diff mbox

[v2,2/5] mfd: add Ricoh RN5T567 PMIC support

Message ID 20160608010429.19618-3-stefan@agner.ch (mailing list archive)
State New, archived
Headers show

Commit Message

Stefan Agner June 8, 2016, 1:04 a.m. UTC
The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:

+ DCDC4
+ Slightly different output voltage/currents
+ 32kHz Output
- ADC/Charger capabilities

Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
 Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++-------
 drivers/mfd/Kconfig                               |  7 +++---
 drivers/mfd/rn5t618.c                             | 26 +++++++++++++++++------
 include/linux/mfd/rn5t618.h                       | 12 +++++++++++
 4 files changed, 46 insertions(+), 18 deletions(-)

Comments

Rob Herring (Arm) June 8, 2016, 8:22 p.m. UTC | #1
On Tue, Jun 07, 2016 at 06:04:26PM -0700, Stefan Agner wrote:
> The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
> the differences are:
> 
> + DCDC4
> + Slightly different output voltage/currents
> + 32kHz Output
> - ADC/Charger capabilities
> 
> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
>  Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++-------
>  drivers/mfd/Kconfig                               |  7 +++---
>  drivers/mfd/rn5t618.c                             | 26 +++++++++++++++++------
>  include/linux/mfd/rn5t618.h                       | 12 +++++++++++
>  4 files changed, 46 insertions(+), 18 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt
> index 937785a..5b493ed 100644
> --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt
> +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt
> @@ -1,18 +1,21 @@
> -* Ricoh RN5T618 PMIC
> +* Ricoh RN5T567/RN5T618 PMIC
>  
> -Ricoh RN5T618 is a power management IC which integrates 3 step-down
> -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
> -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled
> -through a I2C interface.
> +Ricoh RN5T567/RN5T618 is a power management IC family which integrates
> +3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and

I count 4?

Otherwise, for the binding:

Acked-by: Rob Herring <robh@kernel.org>
Stefan Agner June 8, 2016, 9:47 p.m. UTC | #2
On 2016-06-08 13:22, Rob Herring wrote:
> On Tue, Jun 07, 2016 at 06:04:26PM -0700, Stefan Agner wrote:
>> The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
>> the differences are:
>>
>> + DCDC4
>> + Slightly different output voltage/currents
>> + 32kHz Output
>> - ADC/Charger capabilities
>>
>> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
>>  Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++-------
>>  drivers/mfd/Kconfig                               |  7 +++---
>>  drivers/mfd/rn5t618.c                             | 26 +++++++++++++++++------
>>  include/linux/mfd/rn5t618.h                       | 12 +++++++++++
>>  4 files changed, 46 insertions(+), 18 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt
>> index 937785a..5b493ed 100644
>> --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt
>> +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt
>> @@ -1,18 +1,21 @@
>> -* Ricoh RN5T618 PMIC
>> +* Ricoh RN5T567/RN5T618 PMIC
>>
>> -Ricoh RN5T618 is a power management IC which integrates 3 step-down
>> -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
>> -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled
>> -through a I2C interface.
>> +Ricoh RN5T567/RN5T618 is a power management IC family which integrates
>> +3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and
> 
> I count 4?

There is actually a third PMIC in this family RC5T619 which has 5, that
is where the number comes from. But that PMIC also has 12 LDO's so the
numbers are a bit a mix and much right now...

If I have to amend something anyway, I will fix that. Otherwise I look
at it as a preparation for the one which adds RC5T619 support :-)

--
Stefan
Lee Jones June 16, 2016, 2:55 p.m. UTC | #3
On Tue, 07 Jun 2016, Stefan Agner wrote:

> The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
> the differences are:
> 
> + DCDC4
> + Slightly different output voltage/currents
> + 32kHz Output
> - ADC/Charger capabilities
> 
> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
>  Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++-------
>  drivers/mfd/Kconfig                               |  7 +++---
>  drivers/mfd/rn5t618.c                             | 26 +++++++++++++++++------
>  include/linux/mfd/rn5t618.h                       | 12 +++++++++++
>  4 files changed, 46 insertions(+), 18 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt
> index 937785a..5b493ed 100644
> --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt
> +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt
> @@ -1,18 +1,21 @@
> -* Ricoh RN5T618 PMIC
> +* Ricoh RN5T567/RN5T618 PMIC
>  
> -Ricoh RN5T618 is a power management IC which integrates 3 step-down
> -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
> -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled
> -through a I2C interface.
> +Ricoh RN5T567/RN5T618 is a power management IC family which integrates
> +3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and
> +a watchdog timer. The RN5T618 provides additionally a Li-ion battery
> +charger, fuel gauge and an ADC. It can be controlled through a I2C

Nit: s/a I2C/an I2C/

> +interface.
>  
>  Required properties:
> - - compatible: should be "ricoh,rn5t618"
> + - compatible: must be one of
> +		"ricoh,rn5t567"
> +		"ricoh,rn5t618"
>   - reg: the I2C slave address of the device
>  
>  Sub-nodes:
>   - regulators: the node is required if the regulator functionality is
> -   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1,
> -   LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
> +   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4
> +   (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
>     The common bindings for each individual regulator can be found in:
>     Documentation/devicetree/bindings/regulator/regulator.txt
>  
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 1bcf601..ff031a7 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -852,13 +852,14 @@ config MFD_RK808
>  	  including interrupts, RTC, LDO & DCDC regulators, and onkey.
>  
>  config MFD_RN5T618
> -	tristate "Ricoh RN5T5618 PMIC"
> +	tristate "Ricoh RN5T567/618 PMIC"
>  	depends on I2C
> +	depends on OF
>  	select MFD_CORE
>  	select REGMAP_I2C
>  	help
> -	  Say yes here to add support for the Ricoh RN5T618 PMIC. This
> -	  driver provides common support for accessing the device,
> +	  Say yes here to add support for the Ricoh RN5T567 or R5T618 PMIC.
> +	  This driver provides common support for accessing the device,
>  	  additional drivers must be enabled in order to use the
>  	  functionality of the device.
>  
> diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c
> index 0ad51d7..7607ced 100644
> --- a/drivers/mfd/rn5t618.c
> +++ b/drivers/mfd/rn5t618.c
> @@ -2,6 +2,7 @@
>   * MFD core driver for Ricoh RN5T618 PMIC
>   *
>   * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com>
> + * Copyright (C) 2016 Toradex AG
>   *
>   * This program is free software; you can redistribute it and/or
>   * modify it under the terms of the GNU General Public License
> @@ -15,6 +16,7 @@
>  #include <linux/mfd/core.h>
>  #include <linux/mfd/rn5t618.h>
>  #include <linux/module.h>
> +#include <linux/of_device.h>
>  #include <linux/regmap.h>
>  
>  static const struct mfd_cell rn5t618_cells[] = {
> @@ -59,12 +61,26 @@ static void rn5t618_power_off(void)
>  			   RN5T618_SLPCNT_SWPWROFF, RN5T618_SLPCNT_SWPWROFF);
>  }
>  
> +static const struct of_device_id rn5t618_of_match[] = {
> +	{ .compatible = "ricoh,rn5t567", .data = (void *)RN5T567 },
> +	{ .compatible = "ricoh,rn5t618", .data = (void *)RN5T618 },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, rn5t618_of_match);
> +
>  static int rn5t618_i2c_probe(struct i2c_client *i2c,
>  			     const struct i2c_device_id *id)
>  {
> +	const struct of_device_id *of_id =
> +		of_match_device(rn5t618_of_match, &i2c->dev);

I'd prefer you did the call *after* the variable declarations.

>  	struct rn5t618 *priv;
>  	int ret;

So here ->
> +	if (!of_id) {
> +		dev_err(&i2c->dev, "Failed to find matching dt id\n");

s/dt id/DT ID/
> +		return -EINVAL;
> +	}
> +
>  	priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL);
>  	if (!priv)
>  		return -ENOMEM;
> @@ -78,6 +94,8 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c,
>  		return ret;
>  	}
>  
> +	priv->variant = (long)of_id->data;
> +

Why here and not directly after the of_id check?

>  	ret = devm_mfd_add_devices(&i2c->dev, -1, rn5t618_cells,
>  				   ARRAY_SIZE(rn5t618_cells), NULL, 0, NULL);
>  	if (ret) {
> @@ -105,12 +123,6 @@ static int rn5t618_i2c_remove(struct i2c_client *i2c)
>  	return 0;
>  }
>  
> -static const struct of_device_id rn5t618_of_match[] = {
> -	{ .compatible = "ricoh,rn5t618" },
> -	{ }
> -};
> -MODULE_DEVICE_TABLE(of, rn5t618_of_match);
> -
>  static const struct i2c_device_id rn5t618_i2c_id[] = {
>  	{ }
>  };
> @@ -129,5 +141,5 @@ static struct i2c_driver rn5t618_i2c_driver = {
>  module_i2c_driver(rn5t618_i2c_driver);
>  
>  MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>");
> -MODULE_DESCRIPTION("Ricoh RN5T618 MFD driver");
> +MODULE_DESCRIPTION("Ricoh RN5T567/618 MFD driver");
>  MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h
> index c72d534..54179c2 100644
> --- a/include/linux/mfd/rn5t618.h
> +++ b/include/linux/mfd/rn5t618.h
> @@ -20,6 +20,7 @@
>  #define RN5T618_OTPVER			0x01
>  #define RN5T618_IODAC			0x02
>  #define RN5T618_VINDAC			0x03
> +#define RN5T618_OUT32KEN		0x05
>  #define RN5T618_CPUCNT			0x06
>  #define RN5T618_PSWR			0x07
>  #define RN5T618_PONHIS			0x09
> @@ -38,6 +39,7 @@
>  #define RN5T618_DC1_SLOT		0x16
>  #define RN5T618_DC2_SLOT		0x17
>  #define RN5T618_DC3_SLOT		0x18
> +#define RN5T618_DC4_SLOT		0x19
>  #define RN5T618_LDO1_SLOT		0x1b
>  #define RN5T618_LDO2_SLOT		0x1c
>  #define RN5T618_LDO3_SLOT		0x1d
> @@ -54,12 +56,16 @@
>  #define RN5T618_DC2CTL2			0x2f
>  #define RN5T618_DC3CTL			0x30
>  #define RN5T618_DC3CTL2			0x31
> +#define RN5T618_DC4CTL			0x32
> +#define RN5T618_DC4CTL2			0x33
>  #define RN5T618_DC1DAC			0x36
>  #define RN5T618_DC2DAC			0x37
>  #define RN5T618_DC3DAC			0x38
> +#define RN5T618_DC4DAC			0x39
>  #define RN5T618_DC1DAC_SLP		0x3b
>  #define RN5T618_DC2DAC_SLP		0x3c
>  #define RN5T618_DC3DAC_SLP		0x3d
> +#define RN5T618_DC4DAC_SLP		0x3e
>  #define RN5T618_DCIREN			0x40
>  #define RN5T618_DCIRQ			0x41
>  #define RN5T618_DCIRMON			0x42
> @@ -221,8 +227,14 @@ enum {
>  	RN5T618_REG_NUM,
>  };
>  
> +enum {
> +	RN5T567 = 0,
> +	RN5T618,
> +};
> +
>  struct rn5t618 {
>  	struct regmap *regmap;
> +	long variant;

What do you use this for?

>  };
>  
>  #endif /* __LINUX_MFD_RN5T618_H */
Stefan Agner June 19, 2016, 12:57 a.m. UTC | #4
On 2016-06-16 07:55, Lee Jones wrote:
> On Tue, 07 Jun 2016, Stefan Agner wrote:
> 
>> The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
>> the differences are:
>>
>> + DCDC4
>> + Slightly different output voltage/currents
>> + 32kHz Output
>> - ADC/Charger capabilities
>>
>> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
>>  Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++-------
>>  drivers/mfd/Kconfig                               |  7 +++---
>>  drivers/mfd/rn5t618.c                             | 26 +++++++++++++++++------
>>  include/linux/mfd/rn5t618.h                       | 12 +++++++++++
>>  4 files changed, 46 insertions(+), 18 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt
>> index 937785a..5b493ed 100644
>> --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt
>> +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt
>> @@ -1,18 +1,21 @@
>> -* Ricoh RN5T618 PMIC
>> +* Ricoh RN5T567/RN5T618 PMIC
>>
>> -Ricoh RN5T618 is a power management IC which integrates 3 step-down
>> -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
>> -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled
>> -through a I2C interface.
>> +Ricoh RN5T567/RN5T618 is a power management IC family which integrates
>> +3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and
>> +a watchdog timer. The RN5T618 provides additionally a Li-ion battery
>> +charger, fuel gauge and an ADC. It can be controlled through a I2C
> 
> Nit: s/a I2C/an I2C/
> 
>> +interface.
>>
>>  Required properties:
>> - - compatible: should be "ricoh,rn5t618"
>> + - compatible: must be one of
>> +		"ricoh,rn5t567"
>> +		"ricoh,rn5t618"
>>   - reg: the I2C slave address of the device
>>
>>  Sub-nodes:
>>   - regulators: the node is required if the regulator functionality is
>> -   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1,
>> -   LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
>> +   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4
>> +   (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
>>     The common bindings for each individual regulator can be found in:
>>     Documentation/devicetree/bindings/regulator/regulator.txt
>>
>> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
>> index 1bcf601..ff031a7 100644
>> --- a/drivers/mfd/Kconfig
>> +++ b/drivers/mfd/Kconfig
>> @@ -852,13 +852,14 @@ config MFD_RK808
>>  	  including interrupts, RTC, LDO & DCDC regulators, and onkey.
>>
>>  config MFD_RN5T618
>> -	tristate "Ricoh RN5T5618 PMIC"
>> +	tristate "Ricoh RN5T567/618 PMIC"
>>  	depends on I2C
>> +	depends on OF
>>  	select MFD_CORE
>>  	select REGMAP_I2C
>>  	help
>> -	  Say yes here to add support for the Ricoh RN5T618 PMIC. This
>> -	  driver provides common support for accessing the device,
>> +	  Say yes here to add support for the Ricoh RN5T567 or R5T618 PMIC.
>> +	  This driver provides common support for accessing the device,
>>  	  additional drivers must be enabled in order to use the
>>  	  functionality of the device.
>>
>> diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c
>> index 0ad51d7..7607ced 100644
>> --- a/drivers/mfd/rn5t618.c
>> +++ b/drivers/mfd/rn5t618.c
>> @@ -2,6 +2,7 @@
>>   * MFD core driver for Ricoh RN5T618 PMIC
>>   *
>>   * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com>
>> + * Copyright (C) 2016 Toradex AG
>>   *
>>   * This program is free software; you can redistribute it and/or
>>   * modify it under the terms of the GNU General Public License
>> @@ -15,6 +16,7 @@
>>  #include <linux/mfd/core.h>
>>  #include <linux/mfd/rn5t618.h>
>>  #include <linux/module.h>
>> +#include <linux/of_device.h>
>>  #include <linux/regmap.h>
>>
>>  static const struct mfd_cell rn5t618_cells[] = {
>> @@ -59,12 +61,26 @@ static void rn5t618_power_off(void)
>>  			   RN5T618_SLPCNT_SWPWROFF, RN5T618_SLPCNT_SWPWROFF);
>>  }
>>
>> +static const struct of_device_id rn5t618_of_match[] = {
>> +	{ .compatible = "ricoh,rn5t567", .data = (void *)RN5T567 },
>> +	{ .compatible = "ricoh,rn5t618", .data = (void *)RN5T618 },
>> +	{ }
>> +};
>> +MODULE_DEVICE_TABLE(of, rn5t618_of_match);
>> +
>>  static int rn5t618_i2c_probe(struct i2c_client *i2c,
>>  			     const struct i2c_device_id *id)
>>  {
>> +	const struct of_device_id *of_id =
>> +		of_match_device(rn5t618_of_match, &i2c->dev);
> 
> I'd prefer you did the call *after* the variable declarations.
> 
>>  	struct rn5t618 *priv;
>>  	int ret;
> 
> So here ->
>> +	if (!of_id) {
>> +		dev_err(&i2c->dev, "Failed to find matching dt id\n");
> 
> s/dt id/DT ID/
>> +		return -EINVAL;
>> +	}
>> +
>>  	priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL);
>>  	if (!priv)
>>  		return -ENOMEM;
>> @@ -78,6 +94,8 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c,
>>  		return ret;
>>  	}
>>
>> +	priv->variant = (long)of_id->data;
>> +
> 
> Why here and not directly after the of_id check?
> 
>>  	ret = devm_mfd_add_devices(&i2c->dev, -1, rn5t618_cells,
>>  				   ARRAY_SIZE(rn5t618_cells), NULL, 0, NULL);
>>  	if (ret) {
>> @@ -105,12 +123,6 @@ static int rn5t618_i2c_remove(struct i2c_client *i2c)
>>  	return 0;
>>  }
>>
>> -static const struct of_device_id rn5t618_of_match[] = {
>> -	{ .compatible = "ricoh,rn5t618" },
>> -	{ }
>> -};
>> -MODULE_DEVICE_TABLE(of, rn5t618_of_match);
>> -
>>  static const struct i2c_device_id rn5t618_i2c_id[] = {
>>  	{ }
>>  };
>> @@ -129,5 +141,5 @@ static struct i2c_driver rn5t618_i2c_driver = {
>>  module_i2c_driver(rn5t618_i2c_driver);
>>
>>  MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>");
>> -MODULE_DESCRIPTION("Ricoh RN5T618 MFD driver");
>> +MODULE_DESCRIPTION("Ricoh RN5T567/618 MFD driver");
>>  MODULE_LICENSE("GPL v2");
>> diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h
>> index c72d534..54179c2 100644
>> --- a/include/linux/mfd/rn5t618.h
>> +++ b/include/linux/mfd/rn5t618.h
>> @@ -20,6 +20,7 @@
>>  #define RN5T618_OTPVER			0x01
>>  #define RN5T618_IODAC			0x02
>>  #define RN5T618_VINDAC			0x03
>> +#define RN5T618_OUT32KEN		0x05
>>  #define RN5T618_CPUCNT			0x06
>>  #define RN5T618_PSWR			0x07
>>  #define RN5T618_PONHIS			0x09
>> @@ -38,6 +39,7 @@
>>  #define RN5T618_DC1_SLOT		0x16
>>  #define RN5T618_DC2_SLOT		0x17
>>  #define RN5T618_DC3_SLOT		0x18
>> +#define RN5T618_DC4_SLOT		0x19
>>  #define RN5T618_LDO1_SLOT		0x1b
>>  #define RN5T618_LDO2_SLOT		0x1c
>>  #define RN5T618_LDO3_SLOT		0x1d
>> @@ -54,12 +56,16 @@
>>  #define RN5T618_DC2CTL2			0x2f
>>  #define RN5T618_DC3CTL			0x30
>>  #define RN5T618_DC3CTL2			0x31
>> +#define RN5T618_DC4CTL			0x32
>> +#define RN5T618_DC4CTL2			0x33
>>  #define RN5T618_DC1DAC			0x36
>>  #define RN5T618_DC2DAC			0x37
>>  #define RN5T618_DC3DAC			0x38
>> +#define RN5T618_DC4DAC			0x39
>>  #define RN5T618_DC1DAC_SLP		0x3b
>>  #define RN5T618_DC2DAC_SLP		0x3c
>>  #define RN5T618_DC3DAC_SLP		0x3d
>> +#define RN5T618_DC4DAC_SLP		0x3e
>>  #define RN5T618_DCIREN			0x40
>>  #define RN5T618_DCIRQ			0x41
>>  #define RN5T618_DCIRMON			0x42
>> @@ -221,8 +227,14 @@ enum {
>>  	RN5T618_REG_NUM,
>>  };
>>
>> +enum {
>> +	RN5T567 = 0,
>> +	RN5T618,
>> +};
>> +
>>  struct rn5t618 {
>>  	struct regmap *regmap;
>> +	long variant;
> 
> What do you use this for?

This is used in the regulator driver to detect which variant we are
dealing with...

Ack on all the other stuff, will send a v3 for this.

--
Stefan

> 
>>  };
>>
>>  #endif /* __LINUX_MFD_RN5T618_H */
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt
index 937785a..5b493ed 100644
--- a/Documentation/devicetree/bindings/mfd/rn5t618.txt
+++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt
@@ -1,18 +1,21 @@ 
-* Ricoh RN5T618 PMIC
+* Ricoh RN5T567/RN5T618 PMIC
 
-Ricoh RN5T618 is a power management IC which integrates 3 step-down
-DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
-fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled
-through a I2C interface.
+Ricoh RN5T567/RN5T618 is a power management IC family which integrates
+3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and
+a watchdog timer. The RN5T618 provides additionally a Li-ion battery
+charger, fuel gauge and an ADC. It can be controlled through a I2C
+interface.
 
 Required properties:
- - compatible: should be "ricoh,rn5t618"
+ - compatible: must be one of
+		"ricoh,rn5t567"
+		"ricoh,rn5t618"
  - reg: the I2C slave address of the device
 
 Sub-nodes:
  - regulators: the node is required if the regulator functionality is
-   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1,
-   LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
+   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4
+   (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
    The common bindings for each individual regulator can be found in:
    Documentation/devicetree/bindings/regulator/regulator.txt
 
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 1bcf601..ff031a7 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -852,13 +852,14 @@  config MFD_RK808
 	  including interrupts, RTC, LDO & DCDC regulators, and onkey.
 
 config MFD_RN5T618
-	tristate "Ricoh RN5T5618 PMIC"
+	tristate "Ricoh RN5T567/618 PMIC"
 	depends on I2C
+	depends on OF
 	select MFD_CORE
 	select REGMAP_I2C
 	help
-	  Say yes here to add support for the Ricoh RN5T618 PMIC. This
-	  driver provides common support for accessing the device,
+	  Say yes here to add support for the Ricoh RN5T567 or R5T618 PMIC.
+	  This driver provides common support for accessing the device,
 	  additional drivers must be enabled in order to use the
 	  functionality of the device.
 
diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c
index 0ad51d7..7607ced 100644
--- a/drivers/mfd/rn5t618.c
+++ b/drivers/mfd/rn5t618.c
@@ -2,6 +2,7 @@ 
  * MFD core driver for Ricoh RN5T618 PMIC
  *
  * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com>
+ * Copyright (C) 2016 Toradex AG
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -15,6 +16,7 @@ 
 #include <linux/mfd/core.h>
 #include <linux/mfd/rn5t618.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/regmap.h>
 
 static const struct mfd_cell rn5t618_cells[] = {
@@ -59,12 +61,26 @@  static void rn5t618_power_off(void)
 			   RN5T618_SLPCNT_SWPWROFF, RN5T618_SLPCNT_SWPWROFF);
 }
 
+static const struct of_device_id rn5t618_of_match[] = {
+	{ .compatible = "ricoh,rn5t567", .data = (void *)RN5T567 },
+	{ .compatible = "ricoh,rn5t618", .data = (void *)RN5T618 },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, rn5t618_of_match);
+
 static int rn5t618_i2c_probe(struct i2c_client *i2c,
 			     const struct i2c_device_id *id)
 {
+	const struct of_device_id *of_id =
+		of_match_device(rn5t618_of_match, &i2c->dev);
 	struct rn5t618 *priv;
 	int ret;
 
+	if (!of_id) {
+		dev_err(&i2c->dev, "Failed to find matching dt id\n");
+		return -EINVAL;
+	}
+
 	priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
@@ -78,6 +94,8 @@  static int rn5t618_i2c_probe(struct i2c_client *i2c,
 		return ret;
 	}
 
+	priv->variant = (long)of_id->data;
+
 	ret = devm_mfd_add_devices(&i2c->dev, -1, rn5t618_cells,
 				   ARRAY_SIZE(rn5t618_cells), NULL, 0, NULL);
 	if (ret) {
@@ -105,12 +123,6 @@  static int rn5t618_i2c_remove(struct i2c_client *i2c)
 	return 0;
 }
 
-static const struct of_device_id rn5t618_of_match[] = {
-	{ .compatible = "ricoh,rn5t618" },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, rn5t618_of_match);
-
 static const struct i2c_device_id rn5t618_i2c_id[] = {
 	{ }
 };
@@ -129,5 +141,5 @@  static struct i2c_driver rn5t618_i2c_driver = {
 module_i2c_driver(rn5t618_i2c_driver);
 
 MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>");
-MODULE_DESCRIPTION("Ricoh RN5T618 MFD driver");
+MODULE_DESCRIPTION("Ricoh RN5T567/618 MFD driver");
 MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h
index c72d534..54179c2 100644
--- a/include/linux/mfd/rn5t618.h
+++ b/include/linux/mfd/rn5t618.h
@@ -20,6 +20,7 @@ 
 #define RN5T618_OTPVER			0x01
 #define RN5T618_IODAC			0x02
 #define RN5T618_VINDAC			0x03
+#define RN5T618_OUT32KEN		0x05
 #define RN5T618_CPUCNT			0x06
 #define RN5T618_PSWR			0x07
 #define RN5T618_PONHIS			0x09
@@ -38,6 +39,7 @@ 
 #define RN5T618_DC1_SLOT		0x16
 #define RN5T618_DC2_SLOT		0x17
 #define RN5T618_DC3_SLOT		0x18
+#define RN5T618_DC4_SLOT		0x19
 #define RN5T618_LDO1_SLOT		0x1b
 #define RN5T618_LDO2_SLOT		0x1c
 #define RN5T618_LDO3_SLOT		0x1d
@@ -54,12 +56,16 @@ 
 #define RN5T618_DC2CTL2			0x2f
 #define RN5T618_DC3CTL			0x30
 #define RN5T618_DC3CTL2			0x31
+#define RN5T618_DC4CTL			0x32
+#define RN5T618_DC4CTL2			0x33
 #define RN5T618_DC1DAC			0x36
 #define RN5T618_DC2DAC			0x37
 #define RN5T618_DC3DAC			0x38
+#define RN5T618_DC4DAC			0x39
 #define RN5T618_DC1DAC_SLP		0x3b
 #define RN5T618_DC2DAC_SLP		0x3c
 #define RN5T618_DC3DAC_SLP		0x3d
+#define RN5T618_DC4DAC_SLP		0x3e
 #define RN5T618_DCIREN			0x40
 #define RN5T618_DCIRQ			0x41
 #define RN5T618_DCIRMON			0x42
@@ -221,8 +227,14 @@  enum {
 	RN5T618_REG_NUM,
 };
 
+enum {
+	RN5T567 = 0,
+	RN5T618,
+};
+
 struct rn5t618 {
 	struct regmap *regmap;
+	long variant;
 };
 
 #endif /* __LINUX_MFD_RN5T618_H */