diff mbox series

[V5,4/6] dts: imx: add common imx7ulp dtsi support

Message ID 1541862478-7839-5-git-send-email-aisheng.dong@nxp.com (mailing list archive)
State New, archived
Headers show
Series ARM: imx: add imx7ulp support | expand

Commit Message

Aisheng Dong Nov. 10, 2018, 3:13 p.m. UTC 
The i.MX 7ULP family of processors features NXP's advanced implementation
of the Arm Cortex-A7 core, the Arm Cortex-M4 core, as well as a 3D and 2D
Graphics Processing Units (GPUs).

This patch aims to add the initial support including:
1) CLK
2) GPIO PTC, PTD, PTE, PTF
3) uSDHC 1/2
4) LPUART 4/5/6/7
5) LPI2C 6/7

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
---
ChangeLog:
v4->v5:
 * add input clocks for PCC module
v3->v4:
 * no changes
v2->v3:
 * change to generic node names
 * remove arch timer due to:
   1) arch timer is fixed to 1Mhz which is lower accurate than TPM timer (3Mhz).
   2) no firmware progrem CNTFREQ
   3) cpuidle driver is still not in tree will may cause system hang
v1->v2:
 * update clk part due to binding change
 * separate soc.dtsi from board.dts
---
 arch/arm/boot/dts/imx7ulp.dtsi | 346 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 346 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx7ulp.dtsi

Comments

Fabio Estevam Nov. 10, 2018, 3:52 p.m. UTC | #1 
On Sat, Nov 10, 2018 at 1:13 PM A.s. Dong <aisheng.dong@nxp.com> wrote:
>
> The i.MX 7ULP family of processors features NXP's advanced implementation
> of the Arm Cortex-A7 core, the Arm Cortex-M4 core, as well as a 3D and 2D
> Graphics Processing Units (GPUs).
>
> This patch aims to add the initial support including:
> 1) CLK
> 2) GPIO PTC, PTD, PTE, PTF
> 3) uSDHC 1/2
> 4) LPUART 4/5/6/7
> 5) LPI2C 6/7
>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: devicetree@vger.kernel.org
> Cc: Sascha Hauer <kernel@pengutronix.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Shawn Guo Dec. 6, 2018, 2:51 p.m. UTC | #2 
On Sat, Nov 10, 2018 at 03:13:08PM +0000, A.s. Dong wrote:
> The i.MX 7ULP family of processors features NXP's advanced implementation
> of the Arm Cortex-A7 core, the Arm Cortex-M4 core, as well as a 3D and 2D
> Graphics Processing Units (GPUs).
> 
> This patch aims to add the initial support including:
> 1) CLK
> 2) GPIO PTC, PTD, PTE, PTF
> 3) uSDHC 1/2
> 4) LPUART 4/5/6/7
> 5) LPI2C 6/7
> 
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: devicetree@vger.kernel.org
> Cc: Sascha Hauer <kernel@pengutronix.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>

Changed the subject prefix like 'ARM: dts: imx: ...', and applied the
patch.

Shawn
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/imx7ulp.dtsi b/arch/arm/boot/dts/imx7ulp.dtsi
new file mode 100644
index 0000000..931b275
--- /dev/null
+++ b/arch/arm/boot/dts/imx7ulp.dtsi
@@ -0,0 +1,346 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017-2018 NXP
+ *   Dong Aisheng <aisheng.dong@nxp.com>
+ */
+
+#include <dt-bindings/clock/imx7ulp-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include "imx7ulp-pinfunc.h"
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		gpio0 = &gpio_ptc;
+		gpio1 = &gpio_ptd;
+		gpio2 = &gpio_pte;
+		gpio3 = &gpio_ptf;
+		i2c0 = &lpi2c6;
+		i2c1 = &lpi2c7;
+		mmc0 = &usdhc0;
+		mmc1 = &usdhc1;
+		serial0 = &lpuart4;
+		serial1 = &lpuart5;
+		serial2 = &lpuart6;
+		serial3 = &lpuart7;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	intc: interrupt-controller@40021000 {
+		compatible = "arm,cortex-a7-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x40021000 0x1000>,
+		      <0x40022000 0x1000>;
+	};
+
+	rosc: clock-rosc {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "rosc";
+		#clock-cells = <0>;
+	};
+
+	sosc: clock-sosc {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "sosc";
+		#clock-cells = <0>;
+	};
+
+	sirc: clock-sirc {
+		compatible = "fixed-clock";
+		clock-frequency = <16000000>;
+		clock-output-names = "sirc";
+		#clock-cells = <0>;
+	};
+
+	firc: clock-firc {
+		compatible = "fixed-clock";
+		clock-frequency = <48000000>;
+		clock-output-names = "firc";
+		#clock-cells = <0>;
+	};
+
+	upll: clock-upll {
+		compatible = "fixed-clock";
+		clock-frequency = <480000000>;
+		clock-output-names = "upll";
+		#clock-cells = <0>;
+	};
+
+	mpll: clock-mpll {
+		compatible = "fixed-clock";
+		clock-frequency = <480000000>;
+		clock-output-names = "mpll";
+		#clock-cells = <0>;
+	};
+
+	ahbbridge0: bus@40000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x40000000 0x800000>;
+		ranges;
+
+		lpuart4: serial@402d0000 {
+			compatible = "fsl,imx7ulp-lpuart";
+			reg = <0x402d0000 0x1000>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pcc2 IMX7ULP_CLK_LPUART4>;
+			clock-names = "ipg";
+			assigned-clocks = <&pcc2 IMX7ULP_CLK_LPUART4>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>;
+			assigned-clock-rates = <24000000>;
+			status = "disabled";
+		};
+
+		lpuart5: serial@402e0000 {
+			compatible = "fsl,imx7ulp-lpuart";
+			reg = <0x402e0000 0x1000>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pcc2 IMX7ULP_CLK_LPUART5>;
+			clock-names = "ipg";
+			assigned-clocks = <&pcc2 IMX7ULP_CLK_LPUART5>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
+			assigned-clock-rates = <48000000>;
+			status = "disabled";
+		};
+
+		tpm5: tpm@40260000 {
+			compatible = "fsl,imx7ulp-tpm";
+			reg = <0x40260000 0x1000>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>,
+				 <&pcc2 IMX7ULP_CLK_LPTPM5>;
+			clock-names = "ipg", "per";
+		};
+
+		usdhc0: mmc@40370000 {
+			compatible = "fsl,imx7ulp-usdhc", "fsl,imx6sx-usdhc";
+			reg = <0x40370000 0x10000>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>,
+				 <&scg1 IMX7ULP_CLK_NIC1_DIV>,
+				 <&pcc2 IMX7ULP_CLK_USDHC0>;
+			clock-names ="ipg", "ahb", "per";
+			assigned-clocks = <&pcc2 IMX7ULP_CLK_USDHC0>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_NIC1_DIV>;
+			bus-width = <4>;
+			fsl,tuning-start-tap = <20>;
+			fsl,tuning-step= <2>;
+			status = "disabled";
+		};
+
+		usdhc1: mmc@40380000 {
+			compatible = "fsl,imx7ulp-usdhc", "fsl,imx6sx-usdhc";
+			reg = <0x40380000 0x10000>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>,
+				 <&scg1 IMX7ULP_CLK_NIC1_DIV>,
+				 <&pcc2 IMX7ULP_CLK_USDHC1>;
+			clock-names ="ipg", "ahb", "per";
+			assigned-clocks = <&pcc2 IMX7ULP_CLK_USDHC1>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_NIC1_DIV>;
+			bus-width = <4>;
+			fsl,tuning-start-tap = <20>;
+			fsl,tuning-step= <2>;
+			status = "disabled";
+		};
+
+		scg1: clock-controller@403e0000 {
+			compatible = "fsl,imx7ulp-scg1";
+			reg = <0x403e0000 0x10000>;
+			clocks = <&rosc>, <&sosc>, <&sirc>,
+				 <&firc>, <&upll>, <&mpll>;
+			clock-names = "rosc", "sosc", "sirc",
+				      "firc", "upll", "mpll";
+			#clock-cells = <1>;
+		};
+
+		pcc2: clock-controller@403f0000 {
+			compatible = "fsl,imx7ulp-pcc2";
+			reg = <0x403f0000 0x10000>;
+			#clock-cells = <1>;
+			clocks = <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>,
+				 <&scg1 IMX7ULP_CLK_NIC1_DIV>,
+				 <&scg1 IMX7ULP_CLK_DDR_DIV>,
+				 <&scg1 IMX7ULP_CLK_APLL_PFD2>,
+				 <&scg1 IMX7ULP_CLK_APLL_PFD1>,
+				 <&scg1 IMX7ULP_CLK_APLL_PFD0>,
+				 <&scg1 IMX7ULP_CLK_UPLL>,
+				 <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>,
+				 <&scg1 IMX7ULP_CLK_MIPI_PLL>,
+				 <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>,
+				 <&scg1 IMX7ULP_CLK_ROSC>,
+				 <&scg1 IMX7ULP_CLK_SPLL_BUS_CLK>;
+			clock-names = "nic1_bus_clk", "nic1_clk", "ddr_clk",
+				      "apll_pfd2", "apll_pfd1", "apll_pfd0",
+				      "upll", "sosc_bus_clk", "mpll",
+				      "firc_bus_clk", "rosc", "spll_bus_clk";
+			assigned-clocks = <&pcc2 IMX7ULP_CLK_LPTPM5>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>;
+		};
+
+		smc1: smc1@40410000 {
+			compatible = "fsl,imx7ulp-smc1";
+			reg = <0x40410000 0x1000>;
+		};
+
+		pcc3: clock-controller@40b30000 {
+			compatible = "fsl,imx7ulp-pcc3";
+			reg = <0x40b30000 0x10000>;
+			#clock-cells = <1>;
+			clocks = <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>,
+				 <&scg1 IMX7ULP_CLK_NIC1_DIV>,
+				 <&scg1 IMX7ULP_CLK_DDR_DIV>,
+				 <&scg1 IMX7ULP_CLK_APLL_PFD2>,
+				 <&scg1 IMX7ULP_CLK_APLL_PFD1>,
+				 <&scg1 IMX7ULP_CLK_APLL_PFD0>,
+				 <&scg1 IMX7ULP_CLK_UPLL>,
+				 <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>,
+				 <&scg1 IMX7ULP_CLK_MIPI_PLL>,
+				 <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>,
+				 <&scg1 IMX7ULP_CLK_ROSC>,
+				 <&scg1 IMX7ULP_CLK_SPLL_BUS_CLK>;
+			clock-names = "nic1_bus_clk", "nic1_clk", "ddr_clk",
+				      "apll_pfd2", "apll_pfd1", "apll_pfd0",
+				      "upll", "sosc_bus_clk", "mpll",
+				      "firc_bus_clk", "rosc", "spll_bus_clk";
+		};
+	};
+
+	ahbbridge1: bus@40800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x40800000 0x800000>;
+		ranges;
+
+		lpi2c6: i2c@40a40000 {
+			compatible = "fsl,imx7ulp-lpi2c";
+			reg = <0x40a40000 0x10000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>;
+			clock-names = "ipg";
+			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
+			assigned-clock-rates = <48000000>;
+			status = "disabled";
+		};
+
+		lpi2c7: i2c@40a50000 {
+			compatible = "fsl,imx7ulp-lpi2c";
+			reg = <0x40a50000 0x10000>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>;
+			clock-names = "ipg";
+			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
+			assigned-clock-rates = <48000000>;
+			status = "disabled";
+		};
+
+		lpuart6: serial@40a60000 {
+			compatible = "fsl,imx7ulp-lpuart";
+			reg = <0x40a60000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pcc3 IMX7ULP_CLK_LPUART6>;
+			clock-names = "ipg";
+			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPUART6>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
+			assigned-clock-rates = <48000000>;
+			status = "disabled";
+		};
+
+		lpuart7: serial@40a70000 {
+			compatible = "fsl,imx7ulp-lpuart";
+			reg = <0x40a70000 0x1000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pcc3  IMX7ULP_CLK_LPUART7>;
+			clock-names = "ipg";
+			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPUART7>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
+			assigned-clock-rates = <48000000>;
+			status = "disabled";
+		};
+
+		iomuxc1: pinctrl@40ac0000 {
+			compatible = "fsl,imx7ulp-iomuxc1";
+			reg = <0x40ac0000 0x1000>;
+		};
+
+		gpio_ptc: gpio@40ae0000 {
+			compatible = "fsl,imx7ulp-gpio", "fsl,vf610-gpio";
+			reg = <0x40ae0000 0x1000 0x400f0000 0x40>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&pcc2 IMX7ULP_CLK_RGPIO2P1>,
+				 <&pcc3 IMX7ULP_CLK_PCTLC>;
+			clock-names = "gpio", "port";
+			gpio-ranges = <&iomuxc1 0 0 32>;
+		};
+
+		gpio_ptd: gpio@40af0000 {
+			compatible = "fsl,imx7ulp-gpio", "fsl,vf610-gpio";
+			reg = <0x40af0000 0x1000 0x400f0040 0x40>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&pcc2 IMX7ULP_CLK_RGPIO2P1>,
+				 <&pcc3 IMX7ULP_CLK_PCTLD>;
+			clock-names = "gpio", "port";
+			gpio-ranges = <&iomuxc1 0 32 32>;
+		};
+
+		gpio_pte: gpio@40b00000 {
+			compatible = "fsl,imx7ulp-gpio", "fsl,vf610-gpio";
+			reg = <0x40b00000 0x1000 0x400f0080 0x40>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&pcc2 IMX7ULP_CLK_RGPIO2P1>,
+				 <&pcc3 IMX7ULP_CLK_PCTLE>;
+			clock-names = "gpio", "port";
+			gpio-ranges = <&iomuxc1 0 64 32>;
+		};
+
+		gpio_ptf: gpio@40b10000 {
+			compatible = "fsl,imx7ulp-gpio", "fsl,vf610-gpio";
+			reg = <0x40b10000 0x1000 0x400f00c0 0x40>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&pcc2 IMX7ULP_CLK_RGPIO2P1>,
+				 <&pcc3 IMX7ULP_CLK_PCTLF>;
+			clock-names = "gpio", "port";
+			gpio-ranges = <&iomuxc1 0 96 32>;
+		};
+	};
+};