diff mbox series

[v2,06/15] arm64: dts: imx8: add adma lpcg clocks

Message ID 1563290089-11085-7-git-send-email-aisheng.dong@nxp.com (mailing list archive)
State New, archived
Headers show
Series arm64: dts: imx8: architecture improvement and adding imx8qm support | expand

Commit Message

Aisheng Dong July 16, 2019, 3:14 p.m. UTC 
Add adma lpcg clocks

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
---
ChangeLog:
v1->v2:
 * Use old SCU clock binding temporarily to avoid build warning due to SCU
   clock cell will be changed to 2.
 * add power domain property
---
 arch/arm64/boot/dts/freescale/imx8-ss-adma.dtsi | 98 +++++++++++++++++++++++++
 1 file changed, 98 insertions(+)

Comments

Fabio Estevam July 16, 2019, 7:28 p.m. UTC | #1 
On Tue, Jul 16, 2019 at 12:37 PM Dong Aisheng <aisheng.dong@nxp.com> wrote:

> +       uart0_lpcg: clock-controller@5a460000 {
> +               reg = <0x5a460000 0x10000>;
> +               #clock-cells = <1>;
> +               clocks = <&clk IMX_ADMA_UART0_CLK>,
> +                        <&dma_ipg_clk>;

Putting the clocks into a single line helps readability, even if it is
over 80 col.

> +               bit-offset = <0 16>;
> +               clock-output-names = "uart0_lpcg_baud_clk",
> +                                    "uart0_lpcg_ipg_clk";

Same here.
Dong Aisheng July 17, 2019, 8:22 a.m. UTC | #2 
On Wed, Jul 17, 2019 at 3:28 AM Fabio Estevam <festevam@gmail.com> wrote:
>
> On Tue, Jul 16, 2019 at 12:37 PM Dong Aisheng <aisheng.dong@nxp.com> wrote:
>
> > +       uart0_lpcg: clock-controller@5a460000 {
> > +               reg = <0x5a460000 0x10000>;
> > +               #clock-cells = <1>;
> > +               clocks = <&clk IMX_ADMA_UART0_CLK>,
> > +                        <&dma_ipg_clk>;
>
> Putting the clocks into a single line helps readability, even if it is
> over 80 col.
>

Is this a new rule? I'm not aware of this requirement.
By looking at imx8mq.dts, it seems also have not followed that rule.
I'm a bit concern that it might be super long for other lpcgs with 5 clocks.
e.g. enet.

Regards
Aisheng

> > +               bit-offset = <0 16>;
> > +               clock-output-names = "uart0_lpcg_baud_clk",
> > +                                    "uart0_lpcg_ipg_clk";
>
> Same here.
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-adma.dtsi
index 8738028..f0681a7 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-adma.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-adma.dtsi
@@ -4,12 +4,22 @@ 
  *	Dong Aisheng <aisheng.dong@nxp.com>
  */
 
+#include <dt-bindings/firmware/imx/rsrc.h>
+
 adma_subsys: bus@59000000 {
 	compatible = "simple-bus";
 	#address-cells = <1>;
 	#size-cells = <1>;
 	ranges = <0x59000000 0x0 0x59000000 0x2000000>;
 
+	dma_ipg_clk: clock-dma-ipg {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <120000000>;
+		clock-output-names = "dma_ipg_clk";
+	};
+
+	/* LPCG clocks */
 	adma_lpcg: clock-controller@59000000 {
 		reg = <0x59000000 0x2000000>;
 		#clock-cells = <1>;
@@ -55,6 +65,50 @@  adma_subsys: bus@59000000 {
 		status = "disabled";
 	};
 
+	uart0_lpcg: clock-controller@5a460000 {
+		reg = <0x5a460000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&clk IMX_ADMA_UART0_CLK>,
+			 <&dma_ipg_clk>;
+		bit-offset = <0 16>;
+		clock-output-names = "uart0_lpcg_baud_clk",
+				     "uart0_lpcg_ipg_clk";
+		power-domains = <&pd IMX_SC_R_UART_0>;
+	};
+
+	uart1_lpcg: clock-controller@5a470000 {
+		reg = <0x5a470000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&clk IMX_ADMA_UART1_CLK>,
+			 <&dma_ipg_clk>;
+		bit-offset = <0 16>;
+		clock-output-names = "uart1_lpcg_baud_clk",
+				     "uart1_lpcg_ipg_clk";
+		power-domains = <&pd IMX_SC_R_UART_1>;
+	};
+
+	uart2_lpcg: clock-controller@5a480000 {
+		reg = <0x5a480000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&clk IMX_ADMA_UART2_CLK>,
+			 <&dma_ipg_clk>;
+		bit-offset = <0 16>;
+		clock-output-names = "uart2_lpcg_baud_clk",
+				     "uart2_lpcg_ipg_clk";
+		power-domains = <&pd IMX_SC_R_UART_2>;
+	};
+
+	uart3_lpcg: clock-controller@5a490000 {
+		reg = <0x5a490000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&clk IMX_ADMA_UART3_CLK>,
+			 <&dma_ipg_clk>;
+		bit-offset = <0 16>;
+		clock-output-names = "uart3_lpcg_baud_clk",
+				     "uart3_lpcg_ipg_clk";
+		power-domains = <&pd IMX_SC_R_UART_3>;
+	};
+
 	adma_i2c0: i2c@5a800000 {
 		reg = <0x5a800000 0x4000>;
 		interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
@@ -102,4 +156,48 @@  adma_subsys: bus@59000000 {
 		power-domains = <&pd IMX_SC_R_I2C_3>;
 		status = "disabled";
 	};
+
+	i2c0_lpcg: clock-controller@5ac00000 {
+		reg = <0x5ac00000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&clk IMX_ADMA_I2C0_CLK>,
+			 <&dma_ipg_clk>;
+		bit-offset = <0 16>;
+		clock-output-names = "i2c0_lpcg_clk",
+				     "i2c0_lpcg_ipg_clk";
+		power-domains = <&pd IMX_SC_R_I2C_0>;
+	};
+
+	i2c1_lpcg: clock-controller@5ac10000 {
+		reg = <0x5ac10000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&clk IMX_ADMA_I2C1_CLK>,
+			 <&dma_ipg_clk>;
+		bit-offset = <0 16>;
+		clock-output-names = "i2c1_lpcg_clk",
+				     "i2c1_lpcg_ipg_clk";
+		power-domains = <&pd IMX_SC_R_I2C_1>;
+	};
+
+	i2c2_lpcg: clock-controller@5ac20000 {
+		reg = <0x5ac20000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&clk IMX_ADMA_I2C2_CLK>,
+			 <&dma_ipg_clk>;
+		bit-offset = <0 16>;
+		clock-output-names = "i2c2_lpcg_clk",
+				     "i2c2_lpcg_ipg_clk";
+		power-domains = <&pd IMX_SC_R_I2C_2>;
+	};
+
+	i2c3_lpcg: clock-controller@5ac30000 {
+		reg = <0x5ac30000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&clk IMX_ADMA_I2C3_CLK>,
+			 <&dma_ipg_clk>;
+		bit-offset = <0 16>;
+		clock-output-names = "i2c3_lpcg_clk",
+				     "i2c3_lpcg_ipg_clk";
+		power-domains = <&pd IMX_SC_R_I2C_3>;
+	};
 };