus_width < 0) > > @@ -587,15 +599,19 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > > ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst))); > > > > /* Select bus */ > > - dst_addr = chan->dma_config.dst_addr; > > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, > > dst_addr); > > > > + if (dst_bus_width != src_bus_width) > > + ctcr |= STM32_MDMA_CTCR_PKE; > > + > > /* Set destination address */ > > stm32_mdma_write(dmadev, STM32_MDMA_CDAR(chan->id), dst_addr); > > break; > > > > case DMA_DEV_TO_MEM: > > + src_addr = chan->dma_config.src_addr; > > + > > /* Set device data size */ > > src_bus_width = stm32_mdma_get_width(chan, src_addr_width); > > if (src_bus_width < 0) > > @@ -611,7 +627,7 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > > ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst))); > > > > /* Set memory data size */ > > - dst_addr_width = stm32_mdma_get_max_width(buf_len, tlen); > > + dst_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen); > > chan->mem_width = dst_addr_width; > > dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width); > > if (dst_bus_width < 0) > > @@ -630,10 +646,12 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, > > ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst))); > > > > /* Select bus */ > > - src_addr = chan->dma_config.src_addr; > > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, > > src_addr); > > > > + if (dst_bus_width != src_bus_width) > > + ctcr |= STM32_MDMA_CTCR_PKE; > > + > > /* Set source address */ > > stm32_mdma_write(dmadev, STM32_MDMA_CSAR(chan->id), src_addr); > > break; > > @@ -719,23 +737,27 @@ static int stm32_mdma_setup_xfer(struct stm32_mdma_chan *chan, > > return -EINVAL; > > } > > > > - ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, > > - &ctbr, sg_dma_len(sg)); > > - if (ret < 0) > > - return ret; > > - > > if (direction == DMA_MEM_TO_DEV) { > > src_addr = sg_dma_address(sg); > > dst_addr = dma_config->dst_addr; > > + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, > > + &ctcr, &ctbr, src_addr, > > + sg_dma_len(sg)); > > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, > > src_addr); > > } else { > > src_addr = dma_config->src_addr; > > dst_addr = sg_dma_address(sg); > > + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, > > + &ctcr, &ctbr, dst_addr, > > + sg_dma_len(sg)); > > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, > > dst_addr); > > } > > > > + if (ret < 0) > > + return ret; > > + > > stm32_mdma_setup_hwdesc(chan, desc, direction, i, src_addr, > > dst_addr, sg_dma_len(sg), ctcr, ctbr, > > i == sg_len - 1, i == 0, false); > > @@ -830,27 +852,29 @@ stm32_mdma_prep_dma_cyclic(struct dma_chan *c, dma_addr_t buf_addr, > > if (!desc) > > return NULL; > > > > - ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, &ctbr, > > - period_len); > > - if (ret < 0) > > - goto xfer_setup_err; > > - > > - /* Enable interrupts */ > > - ccr &= ~STM32_MDMA_CCR_IRQ_MASK; > > - ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE | STM32_MDMA_CCR_BTIE; > > - desc->ccr = ccr; > > - > > /* Select bus */ > > if (direction == DMA_MEM_TO_DEV) { > > src_addr = buf_addr; > > + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, > > + &ctbr, src_addr, period_len); > > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, > > src_addr); > > } else { > > dst_addr = buf_addr; > > + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, > > + &ctbr, dst_addr, period_len); > > stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, > > dst_addr); > > } > > > > + if (ret < 0) > > + goto xfer_setup_err; > > + > > + /* Enable interrupts */ > > + ccr &= ~STM32_MDMA_CCR_IRQ_MASK; > > + ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE | STM32_MDMA_CCR_BTIE; > > + desc->ccr = ccr; > > + > > /* Configure hwdesc list */ > > for (i = 0; i < count; i++) { > > if (direction == DMA_MEM_TO_DEV) { > > @@ -956,9 +980,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, > > ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1)); > > > > /* Set source best burst size */ > > - max_width = stm32_mdma_get_max_width(len, tlen); > > - if (src % max_width) > > - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; > > + max_width = stm32_mdma_get_max_width(src, len, tlen); > > src_bus_width = stm32_mdma_get_width(chan, max_width); > > > > max_burst = tlen / max_width; > > @@ -971,9 +993,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, > > STM32_MDMA_CTCR_SINCOS(src_bus_width); > > > > /* Set destination best burst size */ > > - max_width = stm32_mdma_get_max_width(len, tlen); > > - if (dest % max_width) > > - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; > > + max_width = stm32_mdma_get_max_width(dest, len, tlen); > > dst_bus_width = stm32_mdma_get_width(chan, max_width); > > > > max_burst = tlen / max_width; > > @@ -1014,9 +1034,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, > > STM32_MDMA_MAX_BLOCK_LEN); > > > > /* Set source best burst size */ > > - max_width = stm32_mdma_get_max_width(len, tlen); > > - if (src % max_width) > > - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; > > + max_width = stm32_mdma_get_max_width(src, len, tlen); > > src_bus_width = stm32_mdma_get_width(chan, max_width); > > > > max_burst = tlen / max_width; > > @@ -1030,9 +1048,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, > > STM32_MDMA_CTCR_SINCOS(src_bus_width); > > > > /* Set destination best burst size */ > > - max_width = stm32_mdma_get_max_width(len, tlen); > > - if (dest % max_width) > > - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; > > + max_width = stm32_mdma_get_max_width(dest, len, tlen); > > dst_bus_width = stm32_mdma_get_width(chan, max_width); > > > > max_burst = tlen / max_width; > > -- > > 2.7.4 > > > > > > _______________________________________________ > > linux-arm-kernel mailing list > > linux-arm-kernel@lists.infradead.org > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel > > > > -- > Benjamin Gaignard > > Graphic Study Group > > Linaro.org │ Open source software for ARM SoCs > > Follow Linaro: Facebook | Twitter | Blog > -- > To unsubscribe from this list: send the line "unsubscribe dmaengine" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, Oct 17, 2017 at 03:43:47PM +0200, Pierre-Yves MORDRET wrote: > If source and destination bus width differs pack/unpack MDMA > feature has to be activated for alignment. > This pack/unpack feature implies to have both source/destination address > and buffer length aligned on bus width. Applied, thanks
diff --git a/drivers/dma/stm32-mdma.c b/drivers/dma/stm32-mdma.c index d3be6bf..daa1602 100644 --- a/drivers/dma/stm32-mdma.c +++ b/drivers/dma/stm32-mdma.c @@ -387,14 +387,20 @@ static int stm32_mdma_get_width(struct stm32_mdma_chan *chan, } } -static enum dma_slave_buswidth stm32_mdma_get_max_width(u32 buf_len, u32 tlen) +static enum dma_slave_buswidth stm32_mdma_get_max_width(dma_addr_t addr, + u32 buf_len, u32 tlen) { enum dma_slave_buswidth max_width = DMA_SLAVE_BUSWIDTH_8_BYTES; for (max_width = DMA_SLAVE_BUSWIDTH_8_BYTES; max_width > DMA_SLAVE_BUSWIDTH_1_BYTE; max_width >>= 1) { - if (((buf_len % max_width) == 0) && (tlen >= max_width)) + /* + * Address and buffer length both have to be aligned on + * bus width + */ + if ((((buf_len | addr) & (max_width - 1)) == 0) && + tlen >= max_width) break; } @@ -486,7 +492,8 @@ static void stm32_mdma_set_bus(struct stm32_mdma_device *dmadev, u32 *ctbr, static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, enum dma_transfer_direction direction, u32 *mdma_ccr, u32 *mdma_ctcr, - u32 *mdma_ctbr, u32 buf_len) + u32 *mdma_ctbr, dma_addr_t addr, + u32 buf_len) { struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); struct stm32_mdma_chan_config *chan_config = &chan->chan_config; @@ -520,6 +527,9 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, ctcr &= ~STM32_MDMA_CTCR_LEN2_MSK; ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1)); + /* Disable Pack Enable */ + ctcr &= ~STM32_MDMA_CTCR_PKE; + /* Check burst size constraints */ if (src_maxburst * src_addr_width > STM32_MDMA_MAX_BURST || dst_maxburst * dst_addr_width > STM32_MDMA_MAX_BURST) { @@ -551,6 +561,8 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, switch (direction) { case DMA_MEM_TO_DEV: + dst_addr = chan->dma_config.dst_addr; + /* Set device data size */ dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width); if (dst_bus_width < 0) @@ -567,7 +579,7 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst))); /* Set memory data size */ - src_addr_width = stm32_mdma_get_max_width(buf_len, tlen); + src_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen); chan->mem_width = src_addr_width; src_bus_width = stm32_mdma_get_width(chan, src_addr_width); if (src_bus_width < 0) @@ -587,15 +599,19 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst))); /* Select bus */ - dst_addr = chan->dma_config.dst_addr; stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, dst_addr); + if (dst_bus_width != src_bus_width) + ctcr |= STM32_MDMA_CTCR_PKE; + /* Set destination address */ stm32_mdma_write(dmadev, STM32_MDMA_CDAR(chan->id), dst_addr); break; case DMA_DEV_TO_MEM: + src_addr = chan->dma_config.src_addr; + /* Set device data size */ src_bus_width = stm32_mdma_get_width(chan, src_addr_width); if (src_bus_width < 0) @@ -611,7 +627,7 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst))); /* Set memory data size */ - dst_addr_width = stm32_mdma_get_max_width(buf_len, tlen); + dst_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen); chan->mem_width = dst_addr_width; dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width); if (dst_bus_width < 0) @@ -630,10 +646,12 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst))); /* Select bus */ - src_addr = chan->dma_config.src_addr; stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, src_addr); + if (dst_bus_width != src_bus_width) + ctcr |= STM32_MDMA_CTCR_PKE; + /* Set source address */ stm32_mdma_write(dmadev, STM32_MDMA_CSAR(chan->id), src_addr); break; @@ -719,23 +737,27 @@ static int stm32_mdma_setup_xfer(struct stm32_mdma_chan *chan, return -EINVAL; } - ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, - &ctbr, sg_dma_len(sg)); - if (ret < 0) - return ret; - if (direction == DMA_MEM_TO_DEV) { src_addr = sg_dma_address(sg); dst_addr = dma_config->dst_addr; + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, + &ctcr, &ctbr, src_addr, + sg_dma_len(sg)); stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, src_addr); } else { src_addr = dma_config->src_addr; dst_addr = sg_dma_address(sg); + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, + &ctcr, &ctbr, dst_addr, + sg_dma_len(sg)); stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, dst_addr); } + if (ret < 0) + return ret; + stm32_mdma_setup_hwdesc(chan, desc, direction, i, src_addr, dst_addr, sg_dma_len(sg), ctcr, ctbr, i == sg_len - 1, i == 0, false); @@ -830,27 +852,29 @@ stm32_mdma_prep_dma_cyclic(struct dma_chan *c, dma_addr_t buf_addr, if (!desc) return NULL; - ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, &ctbr, - period_len); - if (ret < 0) - goto xfer_setup_err; - - /* Enable interrupts */ - ccr &= ~STM32_MDMA_CCR_IRQ_MASK; - ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE | STM32_MDMA_CCR_BTIE; - desc->ccr = ccr; - /* Select bus */ if (direction == DMA_MEM_TO_DEV) { src_addr = buf_addr; + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, + &ctbr, src_addr, period_len); stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, src_addr); } else { dst_addr = buf_addr; + ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, + &ctbr, dst_addr, period_len); stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, dst_addr); } + if (ret < 0) + goto xfer_setup_err; + + /* Enable interrupts */ + ccr &= ~STM32_MDMA_CCR_IRQ_MASK; + ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE | STM32_MDMA_CCR_BTIE; + desc->ccr = ccr; + /* Configure hwdesc list */ for (i = 0; i < count; i++) { if (direction == DMA_MEM_TO_DEV) { @@ -956,9 +980,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1)); /* Set source best burst size */ - max_width = stm32_mdma_get_max_width(len, tlen); - if (src % max_width) - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + max_width = stm32_mdma_get_max_width(src, len, tlen); src_bus_width = stm32_mdma_get_width(chan, max_width); max_burst = tlen / max_width; @@ -971,9 +993,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, STM32_MDMA_CTCR_SINCOS(src_bus_width); /* Set destination best burst size */ - max_width = stm32_mdma_get_max_width(len, tlen); - if (dest % max_width) - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + max_width = stm32_mdma_get_max_width(dest, len, tlen); dst_bus_width = stm32_mdma_get_width(chan, max_width); max_burst = tlen / max_width; @@ -1014,9 +1034,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, STM32_MDMA_MAX_BLOCK_LEN); /* Set source best burst size */ - max_width = stm32_mdma_get_max_width(len, tlen); - if (src % max_width) - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + max_width = stm32_mdma_get_max_width(src, len, tlen); src_bus_width = stm32_mdma_get_width(chan, max_width); max_burst = tlen / max_width; @@ -1030,9 +1048,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, STM32_MDMA_CTCR_SINCOS(src_bus_width); /* Set destination best burst size */ - max_width = stm32_mdma_get_max_width(len, tlen); - if (dest % max_width) - max_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + max_width = stm32_mdma_get_max_width(dest, len, tlen); dst_bus_width = stm32_mdma_get_width(chan, max_width); max_burst = tlen / max_width;
If source and destination bus width differs pack/unpack MDMA feature has to be activated for alignment. This pack/unpack feature implies to have both source/destination address and buffer length aligned on bus width. Fixes: a4ffb13c8946 ("dmaengine: Add STM32 MDMA driver") Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> --- drivers/dma/stm32-mdma.c | 84 ++++++++++++++++++++++++++++-------------------- 1 file changed, 50 insertions(+), 34 deletions(-)