| Message ID | 1608762196-29871-2-git-send-email-tharvey@gateworks.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/2] dt-bindings: arm: fsl: Add binding for Gateworks boards with IMX8MM | expand |
On Wed, Dec 23, 2020 at 02:23:16PM -0800, Tim Harvey wrote: > The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development > kits comprised of a GW700x SoM and a Baseboard. > > The GW700x SoM contains: > - IMX8MM SoC It's i.MX 8M Mini. https://www.nxp.com/products/processors-and-microcontrollers/arm-processors/i-mx-applications-processors/i-mx-8-processors/i-mx-8m-mini-arm-cortex-a53-cortex-m4-audio-voice-video:i.MX8MMINI > - LPDDR4 DRAM > - eMMC FLASH > - Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor) > - GbE PHY connected to the IMX8MM FEC > - Power Management IC > > The GW71xx Baseboard contains: > - 1x MiniPCIe Socket with USB2.0, PCIe, and SIM > - 1x RJ45 GbE (IMX8MM FEC) > - PCIe Clock generator > - GPS and accelerometer > - 1x USB 2.0 Front Panel connector > - wide range power supply > > The GW72xx Baseboard contains: > - 2x MiniPCIe Socket with USB2.0, PCIe, and SIM > - 2x RJ45 GbE (IMX8MM FEC and LAN743x) > - 1x MicroSD connector > - 1x USB 2.0 Front Panel connector > - 1x SPI connector > - PCIe Clock generator > - GPS and accelerometer > - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) > - wide range power supply > > The GW73xx Baseboard contains: > - 3x MiniPCIe Socket with USB2.0, PCIe, and SIM > - 2x RJ45 GbE (IMX8MM FEC and LAN743x) > - 1x MicroSD connector > - 1x USB 2.0 Front Panel connector > - 1x SPI connector > - WiFi/BT > - PCIe Clock generator > - GPS and accelerometer > - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) > - wide range power supply > > Signed-off-by: Tim Harvey <tharvey@gateworks.com> > --- > arch/arm64/boot/dts/freescale/Makefile | 3 + > .../boot/dts/freescale/imx8mm-venice-gw700x.dtsi | 482 +++++++++++++++++++++ > .../boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts | 19 + > .../boot/dts/freescale/imx8mm-venice-gw71xx.dtsi | 186 ++++++++ > .../boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts | 20 + > .../boot/dts/freescale/imx8mm-venice-gw72xx.dtsi | 311 +++++++++++++ > .../boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts | 19 + > .../boot/dts/freescale/imx8mm-venice-gw73xx.dtsi | 363 ++++++++++++++++ > 8 files changed, 1403 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi > > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile > index f8d5943..ecdd233 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -32,6 +32,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi > new file mode 100644 > index 00000000..7e1b96b > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi > @@ -0,0 +1,482 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/linux-event-codes.h> > +#include <dt-bindings/net/ti-dp83867.h> > + > +/ { > + memory@40000000 { > + device_type = "memory"; > + reg = <0x0 0x40000000 0 0x80000000>; > + }; > + > + gpio_keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + user_pb { > + label = "user_pb"; > + gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>; > + linux,code = <BTN_0>; > + }; > + > + user_pb1x { > + label = "user_pb1x"; > + linux,code = <BTN_1>; > + interrupt-parent = <&gsc>; > + interrupts = <0>; > + }; > + > + key_erased { > + label = "key-erased"; Above you use underscore, here hyphen. Make it consistent. > + linux,code = <BTN_2>; > + interrupt-parent = <&gsc>; > + interrupts = <1>; > + }; > + > + eeprom_wp { > + label = "eeprom_wp"; > + linux,code = <BTN_3>; > + interrupt-parent = <&gsc>; > + interrupts = <2>; > + }; > + > + tamper { > + label = "tamper"; > + linux,code = <BTN_4>; > + interrupt-parent = <&gsc>; > + interrupts = <5>; > + }; > + > + switch_hold { > + label = "switch_hold"; > + linux,code = <BTN_5>; > + interrupt-parent = <&gsc>; > + interrupts = <7>; > + }; > + }; > +}; > + > +&A53_0 { > + cpu-supply = <&buck3_reg>; > +}; > + > +&A53_1 { > + cpu-supply = <&buck3_reg>; > +}; > + > +&A53_2 { > + cpu-supply = <&buck3_reg>; > +}; > + > +&A53_3 { > + cpu-supply = <&buck3_reg>; > +}; > + > +&ddrc { > + operating-points-v2 = <&ddrc_opp_table>; > + > + ddrc_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + opp-25M { > + opp-hz = /bits/ 64 <25000000>; > + }; > + > + opp-100M { > + opp-hz = /bits/ 64 <100000000>; > + }; > + > + opp-750M { > + opp-hz = /bits/ 64 <750000000>; > + }; > + }; > +}; > + > +&fec1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_fec1>; > + phy-mode = "rgmii-id"; > + phy-handle = <ðphy0>; > + status = "okay"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy0: ethernet-phy@0 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <0>; > + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; > + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > + > + gsc: gsc@20 { Node name should describe class of a device so maybe "system-controller"? > + compatible = "gw,gsc"; > + reg = <0x20>; > + pinctrl-0 = <&pinctrl_gsc>; > + interrupt-parent = <&gpio2>; > + interrupts = <6 GPIO_ACTIVE_LOW>; Wrong flag. > + interrupt-controller; > + #interrupt-cells = <1>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + adc { Just to be sure - did you build it with W=1 to find any dtc warnings? > + compatible = "gw,gsc-adc"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + channel@6 { > + gw,mode = <0>; > + reg = <0x06>; > + label = "temp"; > + }; > + > + channel@8 { > + gw,mode = <1>; > + reg = <0x08>; > + label = "vdd_bat"; > + }; > + > + channel@16 { > + gw,mode = <4>; > + reg = <0x16>; > + label = "fan_tach"; > + }; > + > + channel@82 { > + gw,mode = <2>; > + reg = <0x82>; > + label = "vdd_vin"; > + gw,voltage-divider-ohms = <22100 1000>; > + }; > + > + channel@84 { > + gw,mode = <2>; > + reg = <0x84>; > + label = "vdd_adc1"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + > + channel@86 { > + gw,mode = <2>; > + reg = <0x86>; > + label = "vdd_adc2"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + > + channel@88 { > + gw,mode = <2>; > + reg = <0x88>; > + label = "vdd_dram"; > + }; > + > + channel@8c { > + gw,mode = <2>; > + reg = <0x8c>; > + label = "vdd_1p2"; > + }; > + > + channel@8e { > + gw,mode = <2>; > + reg = <0x8e>; > + label = "vdd_1p0"; > + }; > + > + channel@90 { > + gw,mode = <2>; > + reg = <0x90>; > + label = "vdd_2p5"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + > + channel@92 { > + gw,mode = <2>; > + reg = <0x92>; > + label = "vdd_3p3"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + > + channel@98 { > + gw,mode = <2>; > + reg = <0x98>; > + label = "vdd_0p95"; > + }; > + > + channel@9a { > + gw,mode = <2>; > + reg = <0x9a>; > + label = "vdd_1p8"; > + }; > + > + channel@a2 { > + gw,mode = <2>; > + reg = <0xa2>; > + label = "vdd_gsc"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + }; > + > + fan-controller@0 { > + #address-cells = <1>; > + #size-cells = <0>; These do not seem needed. > + compatible = "gw,gsc-fan"; > + reg = <0x0a>; > + }; > + }; > + > + gsc_gpio: pca9555@23 { Lookes like gpio-controller, so "gpio". Please run make dtbs_check to be sure your board validate against dt-schema. > + compatible = "nxp,pca9555"; > + reg = <0x23>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-parent = <&gsc>; > + interrupts = <4>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c02"; > + reg = <0x50>; > + pagesize = <16>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c02"; > + reg = <0x51>; > + pagesize = <16>; > + }; > + > + eeprom@52 { > + compatible = "atmel,24c32"; > + reg = <0x52>; > + pagesize = <32>; > + }; > + > + eeprom@53 { > + compatible = "atmel,24c32"; > + reg = <0x53>; > + pagesize = <32>; > + }; > + > + pmic@69 { > + compatible = "mps,mp5416"; > + reg = <0x69>; > + > + regulators { > + buck1 { > + regulator-name = "vdd_0p95"; > + regulator-min-microvolt = <805000>; > + regulator-max-microvolt = <1000000>; > + regulator-max-microamp = <2500000>; > + regulator-boot-on; > + }; > + > + buck2 { > + regulator-name = "vdd_soc"; > + regulator-min-microvolt = <805000>; > + regulator-max-microvolt = <900000>; > + regulator-max-microamp = <1000000>; > + regulator-boot-on; > + }; > + > + buck3_reg: buck3 { > + regulator-name = "vdd_arm"; > + regulator-min-microvolt = <805000>; > + regulator-max-microvolt = <1000000>; > + regulator-max-microamp = <2200000>; > + regulator-boot-on; > + }; > + > + buck4 { > + regulator-name = "vdd_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-max-microamp = <500000>; > + regulator-boot-on; > + }; > + > + ldo1 { > + regulator-name = "nvcc_snvs_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-max-microamp = <300000>; > + regulator-boot-on; > + }; > + > + ldo2 { > + regulator-name = "vdd_snvs_0p8"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <800000>; > + regulator-boot-on; > + }; > + > + ldo3 { > + regulator-name = "vdd_0p95"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <800000>; > + regulator-boot-on; > + }; > + > + ldo4 { > + regulator-name = "vdd_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + }; > + }; > + }; > +}; > + > +&i2c2 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + eeprom@52 { > + compatible = "atmel,24c32"; > + reg = <0x52>; > + pagesize = <32>; > + }; > +}; > + > +&uart2 { /* console */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + status = "okay"; > +}; > + > +&usdhc3 { /* eMMC */ > + assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>; > + assigned-clock-rates = <400000000>; > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc3>; > + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; > + bus-width = <8>; > + non-removable; > + status = "okay"; > +}; > + > +&wdog1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_wdog>; > + fsl,ext-reset-output; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl_fec1: fec1grp { > + fsl,pins = < > + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 > + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 > + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f > + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f > + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f > + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f > + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 > + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 > + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 > + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 > + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f > + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 > + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 > + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f > + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 > + >; > + }; > + > + pinctrl_gsc: gscirq { grp suffix. I think dtbs_check should point this out. > + fsl,pins = < > + MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6 0x159 > + >; > + }; > + > + pinctrl_i2c1: i2c1grp { > + fsl,pins = < > + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 > + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 > + >; > + }; > + > + pinctrl_i2c2: i2c2grp { > + fsl,pins = < > + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 > + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 > + >; > + }; > + > + pinctrl_uart2: uart2grp { > + fsl,pins = < > + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 > + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 > + >; > + }; > + > + pinctrl_usdhc3: usdhc3grp { > + fsl,pins = < > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 > + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 > + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 > + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 > + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 > + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 > + >; > + }; > + > + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { Ditto > + fsl,pins = < > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 > + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 > + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 > + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 > + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 > + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 > + >; > + }; > + > + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { Ditto > + fsl,pins = < > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 > + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 > + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 > + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 > + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 > + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 > + >; > + }; > + > + pinctrl_wdog: wdoggrp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 > + >; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > new file mode 100644 > index 00000000..3f88c4a > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > @@ -0,0 +1,19 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +/dts-v1/; > + > +#include "imx8mm.dtsi" > +#include "imx8mm-venice-gw700x.dtsi" > +#include "imx8mm-venice-gw71xx.dtsi" > + > +/ { > + model = "Gateworks Venice GW71xx-0x i.MX8MM Development Kit"; > + compatible = "gw,imx8mm-gw71xx-0x", "fsl,imx8mm"; > + > + chosen { > + stdout-path = &uart2; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > new file mode 100644 > index 00000000..a4eeb0d > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi This file is included only once, so it should be directly inside imx8mm-venice-gw71xx-0x.dts. Do not create empty DTS just to include DTSI and nothing more. It's really over-complicating simple hierarchy. > @@ -0,0 +1,186 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +/ { > + aliases { > + usb0 = &usbotg1; > + usb1 = &usbotg2; > + }; > + > + leds { led-controller > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpio_leds>; > + > + user1 { /* GRN */ led-0 > + label = "user1"; label is now deprecated. See the common bindings. > + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; > + default-state = "on"; > + linux,default-trigger = "heartbeat"; > + }; > + > + user2 { /* RED */ led-1 > + label = "user2"; > + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + }; > + > + pps { > + compatible = "pps-gpio"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pps>; > + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; > + status = "okay"; > + }; > + > + reg_usb_otg1_vbus: regulator-usb-otg1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_reg_usb1_en>; > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg1_vbus"; > + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + }; > +}; > + > +&ecspi2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi2>; > + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>; > + status = "okay"; > +}; > + > +&i2c2 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + accel@19 { accelerometer > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_accel>; > + compatible = "st,lis2de12"; > + reg = <0x19>; > + st,drdy-int-pin = <1>; > + interrupt-parent = <&gpio4>; > + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; > + interrupt-names = "INT1"; > + }; > +}; > + > +&i2c3 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + status = "okay"; > +}; > + > +&sai3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sai3>; > + assigned-clocks = <&clk IMX8MM_CLK_SAI3>; > + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; > + assigned-clock-rates = <24576000>; > + status = "okay"; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + status = "okay"; > +}; > + > +&usbotg1 { > + dr_mode = "otg"; > + vbus-supply = <®_usb_otg1_vbus>; > + status = "okay"; > +}; > + > +&usbotg2 { > + dr_mode = "host"; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + pinctrl_hog: hoggrp { > + fsl,pins = < > + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */ > + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */ > + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */ > + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */ > + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */ > + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x40000041 /* DIO2 */ > + MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x40000041 /* DIO2 */ > + >; > + }; > + > + pinctrl_accel: accelirq { Same comments as before. > + fsl,pins = < > + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 > + >; > + }; > + > + pinctrl_gpio_leds: gpioledgrp { > + fsl,pins = < > + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 > + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 > + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 > + >; > + }; > + > + pinctrl_pps: ppsgrp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 > + >; > + }; > + > + pinctrl_reg_usb1_en: regusb1grp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 > + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 > + >; > + }; > + > + pinctrl_spi2: spi2grp { > + fsl,pins = < > + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 > + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 > + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 > + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 > + >; > + }; > + > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 > + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 > + >; > + }; > + > + pinctrl_uart3: uart3grp { > + fsl,pins = < > + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 > + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 > + >; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts > new file mode 100644 > index 00000000..b1e7540 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts > @@ -0,0 +1,20 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +/dts-v1/; > + > +#include "imx8mm.dtsi" > +#include "imx8mm-venice-gw700x.dtsi" > +#include "imx8mm-venice-gw72xx.dtsi" The same - empty DTS just to include DTSI. Don't multiply files. This is development kit, carrier board, so entire contents of imx8mm-venice-gw72xx.dtsi is *here*. > + > +/ { > + model = "Gateworks Venice GW72xx-0x i.MX8MM Development Kit"; > + compatible = "gw,imx8mm-gw72xx-0x", "fsl,imx8mm"; > + > + chosen { > + stdout-path = &uart2; > + }; > +}; > + > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi > new file mode 100644 > index 00000000..3fb0213 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi > @@ -0,0 +1,311 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +/ { > + aliases { > + usb0 = &usbotg1; > + usb1 = &usbotg2; > + }; > + > + leds { It seems my comments apply to all your files, so I will finish the review here. Best regards, Krzysztof > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpio_leds>; > + > + user1 { /* GRN */ > + label = "user1"; > + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; > + default-state = "on"; > + linux,default-trigger = "heartbeat"; > + }; > + > + user2 { /* RED */ > + label = "user2"; > + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + };
On Wed, Dec 23, 2020 at 02:23:16PM -0800, Tim Harvey wrote: > The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development > kits comprised of a GW700x SoM and a Baseboard. > > The GW700x SoM contains: > - IMX8MM SoC > - LPDDR4 DRAM > - eMMC FLASH > - Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor) > - GbE PHY connected to the IMX8MM FEC > - Power Management IC > > The GW71xx Baseboard contains: > - 1x MiniPCIe Socket with USB2.0, PCIe, and SIM > - 1x RJ45 GbE (IMX8MM FEC) > - PCIe Clock generator > - GPS and accelerometer > - 1x USB 2.0 Front Panel connector > - wide range power supply > > The GW72xx Baseboard contains: > - 2x MiniPCIe Socket with USB2.0, PCIe, and SIM > - 2x RJ45 GbE (IMX8MM FEC and LAN743x) > - 1x MicroSD connector > - 1x USB 2.0 Front Panel connector > - 1x SPI connector > - PCIe Clock generator > - GPS and accelerometer > - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) > - wide range power supply > > The GW73xx Baseboard contains: > - 3x MiniPCIe Socket with USB2.0, PCIe, and SIM > - 2x RJ45 GbE (IMX8MM FEC and LAN743x) > - 1x MicroSD connector > - 1x USB 2.0 Front Panel connector > - 1x SPI connector > - WiFi/BT > - PCIe Clock generator > - GPS and accelerometer > - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) > - wide range power supply > > Signed-off-by: Tim Harvey <tharvey@gateworks.com> > --- > arch/arm64/boot/dts/freescale/Makefile | 3 + > .../boot/dts/freescale/imx8mm-venice-gw700x.dtsi | 482 +++++++++++++++++++++ > .../boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts | 19 + > .../boot/dts/freescale/imx8mm-venice-gw71xx.dtsi | 186 ++++++++ > .../boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts | 20 + > .../boot/dts/freescale/imx8mm-venice-gw72xx.dtsi | 311 +++++++++++++ > .../boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts | 19 + > .../boot/dts/freescale/imx8mm-venice-gw73xx.dtsi | 363 ++++++++++++++++ > 8 files changed, 1403 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi > > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile > index f8d5943..ecdd233 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -32,6 +32,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb (...) I have few more thoughts below. > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > new file mode 100644 > index 00000000..a4eeb0d > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > @@ -0,0 +1,186 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +/ { > + aliases { > + usb0 = &usbotg1; > + usb1 = &usbotg2; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpio_leds>; > + > + user1 { /* GRN */ > + label = "user1"; > + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; > + default-state = "on"; > + linux,default-trigger = "heartbeat"; > + }; > + > + user2 { /* RED */ > + label = "user2"; > + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + }; > + > + pps { > + compatible = "pps-gpio"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pps>; > + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; > + status = "okay"; > + }; > + > + reg_usb_otg1_vbus: regulator-usb-otg1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_reg_usb1_en>; > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg1_vbus"; > + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + }; > +}; > + > +&ecspi2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi2>; > + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>; > + status = "okay"; Why is it enabled? What's here? > +}; > + > +&i2c2 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + accel@19 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_accel>; > + compatible = "st,lis2de12"; > + reg = <0x19>; > + st,drdy-int-pin = <1>; > + interrupt-parent = <&gpio4>; > + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; > + interrupt-names = "INT1"; > + }; > +}; > + > +&i2c3 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + status = "okay"; Why is it enabled? What's here? > +}; > + > +&sai3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sai3>; > + assigned-clocks = <&clk IMX8MM_CLK_SAI3>; > + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; > + assigned-clock-rates = <24576000>; > + status = "okay"; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + status = "okay"; > +}; Why both UARTs are enabled on the Carrier? The console is UART2. Best regards, Krzysztof > + > +&usbotg1 { > + dr_mode = "otg"; > + vbus-supply = <®_usb_otg1_vbus>; > + status = "okay"; > +}; > + > +&usbotg2 { > + dr_mode = "host"; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + pinctrl_hog: hoggrp { > + fsl,pins = < > + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */ > + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */ > + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */ > + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */ > + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */ > + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x40000041 /* DIO2 */ > + MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x40000041 /* DIO2 */ > + >; > + }; > + > + pinctrl_accel: accelirq { > + fsl,pins = < > + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 > + >; > + }; > + > + pinctrl_gpio_leds: gpioledgrp { > + fsl,pins = < > + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 > + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 > + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 > + >; > + }; > + > + pinctrl_pps: ppsgrp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 > + >; > + }; > + > + pinctrl_reg_usb1_en: regusb1grp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 > + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 > + >; > + }; > + > + pinctrl_spi2: spi2grp { > + fsl,pins = < > + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 > + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 > + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 > + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 > + >; > + }; > + > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 > + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 > + >; > + }; > + > + pinctrl_uart3: uart3grp { > + fsl,pins = < > + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 > + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 > + >; > + }; > +};
On Thu, Dec 24, 2020 at 3:37 AM Krzysztof Kozlowski <krzk@kernel.org> wrote: > Thanks for the review! > On Wed, Dec 23, 2020 at 02:23:16PM -0800, Tim Harvey wrote: > > The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development > > kits comprised of a GW700x SoM and a Baseboard. > > > > The GW700x SoM contains: > > - IMX8MM SoC > > It's i.MX 8M Mini. > https://www.nxp.com/products/processors-and-microcontrollers/arm-processors/i-mx-applications-processors/i-mx-8-processors/i-mx-8m-mini-arm-cortex-a53-cortex-m4-audio-voice-video:i.MX8MMINI > ok > > - LPDDR4 DRAM > > - eMMC FLASH > > - Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor) > > - GbE PHY connected to the IMX8MM FEC > > - Power Management IC > > > > The GW71xx Baseboard contains: > > - 1x MiniPCIe Socket with USB2.0, PCIe, and SIM > > - 1x RJ45 GbE (IMX8MM FEC) > > - PCIe Clock generator > > - GPS and accelerometer > > - 1x USB 2.0 Front Panel connector > > - wide range power supply > > > > The GW72xx Baseboard contains: > > - 2x MiniPCIe Socket with USB2.0, PCIe, and SIM > > - 2x RJ45 GbE (IMX8MM FEC and LAN743x) > > - 1x MicroSD connector > > - 1x USB 2.0 Front Panel connector > > - 1x SPI connector > > - PCIe Clock generator > > - GPS and accelerometer > > - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) > > - wide range power supply > > > > The GW73xx Baseboard contains: > > - 3x MiniPCIe Socket with USB2.0, PCIe, and SIM > > - 2x RJ45 GbE (IMX8MM FEC and LAN743x) > > - 1x MicroSD connector > > - 1x USB 2.0 Front Panel connector > > - 1x SPI connector > > - WiFi/BT > > - PCIe Clock generator > > - GPS and accelerometer > > - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) > > - wide range power supply > > > > Signed-off-by: Tim Harvey <tharvey@gateworks.com> > > --- <snip> > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi > > @@ -0,0 +1,482 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +/* > > + * Copyright 2020 Gateworks Corporation > > + */ > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/input/linux-event-codes.h> > > +#include <dt-bindings/net/ti-dp83867.h> > > + > > +/ { > > + memory@40000000 { > > + device_type = "memory"; > > + reg = <0x0 0x40000000 0 0x80000000>; > > + }; > > + > > + gpio_keys { > > + compatible = "gpio-keys"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + user_pb { > > + label = "user_pb"; > > + gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>; > > + linux,code = <BTN_0>; > > + }; > > + > > + user_pb1x { > > + label = "user_pb1x"; > > + linux,code = <BTN_1>; > > + interrupt-parent = <&gsc>; > > + interrupts = <0>; > > + }; > > + > > + key_erased { > > + label = "key-erased"; > > Above you use underscore, here hyphen. Make it consistent. ok > > > + linux,code = <BTN_2>; > > + interrupt-parent = <&gsc>; > > + interrupts = <1>; > > + }; > > + > > + eeprom_wp { > > + label = "eeprom_wp"; > > + linux,code = <BTN_3>; > > + interrupt-parent = <&gsc>; > > + interrupts = <2>; > > + }; > > + > > + tamper { > > + label = "tamper"; > > + linux,code = <BTN_4>; > > + interrupt-parent = <&gsc>; > > + interrupts = <5>; > > + }; > > + > > + switch_hold { > > + label = "switch_hold"; > > + linux,code = <BTN_5>; > > + interrupt-parent = <&gsc>; > > + interrupts = <7>; > > + }; > > + }; > > +}; > > + <snip> > > + > > +&i2c1 { > > + clock-frequency = <100000>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_i2c1>; > > + status = "okay"; > > + > > + gsc: gsc@20 { > > Node name should describe class of a device so maybe > "system-controller"? > The node-name here must match 'gsc' due to the bindings. The name stands for 'Gateworks System Controller'. > > + compatible = "gw,gsc"; > > + reg = <0x20>; > > + pinctrl-0 = <&pinctrl_gsc>; > > + interrupt-parent = <&gpio2>; > > + interrupts = <6 GPIO_ACTIVE_LOW>; > > Wrong flag. > oops... thanks for catching it was supposed to be falling anyway. I will change to IRQ_TYPE_EDGE_FALLING > > + interrupt-controller; > > + #interrupt-cells = <1>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + adc { > > Just to be sure - did you build it with W=1 to find any dtc warnings? > I did 'make dtbs_check' but not with W=1... will do that for next submission > > + compatible = "gw,gsc-adc"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + <snip> > > + }; > > + > > + fan-controller@0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > These do not seem needed. They are required per Documentation/devicetree/bindings/mfd/gateworks-gsc.yaml but they should be inherited from the parent node right? So perhaps gateworks-gsc.yaml needs to remove them? > > > + compatible = "gw,gsc-fan"; > > + reg = <0x0a>; > > + }; > > + }; > > + > > + gsc_gpio: pca9555@23 { > > Lookes like gpio-controller, so "gpio". Please run make dtbs_check to be > sure your board validate against dt-schema. Yes, I see these warnings now with 'make dtbs_check W=1' Note when I do run 'make dtbs_check W=1' I see many warnings which seem invalid that I have to skip over: /usr/src/linux/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dt.yaml: pi nctrl@30330000: fec1grp:fsl,pins:0: [104, 720, 0, 0, 0, 3, 108, 724, 1216, 0, 1, 3, 112, 728, 0, 0, 0, 31, 116, 732, 0, 0, 0, 31, 120, 736, 0, 0, 0, 31, 124, 740, 0, 0, 0, 31, 156, 772, 0, 0, 0, 145, 152, 768, 0, 0, 0, 145, 148, 764, 0, 0, 0, 145, 144, 760, 0, 0, 0, 145, 132, 748, 0, 0, 0, 31, 140, 756, 0, 0, 0, 145, 136, 752, 0, 0, 0, 145, 128, 744, 0, 0, 0, 31, 244, 860, 0, 5, 0, 25] is too long From schema: /usr/src/linux/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml /usr/src/linux/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dt.yaml: pinctrl@30330000: fec1grp:fsl,pins:0: Additional items are not allowed (108, 724, 1216, 0, 1, 3, 112, 728, 0, 0, 0, 31, 116, 732, 0, 0, 0, 31, 120, 736, 0, 0, 0, 31, 124, 740, 0, 0, 0, 31, 156, 772, 0, 0, 0, 145, 152, 768, 0, 0, 0, 145, 148, 764, 0, 0, 0, 145, 144, 760, 0, 0, 0, 145, 132, 748, 0, 0, 0, 31, 140, 756, 0, 0, 0, 145, 136, 752, 0, 0, 0, 145, 128, 744, 0, 0, 0, 31, 244, 860, 0, 5, 0, 25 were unexpected) ^^^ It seems maybe something is too restrictive with Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml that doesn't allow an array of pins? I see lots of warnings about imx8mm gpmi as well but they don't have anything to do with my dtbs. > > > + compatible = "nxp,pca9555"; > > + reg = <0x23>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + interrupt-parent = <&gsc>; > > + interrupts = <4>; > > + }; > > + <snip> > > + > > +&iomuxc { > > + pinctrl_fec1: fec1grp { > > + fsl,pins = < > > + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 > > + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 > > + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f > > + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f > > + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f > > + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f > > + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 > > + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 > > + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 > > + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 > > + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f > > + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 > > + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 > > + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f > > + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 > > + >; > > + }; > > + > > + pinctrl_gsc: gscirq { > > grp suffix. I think dtbs_check should point this out. ok, I do see this warning with 'make dtbs_check W=1'. I will fix the node names for the iomux pin groups <snip> > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > > new file mode 100644 > > index 00000000..3f88c4a > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > > @@ -0,0 +1,19 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +/* > > + * Copyright 2020 Gateworks Corporation > > + */ > > + > > +/dts-v1/; > > + > > +#include "imx8mm.dtsi" > > +#include "imx8mm-venice-gw700x.dtsi" > > +#include "imx8mm-venice-gw71xx.dtsi" > > + > > +/ { > > + model = "Gateworks Venice GW71xx-0x i.MX8MM Development Kit"; > > + compatible = "gw,imx8mm-gw71xx-0x", "fsl,imx8mm"; > > + > > + chosen { > > + stdout-path = &uart2; > > + }; > > +}; > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > > new file mode 100644 > > index 00000000..a4eeb0d > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > > This file is included only once, so it should be directly inside imx8mm-venice-gw71xx-0x.dts. Do not create empty DTS just to include DTSI and nothing more. It's really over-complicating simple hierarchy. The reason for this is that the '0x' on the end is the SoM and in the future there will be a '1x', '2x' SoM so imagine: imx8mm-venice-gw71xx-2x.dts being the 'kit' that combines the imx8mm-venice-gw71xx.dtsi baseboard and imx8mm-venice-gw702x.dtsi SoM. Our numbering scheme has SoM's as gw70xx. I will add something to the commit log that explains this. > > > @@ -0,0 +1,186 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +/* > > + * Copyright 2020 Gateworks Corporation > > + */ > > + > > +/ { > > + aliases { > > + usb0 = &usbotg1; > > + usb1 = &usbotg2; > > + }; > > + > > + leds { > > led-controller ok - will fix > > > + compatible = "gpio-leds"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_gpio_leds>; > > + > > + user1 { /* GRN */ > > led-0 ok, will fix > > > + label = "user1"; > > label is now deprecated. See the common bindings. > ok, will fix by removing deprecated label and adding color/function props > > + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; > > + default-state = "on"; > > + linux,default-trigger = "heartbeat"; > > + }; > > + <snip> > > +&i2c2 { > > + clock-frequency = <400000>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_i2c2>; > > + status = "okay"; > > + > > + accel@19 { > > accelerometer > ok - will fix You also had asked why ecspi2, i2c3 were enabled (with no child nodes) and why uart1/uart3 were enabled on the carrier boards. The carrier boards have off-board connectors for ecspi2, i2c3 so I include them on the baseboard so that the Linux SPI/I2C userspace API's could be used. The carrier boards also have uart1 connected to a GPS, uart2/uart4 going to a multi-protocol RS232/RS485/RS422 transceiver that has some GPIO to configure it, and uart3 going to an offboard I/O connector. For this reason I have uart2 basic tx/rx configured on the gw70xx SoM and uart1/uart2-gpio/uart4 configures on the carrier board. I will submit a v2 shortly. Best regards, Tim
On Mon, Dec 28, 2020 at 11:02:40AM -0800, Tim Harvey wrote: > > + > > > +&i2c1 { > > > + clock-frequency = <100000>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_i2c1>; > > > + status = "okay"; > > > + > > > + gsc: gsc@20 { > > > > Node name should describe class of a device so maybe > > "system-controller"? > > > > The node-name here must match 'gsc' due to the bindings. The name > stands for 'Gateworks System Controller'. Indeed, so it must stay like this. > > + > > > + fan-controller@0 { > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > > These do not seem needed. > > They are required per > Documentation/devicetree/bindings/mfd/gateworks-gsc.yaml but they > should be inherited from the parent node right? So perhaps > gateworks-gsc.yaml needs to remove them? Maybe they shouldn't be in the bindings, either? These are only for nodes which have childre. The fan-controller does not have them. > > > > > > + compatible = "gw,gsc-fan"; > > > + reg = <0x0a>; > > > + }; > > > + }; > > > + > > > + gsc_gpio: pca9555@23 { > > > > Lookes like gpio-controller, so "gpio". Please run make dtbs_check to be > > sure your board validate against dt-schema. > > Yes, I see these warnings now with 'make dtbs_check W=1' dtbs_check without W=1. dtbs with W=1. These are different tools. > > Note when I do run 'make dtbs_check W=1' I see many warnings which > seem invalid that I have to skip over: > /usr/src/linux/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dt.yaml: pi > nctrl@30330000: fec1grp:fsl,pins:0: [104, 720, 0, 0, 0, 3, 108, 724, 1216, 0, 1, > 3, 112, 728, 0, 0, 0, 31, 116, 732, 0, 0, 0, 31, 120, 736, 0, 0, 0, > 31, 124, 740, 0, 0, 0, 31, 156, 772, 0, 0, 0, 145, 152, 768, 0, 0, 0, > 145, 148, 764, 0, 0, 0, 145, 144, 760, 0, 0, 0, 145, 132, 748, 0, 0, > 0, 31, 140, 756, 0, 0, 0, 145, 136, 752, 0, 0, 0, 145, 128, 744, 0, 0, > 0, 31, 244, 860, 0, 5, 0, 25] is too long > From schema: > /usr/src/linux/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml > /usr/src/linux/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dt.yaml: > pinctrl@30330000: fec1grp:fsl,pins:0: Additional items are not allowed > (108, 724, 1216, 0, 1, 3, 112, 728, 0, 0, 0, 31, 116, 732, 0, 0, 0, > 31, 120, 736, 0, 0, 0, 31, 124, 740, 0, 0, 0, 31, 156, 772, 0, 0, 0, > 145, 152, 768, 0, 0, 0, 145, 148, 764, 0, 0, 0, 145, 144, 760, 0, 0, > 0, 145, 132, 748, 0, 0, 0, 31, 140, 756, 0, 0, 0, 145, 136, 752, 0, 0, > 0, 145, 128, 744, 0, 0, 0, 31, 244, 860, 0, 5, 0, 25 were unexpected) > ^^^ It seems maybe something is too restrictive with > Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml that > doesn't allow an array of pins? This is expected because dt-schema does not accept pin groups in one array (<..., ....>). Compare your warnings with some other recent imx8mm designs. If you introduce new, these have to be fixed. > > I see lots of warnings about imx8mm gpmi as well but they don't have > anything to do with my dtbs. > > > > > > + compatible = "nxp,pca9555"; > > > + reg = <0x23>; > > > + gpio-controller; > > > + #gpio-cells = <2>; > > > + interrupt-parent = <&gsc>; > > > + interrupts = <4>; > > > + }; > > > + > <snip> > > > + > > > +&iomuxc { > > > + pinctrl_fec1: fec1grp { > > > + fsl,pins = < > > > + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 > > > + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 > > > + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f > > > + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f > > > + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f > > > + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f > > > + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 > > > + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 > > > + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 > > > + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 > > > + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f > > > + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 > > > + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 > > > + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f > > > + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 > > > + >; > > > + }; > > > + > > > + pinctrl_gsc: gscirq { > > > > grp suffix. I think dtbs_check should point this out. > > ok, I do see this warning with 'make dtbs_check W=1'. I will fix the > node names for the iomux pin groups > > <snip> > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > > > new file mode 100644 > > > index 00000000..3f88c4a > > > --- /dev/null > > > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > > > @@ -0,0 +1,19 @@ > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > > +/* > > > + * Copyright 2020 Gateworks Corporation > > > + */ > > > + > > > +/dts-v1/; > > > + > > > +#include "imx8mm.dtsi" > > > +#include "imx8mm-venice-gw700x.dtsi" > > > +#include "imx8mm-venice-gw71xx.dtsi" > > > + > > > +/ { > > > + model = "Gateworks Venice GW71xx-0x i.MX8MM Development Kit"; > > > + compatible = "gw,imx8mm-gw71xx-0x", "fsl,imx8mm"; > > > + > > > + chosen { > > > + stdout-path = &uart2; > > > + }; > > > +}; > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > > > new file mode 100644 > > > index 00000000..a4eeb0d > > > --- /dev/null > > > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > > > > This file is included only once, so it should be directly inside imx8mm-venice-gw71xx-0x.dts. Do not create empty DTS just to include DTSI and nothing more. It's really over-complicating simple hierarchy. > > The reason for this is that the '0x' on the end is the SoM and in the > future there will be a '1x', '2x' SoM so imagine: > imx8mm-venice-gw71xx-2x.dts being the 'kit' that combines the > imx8mm-venice-gw71xx.dtsi baseboard and imx8mm-venice-gw702x.dtsi SoM. > Our numbering scheme has SoM's as gw70xx. I will add something to the > commit log that explains this. If you really intend to upstream these future designs, then it's fine. Have in mind that if you do not upstream them, anyone can simplify later the hierarchy by renaming imx8mm-venice-gw71xx.dtsi into imx8mm-venice-gw71xx.dts. > > > > > > @@ -0,0 +1,186 @@ > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > > +/* > > > + * Copyright 2020 Gateworks Corporation > > > + */ > > > + > > > +/ { > > > + aliases { > > > + usb0 = &usbotg1; > > > + usb1 = &usbotg2; > > > + }; > > > + > > > + leds { > > > > led-controller > > ok - will fix > > > > > > + compatible = "gpio-leds"; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_gpio_leds>; > > > + > > > + user1 { /* GRN */ > > > > led-0 > > ok, will fix > > > > > > + label = "user1"; > > > > label is now deprecated. See the common bindings. > > > > ok, will fix by removing deprecated label and adding color/function props > > > > + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; > > > + default-state = "on"; > > > + linux,default-trigger = "heartbeat"; > > > + }; > > > + > <snip> > > > +&i2c2 { > > > + clock-frequency = <400000>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&pinctrl_i2c2>; > > > + status = "okay"; > > > + > > > + accel@19 { > > > > accelerometer > > > > ok - will fix > > You also had asked why ecspi2, i2c3 were enabled (with no child nodes) > and why uart1/uart3 were enabled on the carrier boards. > > The carrier boards have off-board connectors for ecspi2, i2c3 so I > include them on the baseboard so that the Linux SPI/I2C userspace > API's could be used. Sure, this makes sense. Can you add a comment to such nodes like: "UART on header" Customers usually copy the reference designs (boards) so it is usually useful to explain why something on carrier board was enabled, even though nothing is attached. Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index f8d5943..ecdd233 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -32,6 +32,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi new file mode 100644 index 00000000..7e1b96b --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi @@ -0,0 +1,482 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/net/ti-dp83867.h> + +/ { + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0x80000000>; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + user_pb { + label = "user_pb"; + gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>; + linux,code = <BTN_0>; + }; + + user_pb1x { + label = "user_pb1x"; + linux,code = <BTN_1>; + interrupt-parent = <&gsc>; + interrupts = <0>; + }; + + key_erased { + label = "key-erased"; + linux,code = <BTN_2>; + interrupt-parent = <&gsc>; + interrupts = <1>; + }; + + eeprom_wp { + label = "eeprom_wp"; + linux,code = <BTN_3>; + interrupt-parent = <&gsc>; + interrupts = <2>; + }; + + tamper { + label = "tamper"; + linux,code = <BTN_4>; + interrupt-parent = <&gsc>; + interrupts = <5>; + }; + + switch_hold { + label = "switch_hold"; + linux,code = <BTN_5>; + interrupt-parent = <&gsc>; + interrupts = <7>; + }; + }; +}; + +&A53_0 { + cpu-supply = <&buck3_reg>; +}; + +&A53_1 { + cpu-supply = <&buck3_reg>; +}; + +&A53_2 { + cpu-supply = <&buck3_reg>; +}; + +&A53_3 { + cpu-supply = <&buck3_reg>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-750M { + opp-hz = /bits/ 64 <750000000>; + }; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + gsc: gsc@20 { + compatible = "gw,gsc"; + reg = <0x20>; + pinctrl-0 = <&pinctrl_gsc>; + interrupt-parent = <&gpio2>; + interrupts = <6 GPIO_ACTIVE_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + adc { + compatible = "gw,gsc-adc"; + #address-cells = <1>; + #size-cells = <0>; + + channel@6 { + gw,mode = <0>; + reg = <0x06>; + label = "temp"; + }; + + channel@8 { + gw,mode = <1>; + reg = <0x08>; + label = "vdd_bat"; + }; + + channel@16 { + gw,mode = <4>; + reg = <0x16>; + label = "fan_tach"; + }; + + channel@82 { + gw,mode = <2>; + reg = <0x82>; + label = "vdd_vin"; + gw,voltage-divider-ohms = <22100 1000>; + }; + + channel@84 { + gw,mode = <2>; + reg = <0x84>; + label = "vdd_adc1"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@86 { + gw,mode = <2>; + reg = <0x86>; + label = "vdd_adc2"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@88 { + gw,mode = <2>; + reg = <0x88>; + label = "vdd_dram"; + }; + + channel@8c { + gw,mode = <2>; + reg = <0x8c>; + label = "vdd_1p2"; + }; + + channel@8e { + gw,mode = <2>; + reg = <0x8e>; + label = "vdd_1p0"; + }; + + channel@90 { + gw,mode = <2>; + reg = <0x90>; + label = "vdd_2p5"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@92 { + gw,mode = <2>; + reg = <0x92>; + label = "vdd_3p3"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@98 { + gw,mode = <2>; + reg = <0x98>; + label = "vdd_0p95"; + }; + + channel@9a { + gw,mode = <2>; + reg = <0x9a>; + label = "vdd_1p8"; + }; + + channel@a2 { + gw,mode = <2>; + reg = <0xa2>; + label = "vdd_gsc"; + gw,voltage-divider-ohms = <10000 10000>; + }; + }; + + fan-controller@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "gw,gsc-fan"; + reg = <0x0a>; + }; + }; + + gsc_gpio: pca9555@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gsc>; + interrupts = <4>; + }; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + pagesize = <32>; + }; + + eeprom@53 { + compatible = "atmel,24c32"; + reg = <0x53>; + pagesize = <32>; + }; + + pmic@69 { + compatible = "mps,mp5416"; + reg = <0x69>; + + regulators { + buck1 { + regulator-name = "vdd_0p95"; + regulator-min-microvolt = <805000>; + regulator-max-microvolt = <1000000>; + regulator-max-microamp = <2500000>; + regulator-boot-on; + }; + + buck2 { + regulator-name = "vdd_soc"; + regulator-min-microvolt = <805000>; + regulator-max-microvolt = <900000>; + regulator-max-microamp = <1000000>; + regulator-boot-on; + }; + + buck3_reg: buck3 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <805000>; + regulator-max-microvolt = <1000000>; + regulator-max-microamp = <2200000>; + regulator-boot-on; + }; + + buck4 { + regulator-name = "vdd_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-max-microamp = <500000>; + regulator-boot-on; + }; + + ldo1 { + regulator-name = "nvcc_snvs_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-max-microamp = <300000>; + regulator-boot-on; + }; + + ldo2 { + regulator-name = "vdd_snvs_0p8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-boot-on; + }; + + ldo3 { + regulator-name = "vdd_0p95"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-boot-on; + }; + + ldo4 { + regulator-name = "vdd_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + pagesize = <32>; + }; +}; + +&uart2 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usdhc3 { /* eMMC */ + assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 + >; + }; + + pinctrl_gsc: gscirq { + fsl,pins = < + MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6 0x159 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts new file mode 100644 index 00000000..3f88c4a --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +/dts-v1/; + +#include "imx8mm.dtsi" +#include "imx8mm-venice-gw700x.dtsi" +#include "imx8mm-venice-gw71xx.dtsi" + +/ { + model = "Gateworks Venice GW71xx-0x i.MX8MM Development Kit"; + compatible = "gw,imx8mm-gw71xx-0x", "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi new file mode 100644 index 00000000..a4eeb0d --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi @@ -0,0 +1,186 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +/ { + aliases { + usb0 = &usbotg1; + usb1 = &usbotg2; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + user1 { /* GRN */ + label = "user1"; + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + user2 { /* RED */ + label = "user2"; + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + pps { + compatible = "pps-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pps>; + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb1_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + accel@19 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_accel>; + compatible = "st,lis2de12"; + reg = <0x19>; + st,drdy-int-pin = <1>; + interrupt-parent = <&gpio4>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "INT1"; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MM_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */ + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */ + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */ + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */ + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */ + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x40000041 /* DIO2 */ + MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x40000041 /* DIO2 */ + >; + }; + + pinctrl_accel: accelirq { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 + >; + }; + + pinctrl_gpio_leds: gpioledgrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_pps: ppsgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 + >; + }; + + pinctrl_reg_usb1_en: regusb1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 + >; + }; + + pinctrl_spi2: spi2grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts new file mode 100644 index 00000000..b1e7540 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +/dts-v1/; + +#include "imx8mm.dtsi" +#include "imx8mm-venice-gw700x.dtsi" +#include "imx8mm-venice-gw72xx.dtsi" + +/ { + model = "Gateworks Venice GW72xx-0x i.MX8MM Development Kit"; + compatible = "gw,imx8mm-gw72xx-0x", "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; +}; + diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi new file mode 100644 index 00000000..3fb0213 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi @@ -0,0 +1,311 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +/ { + aliases { + usb0 = &usbotg1; + usb1 = &usbotg2; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + user1 { /* GRN */ + label = "user1"; + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + user2 { /* RED */ + label = "user2"; + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + pps { + compatible = "pps-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pps>; + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb1_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usb_otg2_vbus: regulator-usb-otg2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb2_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg2_vbus"; + gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + accel@19 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_accel>; + compatible = "st,lis2de12"; + reg = <0x19>; + st,drdy-int-pin = <1>; + interrupt-parent = <&gpio4>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "INT1"; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MM_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>,<&pinctrl_uart2_gpio>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + vbus-supply = <®_usb_otg2_vbus>; + status = "okay"; +}; + +&usdhc2 { /* microSD */ + assigned-clocks = <&clk IMX8MM_CLK_USDHC2>; + assigned-clock-rates = <200000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */ + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */ + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */ + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */ + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */ + >; + }; + + pinctrl_accel: accelirq { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 + >; + }; + + pinctrl_gpio_leds: gpioledgrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_pps: ppsgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 + >; + }; + + pinctrl_reg_usb1_en: regusb1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 + >; + }; + + pinctrl_reg_usb2_en: regusb2grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x41 + >; + }; + + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 + MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6 + >; + }; + + pinctrl_spi2: spi2grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + >; + }; + + pinctrl_uart2_gpio: uart2grpgpio { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x40000104 /*TERM*/ + MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x40000104 /*RS485*/ + MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2 0x40000104 /*HALF*/ + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4 + MX8MM_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0x1d0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts new file mode 100644 index 00000000..6905437 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +/dts-v1/; + +#include "imx8mm.dtsi" +#include "imx8mm-venice-gw700x.dtsi" +#include "imx8mm-venice-gw73xx.dtsi" + +/ { + model = "Gateworks Venice GW73xx-0x i.MX8MM Development Kit"; + compatible = "gw,imx8mm-gw73xx-0x", "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi new file mode 100644 index 00000000..8096e4b --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi @@ -0,0 +1,363 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +/ { + aliases { + usb0 = &usbotg1; + usb1 = &usbotg2; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + user1 { /* GRN */ + label = "user1"; + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + user2 { /* RED */ + label = "user2"; + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + pps { + compatible = "pps-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pps>; + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb1_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usb_otg2_vbus: regulator-usb-otg2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb2_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg2_vbus"; + gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_wifi_en: regulator-wifi-en { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_wl>; + compatible = "regulator-fixed"; + regulator-name = "wl"; + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; + startup-delay-us = <100>; + enable-active-high; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + accel@19 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_accel>; + compatible = "st,lis2de12"; + reg = <0x19>; + st,drdy-int-pin = <1>; + interrupt-parent = <&gpio4>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "INT1"; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MM_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>,<&pinctrl_uart2_gpio>; +}; + +&uart3 { /* bluetooth HCI */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>,<&pinctrl_bten>; + cts-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + shutdown-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + vbus-supply = <®_usb_otg2_vbus>; + status = "okay"; +}; + +&usdhc1 { /* SDIO WiFi */ + assigned-clocks = <&clk IMX8MM_CLK_USDHC1>; + assigned-clock-rates = <50000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <4>; + non-removable; + vmmc-supply = <®_wifi_en>; + status = "okay"; +}; + +&usdhc2 { /* microSD */ + assigned-clocks = <&clk IMX8MM_CLK_USDHC2>; + assigned-clock-rates = <200000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */ + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */ + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */ + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */ + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */ + >; + }; + + pinctrl_accel: accelirq { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 + >; + }; + + pinctrl_bten: btengrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + + pinctrl_gpio_leds: gpioledgrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_pps: ppsgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 + >; + }; + + pinctrl_reg_wl: regwlgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x41 + >; + }; + + pinctrl_reg_usb1_en: regusb1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 + >; + }; + + pinctrl_reg_usb2_en: regusb2grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x41 + >; + }; + + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 + MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6 + >; + }; + + pinctrl_spi2: spi2grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + >; + }; + + pinctrl_uart2_gpio: uart2grpgpio { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x40000104 /*TERM*/ + MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x40000104 /*RS485*/ + MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2 0x40000104 /*HALF*/ + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + MX8MM_IOMUXC_ECSPI1_MISO_GPIO5_IO8 0x140 + MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x140 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4 + MX8MM_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0x1d0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; +};
The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development kits comprised of a GW700x SoM and a Baseboard. The GW700x SoM contains: - IMX8MM SoC - LPDDR4 DRAM - eMMC FLASH - Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor) - GbE PHY connected to the IMX8MM FEC - Power Management IC The GW71xx Baseboard contains: - 1x MiniPCIe Socket with USB2.0, PCIe, and SIM - 1x RJ45 GbE (IMX8MM FEC) - PCIe Clock generator - GPS and accelerometer - 1x USB 2.0 Front Panel connector - wide range power supply The GW72xx Baseboard contains: - 2x MiniPCIe Socket with USB2.0, PCIe, and SIM - 2x RJ45 GbE (IMX8MM FEC and LAN743x) - 1x MicroSD connector - 1x USB 2.0 Front Panel connector - 1x SPI connector - PCIe Clock generator - GPS and accelerometer - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) - wide range power supply The GW73xx Baseboard contains: - 3x MiniPCIe Socket with USB2.0, PCIe, and SIM - 2x RJ45 GbE (IMX8MM FEC and LAN743x) - 1x MicroSD connector - 1x USB 2.0 Front Panel connector - 1x SPI connector - WiFi/BT - PCIe Clock generator - GPS and accelerometer - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) - wide range power supply Signed-off-by: Tim Harvey <tharvey@gateworks.com> --- arch/arm64/boot/dts/freescale/Makefile | 3 + .../boot/dts/freescale/imx8mm-venice-gw700x.dtsi | 482 +++++++++++++++++++++ .../boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts | 19 + .../boot/dts/freescale/imx8mm-venice-gw71xx.dtsi | 186 ++++++++ .../boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts | 20 + .../boot/dts/freescale/imx8mm-venice-gw72xx.dtsi | 311 +++++++++++++ .../boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts | 19 + .../boot/dts/freescale/imx8mm-venice-gw73xx.dtsi | 363 ++++++++++++++++ 8 files changed, 1403 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi