| Message ID | 20160726203041.29366-13-maxime.ripard@free-electrons.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Maxime, On 26/07/16 21:30, Maxime Ripard wrote: > From: Andre Przywara <andre.przywara@arm.com> > > The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores > and the typical tablet / TV box peripherals. > The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of > the peripherals and the memory map. > Although the cores are proper 64-bit ones, the whole SoC is actually > limited to 4GB (including all the supported DRAM), so we use 32-bit > address and size cells. This has the nice feature of us being able to > reuse the DT for 32-bit kernels as well. > This .dtsi lists the hardware that we support so far. > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > Acked-by: Rob Herring <robh@kernel.org> > [Maxime: Convert to CCU binding, drop the MMC support for now] > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> > --- > Documentation/devicetree/bindings/arm/sunxi.txt | 1 + > MAINTAINERS | 1 + > arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 273 ++++++++++++++++++++++++ > 3 files changed, 275 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi > > diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt > index 7e79fcc36b0d..7e59d8ba86af 100644 > --- a/Documentation/devicetree/bindings/arm/sunxi.txt > +++ b/Documentation/devicetree/bindings/arm/sunxi.txt > @@ -14,3 +14,4 @@ using one of the following compatible strings: > allwinner,sun8i-a83t > allwinner,sun8i-h3 > allwinner,sun9i-a80 > + allwinner,sun50i-a64 > diff --git a/MAINTAINERS b/MAINTAINERS > index 7304d2e37a98..440490126bfb 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -955,6 +955,7 @@ M: Chen-Yu Tsai <wens@csie.org> > L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) > S: Maintained > N: sun[x456789]i > +F: arch/arm64/boot/dts/allwinner/ > > ARM/Allwinner SoC Clock Support > M: Emilio López <emilio@elopez.com.ar> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi > new file mode 100644 > index 000000000000..636165d75373 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi > @@ -0,0 +1,273 @@ > +/* > + * Copyright (C) 2016 ARM Ltd. > + * based on the Allwinner H3 dtsi: > + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +#include <dt-bindings/clock/sun50i-a64-ccu.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/pinctrl/sun4i-a10.h> > +#include <dt-bindings/reset/sun50i-a64-ccu.h> > + > +/ { > + interrupt-parent = <&gic>; > + #address-cells = <1>; > + #size-cells = <1>; > + > + cpus { > + #address-cells = <1>; > + #size-cells = <0>; > + > + cpu@0 { > + compatible = "arm,cortex-a53", "arm,armv8"; > + device_type = "cpu"; > + reg = <0>; > + enable-method = "psci"; > + }; > + > + cpu@1 { > + compatible = "arm,cortex-a53", "arm,armv8"; > + device_type = "cpu"; > + reg = <1>; > + enable-method = "psci"; > + }; > + > + cpu@2 { > + compatible = "arm,cortex-a53", "arm,armv8"; > + device_type = "cpu"; > + reg = <2>; > + enable-method = "psci"; > + }; > + > + cpu@3 { > + compatible = "arm,cortex-a53", "arm,armv8"; > + device_type = "cpu"; > + reg = <3>; > + enable-method = "psci"; > + }; > + }; > + > + psci { > + compatible = "arm,psci-0.2"; > + method = "smc"; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 13 > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > + <GIC_PPI 14 > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > + <GIC_PPI 11 > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > + <GIC_PPI 10 > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > + }; Can you add a PMU node here? Or shall I send a patch on top of it? It would be: pmu { compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3"; interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; }; This enables perf to use hardware counters (for cycles and instructions, for instance). > + > + clocks { > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + osc24M: osc24M_clk { > + #clock-cells = <0>; > + compatible = "fixed-clock"; > + clock-frequency = <24000000>; > + clock-output-names = "osc24M"; > + }; > + > + osc32k: osc32k_clk { > + #clock-cells = <0>; > + compatible = "fixed-clock"; > + clock-frequency = <32768>; > + clock-output-names = "osc32k"; > + }; > + }; Can you remove this "clocks" node and put the two subnodes directly onto the top level? I know that putting clocks into a subnode is quite wide spread, but it does not represent any hardware hierarchy, especially in this fixed-clock case. So if we can (and it is easy here!) we should avoid any clocks subnode. (Yes, I know that this was in my original DT as well, but Mark Rutland convinced me of this.) Cheers, Andre. > + > + soc { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + ccu: clock@01c20000 { > + compatible = "allwinner,sun50i-a64-ccu"; > + reg = <0x01c20000 0x400>; > + clocks = <&osc24M>, <&osc32k>; > + clock-names = "hosc", "losc"; > + #clock-cells = <1>; > + #reset-cells = <1>; > + }; > + > + pio: pinctrl@1c20800 { > + compatible = "allwinner,sun50i-a64-pinctrl"; > + reg = <0x01c20800 0x400>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_A64_BUS_PIO>; > + gpio-controller; > + #gpio-cells = <3>; > + interrupt-controller; > + #interrupt-cells = <2>; > + > + i2c1_pins: i2c1_pins { > + allwinner,pins = "PH2", "PH3"; > + allwinner,function = "i2c1"; > + allwinner,drive = <SUN4I_PINCTRL_10_MA>; > + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; > + }; > + > + uart0_pins_a: uart0@0 { > + allwinner,pins = "PB8", "PB9"; > + allwinner,function = "uart0"; > + allwinner,drive = <SUN4I_PINCTRL_10_MA>; > + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; > + }; > + }; > + > + uart0: serial@1c28000 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x01c28000 0x400>; > + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_A64_BUS_UART0>; > + resets = <&ccu RST_A64_BUS_UART0>; > + status = "disabled"; > + }; > + > + uart1: serial@1c28400 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x01c28400 0x400>; > + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_A64_BUS_UART1>; > + resets = <&ccu RST_A64_BUS_UART1>; > + status = "disabled"; > + }; > + > + uart2: serial@1c28800 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x01c28800 0x400>; > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_A64_BUS_UART2>; > + resets = <&ccu RST_A64_BUS_UART2>; > + status = "disabled"; > + }; > + > + uart3: serial@1c28c00 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x01c28c00 0x400>; > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_A64_BUS_UART3>; > + resets = <&ccu RST_A64_BUS_UART3>; > + status = "disabled"; > + }; > + > + uart4: serial@1c29000 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x01c29000 0x400>; > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_A64_BUS_UART4>; > + resets = <&ccu RST_A64_BUS_UART4>; > + status = "disabled"; > + }; > + > + rtc: rtc@1f00000 { > + compatible = "allwinner,sun6i-a31-rtc"; > + reg = <0x01f00000 0x54>; > + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + i2c0: i2c@1c2ac00 { > + compatible = "allwinner,sun6i-a31-i2c"; > + reg = <0x01c2ac00 0x400>; > + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_A64_BUS_I2C0>; > + resets = <&ccu RST_A64_BUS_I2C0>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + i2c1: i2c@1c2b000 { > + compatible = "allwinner,sun6i-a31-i2c"; > + reg = <0x01c2b000 0x400>; > + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_A64_BUS_I2C1>; > + resets = <&ccu RST_A64_BUS_I2C1>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + i2c2: i2c@1c2b400 { > + compatible = "allwinner,sun6i-a31-i2c"; > + reg = <0x01c2b400 0x400>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_A64_BUS_I2C2>; > + resets = <&ccu RST_A64_BUS_I2C2>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + gic: interrupt-controller@1c81000 { > + compatible = "arm,gic-400"; > + reg = <0x01c81000 0x1000>, > + <0x01c82000 0x2000>, > + <0x01c84000 0x2000>, > + <0x01c86000 0x2000>; > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > + interrupt-controller; > + #interrupt-cells = <3>; > + }; > + }; > +}; >
Hi, On Thu, Sep 08, 2016 at 09:41:10AM +0100, Andre Przywara wrote: > > + timer { > > + compatible = "arm,armv8-timer"; > > + interrupts = <GIC_PPI 13 > > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > > + <GIC_PPI 14 > > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > > + <GIC_PPI 11 > > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > > + <GIC_PPI 10 > > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > > + }; > > Can you add a PMU node here? Or shall I send a patch on top of it? > It would be: > > pmu { > compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3"; > interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; > interrupt-affinity = <&cpu0>, > <&cpu1>, > <&cpu2>, > <&cpu3>; > }; > > This enables perf to use hardware counters (for cycles and instructions, > for instance). > > > + > > + clocks { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges; > > + > > + osc24M: osc24M_clk { > > + #clock-cells = <0>; > > + compatible = "fixed-clock"; > > + clock-frequency = <24000000>; > > + clock-output-names = "osc24M"; > > + }; > > + > > + osc32k: osc32k_clk { > > + #clock-cells = <0>; > > + compatible = "fixed-clock"; > > + clock-frequency = <32768>; > > + clock-output-names = "osc32k"; > > + }; > > + }; > > Can you remove this "clocks" node and put the two subnodes directly onto > the top level? > I know that putting clocks into a subnode is quite wide spread, but it > does not represent any hardware hierarchy, especially in this > fixed-clock case. > So if we can (and it is easy here!) we should avoid any clocks subnode. > > (Yes, I know that this was in my original DT as well, but Mark Rutland > convinced me of this.) I'll do those changes before sending the new version. Maxime
diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt index 7e79fcc36b0d..7e59d8ba86af 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.txt +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -14,3 +14,4 @@ using one of the following compatible strings: allwinner,sun8i-a83t allwinner,sun8i-h3 allwinner,sun9i-a80 + allwinner,sun50i-a64 diff --git a/MAINTAINERS b/MAINTAINERS index 7304d2e37a98..440490126bfb 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -955,6 +955,7 @@ M: Chen-Yu Tsai <wens@csie.org> L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) S: Maintained N: sun[x456789]i +F: arch/arm64/boot/dts/allwinner/ ARM/Allwinner SoC Clock Support M: Emilio López <emilio@elopez.com.ar> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi new file mode 100644 index 000000000000..636165d75373 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -0,0 +1,273 @@ +/* + * Copyright (C) 2016 ARM Ltd. + * based on the Allwinner H3 dtsi: + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/clock/sun50i-a64-ccu.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> +#include <dt-bindings/reset/sun50i-a64-ccu.h> + +/ { + interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + reg = <0>; + enable-method = "psci"; + }; + + cpu@1 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + reg = <1>; + enable-method = "psci"; + }; + + cpu@2 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + reg = <2>; + enable-method = "psci"; + }; + + cpu@3 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + reg = <3>; + enable-method = "psci"; + }; + }; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + osc24M: osc24M_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "osc24M"; + }; + + osc32k: osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "osc32k"; + }; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ccu: clock@01c20000 { + compatible = "allwinner,sun50i-a64-ccu"; + reg = <0x01c20000 0x400>; + clocks = <&osc24M>, <&osc32k>; + clock-names = "hosc", "losc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + pio: pinctrl@1c20800 { + compatible = "allwinner,sun50i-a64-pinctrl"; + reg = <0x01c20800 0x400>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_A64_BUS_PIO>; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <2>; + + i2c1_pins: i2c1_pins { + allwinner,pins = "PH2", "PH3"; + allwinner,function = "i2c1"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + uart0_pins_a: uart0@0 { + allwinner,pins = "PB8", "PB9"; + allwinner,function = "uart0"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + }; + + uart0: serial@1c28000 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28000 0x400>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_A64_BUS_UART0>; + resets = <&ccu RST_A64_BUS_UART0>; + status = "disabled"; + }; + + uart1: serial@1c28400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28400 0x400>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_A64_BUS_UART1>; + resets = <&ccu RST_A64_BUS_UART1>; + status = "disabled"; + }; + + uart2: serial@1c28800 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28800 0x400>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_A64_BUS_UART2>; + resets = <&ccu RST_A64_BUS_UART2>; + status = "disabled"; + }; + + uart3: serial@1c28c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28c00 0x400>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_A64_BUS_UART3>; + resets = <&ccu RST_A64_BUS_UART3>; + status = "disabled"; + }; + + uart4: serial@1c29000 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29000 0x400>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_A64_BUS_UART4>; + resets = <&ccu RST_A64_BUS_UART4>; + status = "disabled"; + }; + + rtc: rtc@1f00000 { + compatible = "allwinner,sun6i-a31-rtc"; + reg = <0x01f00000 0x54>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + }; + + i2c0: i2c@1c2ac00 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2ac00 0x400>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_A64_BUS_I2C0>; + resets = <&ccu RST_A64_BUS_I2C0>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c@1c2b000 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b000 0x400>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_A64_BUS_I2C1>; + resets = <&ccu RST_A64_BUS_I2C1>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@1c2b400 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b400 0x400>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_A64_BUS_I2C2>; + resets = <&ccu RST_A64_BUS_I2C2>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + gic: interrupt-controller@1c81000 { + compatible = "arm,gic-400"; + reg = <0x01c81000 0x1000>, + <0x01c82000 0x2000>, + <0x01c84000 0x2000>, + <0x01c86000 0x2000>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + interrupt-controller; + #interrupt-cells = <3>; + }; + }; +};