new file mode 100644
@@ -0,0 +1,105 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 NXP
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/fsl,imx8mp-dwc3.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP iMX8MP Soc USB Controller
+
+maintainers:
+ - Li Jun <jun.li@nxp.com>
+
+properties:
+ compatible:
+ const: fsl,imx8mp-dwc3
+
+ reg:
+ maxItems: 1
+ description: Address and length of the register set for the wrapper of
+ dwc3 core on the SOC.
+
+ "#address-cells":
+ enum: [ 1, 2 ]
+
+ "#size-cells":
+ enum: [ 1, 2 ]
+
+ dma-ranges:
+ description:
+ See section 2.3.9 of the DeviceTree Specification.
+
+ ranges: true
+
+ interrupts:
+ maxItems: 1
+ description: The interrupt that is asserted when a wakeup event is
+ received.
+
+ clocks:
+ description:
+ A list of phandle and clock-specifier pairs for the clocks
+ listed in clock-names.
+ items:
+ - description: system hsio root clock.
+ - description: suspend clock, used for usb wakeup logic.
+
+ clock-names:
+ items:
+ - const: hsio
+ - const: suspend
+
+# Required child node:
+
+patternProperties:
+ "^dwc3@[0-9a-f]+$":
+ type: object
+ description:
+ A child node must exist to represent the core DWC3 IP block
+ The content of the node is defined in dwc3.txt.
+
+required:
+ - compatible
+ - reg
+ - "#address-cells"
+ - "#size-cells"
+ - dma-ranges
+ - ranges
+ - clocks
+ - clock-names
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx8mp-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ usb3_0: usb@32f10100 {
+ compatible = "fsl,imx8mp-dwc3";
+ reg = <0x32f10100 0x8>;
+ clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
+ <&clk IMX8MP_CLK_USB_ROOT>;
+ clock-names = "hsio", "suspend";
+ interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ dma-ranges = <0x40000000 0x40000000 0xc0000000>;
+ ranges;
+
+ dwc3@38100000 {
+ compatible = "snps,dwc3";
+ reg = <0x38100000 0x10000>;
+ clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+ <&clk IMX8MP_CLK_USB_CORE_REF>,
+ <&clk IMX8MP_CLK_USB_ROOT>;
+ clock-names = "bus_early", "ref", "suspend";
+ assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>;
+ assigned-clock-rates = <500000000>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb3_phy0>, <&usb3_phy0>;
+ phy-names = "usb2-phy", "usb3-phy";
+ snps,dis-u2-freeclk-exists-quirk;
+ };
+ };
NXP imx8mp integrates 2 dwc3 3.30b IP and add some wakeup logic to support low power mode, the glue layer is for this wakeup functionality, which has a separated interrupt, can support wakeup from U3 and connect events for host, and vbus wakeup for device. Signed-off-by: Li Jun <jun.li@nxp.com> --- .../devicetree/bindings/usb/fsl,imx8mp-dwc3.yaml | 105 +++++++++++++++++++++ 1 file changed, 105 insertions(+)