diff mbox

ARM64: dts: meson-gxbb-nanopi-k2: Add HDMI, CEC and CVBS nodes

Message ID 1529998855-8098-1-git-send-email-narmstrong@baylibre.com (mailing list archive)
State New, archived
Headers show

Commit Message

Neil Armstrong June 26, 2018, 7:40 a.m. UTC 
The Amlogic Meson GXBB based Nanopi-K2 board has an HDMI connector
with CEC and CVBS available on the 40pin header.
This patch adds the nodes to enable HDMI, CEC and CVBS functionnalities.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 .../boot/dts/amlogic/meson-gxbb-nanopi-k2.dts      | 48 ++++++++++++++++++++++
 1 file changed, 48 insertions(+)

Comments

Kevin Hilman June 29, 2018, 9:40 p.m. UTC | #1 
Neil Armstrong <narmstrong@baylibre.com> writes:

> The Amlogic Meson GXBB based Nanopi-K2 board has an HDMI connector
> with CEC and CVBS available on the 40pin header.
> This patch adds the nodes to enable HDMI, CEC and CVBS functionnalities.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Applied to v4.19/dt64,

Kevin
diff mbox

Patch

diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index 7d5709c..cbe99bd 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -106,6 +106,42 @@ 
 		compatible = "mmc-pwrseq-emmc";
 		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
 	};
+
+	/* CVBS is available on CON1 pin 36, disabled by default */
+	cvbs-connector {
+		compatible = "composite-video-connector";
+		status = "disabled";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
 };
 
 &ethmac {
@@ -137,6 +173,18 @@ 
 	};
 };
 
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
 &ir {
 	status = "okay";
 	pinctrl-0 = <&remote_input_ao_pins>;