@@ -90,4 +90,6 @@ extern int ocpi_enable(void);
static inline int ocpi_enable(void) { return 0; }
#endif
+extern u32 omap1_read_reset_sources(void);
+
#endif /* __ARCH_ARM_MACH_OMAP1_COMMON_H */
@@ -8,8 +8,22 @@
#include <mach/hardware.h>
+#include "iomap.h"
#include "common.h"
+/* ARM_SYSST bit shifts related to SoC reset sources */
+#define ARM_SYSST_POR_SHIFT 5
+#define ARM_SYSST_EXT_RST_SHIFT 4
+#define ARM_SYSST_ARM_WDRST_SHIFT 2
+#define ARM_SYSST_GLOB_SWRST_SHIFT 1
+
+/* Standardized reset source bits (across all OMAP SoCs) */
+#define OMAP_GLOBAL_COLD_RST_SRC_ID_SHIFT 0
+#define OMAP_GLOBAL_WARM_RST_SRC_ID_SHIFT 1
+#define OMAP_MPU_WD_RST_SRC_ID_SHIFT 3
+#define OMAP_EXTWARM_RST_SRC_ID_SHIFT 5
+
+
void omap1_restart(char mode, const char *cmd)
{
/*
@@ -23,3 +37,28 @@ void omap1_restart(char mode, const char *cmd)
omap_writew(1, ARM_RSTCT1);
}
+
+/**
+ * omap1_read_reset_sources - return the source of the SoC's last reset
+ *
+ * Returns bits that represent the last reset source for the SoC. The
+ * format is standardized across OMAPs for use by the OMAP watchdog.
+ */
+u32 omap1_read_reset_sources(void)
+{
+ int ret = 0;
+ u16 rs;
+
+ rs = __raw_readw(OMAP1_IO_ADDRESS(ARM_SYSST));
+
+ if (rs & (1 << ARM_SYSST_POR_SHIFT))
+ ret |= 1 << OMAP_GLOBAL_COLD_RST_SRC_ID_SHIFT;
+ if (rs & (1 << ARM_SYSST_EXT_RST_SHIFT))
+ ret |= 1 << OMAP_EXTWARM_RST_SRC_ID_SHIFT;
+ if (rs & (1 << ARM_SYSST_ARM_WDRST_SHIFT))
+ ret |= 1 << OMAP_MPU_WD_RST_SRC_ID_SHIFT;
+ if (rs & (1 << ARM_SYSST_GLOB_SWRST_SHIFT))
+ ret |= 1 << OMAP_GLOBAL_WARM_RST_SRC_ID_SHIFT;
+
+ return ret;
+}
On OMAP1, the existing OMAP watchdog driver reads a register directly from a non-watchdog IP block. It also does not convert the register's contents into the standard WDIOF_* bits expected from the GETBOOTSTATUS ioctl(). To move towards fixing these problems, create an function in arch/arm/mach-omap1 to return the reset source data. A subsequent patch will provide this function to the watchdog driver via platform_data. In the long term, the best approach would be to move this function to a new OMAP1 driver that handles access to the OMAP1 Clock Generation and Reset Management IP block. Then no platform_data would be needed. Signed-off-by: Paul Walmsley <paul@pwsan.com> --- arch/arm/mach-omap1/common.h | 2 ++ arch/arm/mach-omap1/reset.c | 39 +++++++++++++++++++++++++++++++++++++++ 2 files changed, 41 insertions(+)