diff mbox

[1/2] ARM64: dts: meson-gxbb: add MMC support

Message ID 20160803003045.24980-1-khilman@baylibre.com (mailing list archive)
State New, archived
Headers show

Commit Message

Kevin Hilman Aug. 3, 2016, 12:30 a.m. UTC
Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.

Signed-off-by: Kevin Hilman <khilman@baylibre.com>
---
 .../devicetree/bindings/mmc/amlogic,meson-gxbb.txt | 29 +++++++++
 .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 74 ++++++++++++++++++++++
 arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi   | 71 +++++++++++++++++++++
 arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi        | 30 ++++++++-
 4 files changed, 203 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt

Comments

Kevin Hilman Aug. 3, 2016, 10:13 p.m. UTC | #1
On Tue, Aug 2, 2016 at 5:30 PM, Kevin Hilman <khilman@baylibre.com> wrote:
> Add binding and basic support for the SD/eMMC controller on Amlogic
> S905/GXBB devices.
>
> Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Oops, please disregard.  Sent due to a missing "--dry-run" with
git-send-email. :(

Kevin
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt
new file mode 100644
index 000000000000..2bfdf47018c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt
@@ -0,0 +1,29 @@ 
+Amlogic SD / eMMC controller for S905/GXBB family SoCs
+
+The MMC 5.1 compliant host controller on Amlogic provides the
+interface for SD, eMMC and SDIO devices.
+
+This file documents the properties in addition to those available in
+the MMC core bindings, documented by mmc.txt.
+
+Required properties:
+- compatible : contains "amlogic,meson-gxbb"
+- clocks     : A list of phandle + clock-specifier pairs for the clocks listed in clock-names.
+- clock-names: Should contain the following:
+	"core" - Main peripheral bus clock
+	"clkin0" - Parent clock of internal mux
+	"clkin1" - Other parent clock of internal mux
+  The driver has an interal mux clock which switches between clkin0 and clkin1 depending on the
+  clock rate requested by the MMC core.
+
+Example:
+
+	sd_emmc_a: mmc@70000 {
+        	compatible = "amlogic,meson-gxbb-mmc";
+		reg = <0x0 0x70000 0x0 0x2000>;
+                interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
+		clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>;
+		clock-names = "core", "clkin0", "clkin1";
+		pinctrl-0 = <&emmc_pins>;
+	};
+
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 90a84c514d3d..a49f7f77eb34 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -73,6 +73,45 @@ 
 			default-state = "off";
 		};
 	};
+
+	mmc_iv: gpio-regulator {
+		compatible = "regulator-gpio";
+
+		regulator-name = "mmc-gpio-supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+		gpio-states = <0 1>;
+	
+		/*
+		 * Based on ODROID-C2 schematics:
+		 * signal name: IO_TF_3V3N_1V8, GPIOAO bit 3
+		 */
+		states = <3300000 0
+		          1800000 1>;
+	};
+
+	vcc1v8: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	vcc3v3: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
 };
 
 &uart_AO {
@@ -87,3 +126,38 @@ 
 	pinctrl-names = "default";
 };
 
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&mmc_iv>;
+	voltage-ranges = <1800 3300>;
+};
+
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	cap-sd-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	voltage-ranges = <1800 3300>;
+	vmmc-supply = <&vcc3v3>;
+	vmmcq-sumpply = <&vcc1v8>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index f4f30f674b4c..63d95d136aec 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -57,6 +57,42 @@ 
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
 	};
+
+	mmc_iv: gpio-regulator {
+		compatible = "regulator-gpio";
+
+		regulator-name = "mmc-gpio-supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+		gpio-states = <0 1>;
+
+		/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
+		states = <1800000 0
+		          3300000 1>;
+	};
+
+	vddio_boot: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
 };
 
 /* This UART is brought out to the DB9 connector */
@@ -72,3 +108,38 @@ 
 	pinctrl-names = "default";
 };
 
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	voltage-ranges = <1800 3300>;
+	vmmc-supply = <&mmc_iv>;
+};
+
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	voltage-ranges = <1800 3300>;
+	vmmc-supply = <&vcc_3v3>;
+	vmmcq-sumpply = <&vddio_boot>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 35c8b2beb05c..2e48fa1e0364 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -247,7 +247,8 @@ 
 					mux {
 						groups = "emmc_nand_d07",
 						       "emmc_cmd",
-						       "emmc_clk";
+						       "emmc_clk",
+						       "emmc_ds";
 						function = "emmc";
 					};
 				};
@@ -330,6 +331,33 @@ 
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
+
+			sd_emmc_a: mmc@70000 {
+		        	compatible = "amlogic,meson-gxbb-mmc";
+				reg = <0x0 0x70000 0x0 0x2000>;
+		                interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>;
+				clock-names = "core", "clkin0", "clkin1";
+				status = "disabled";
+			};
+
+			sd_emmc_b: mmc@72000 {
+		        	compatible = "amlogic,meson-gxbb-mmc";
+				reg = <0x0 0x72000 0x0 0x2000>;
+				interrupts = < GIC_SPI 217 IRQ_TYPE_EDGE_RISING >;
+				clocks = <&clkc CLKID_SD_EMMC_B>, <&xtal>, <&clkc CLKID_FCLK_DIV2>;
+				clock-names = "core", "clkin0", "clkin1";
+				status = "disabled";
+			};
+
+			sd_emmc_c: mmc@74000 {
+		        	compatible = "amlogic,meson-gxbb-mmc";
+				reg = <0x0 0x74000 0x0 0x2000>;
+		                interrupts = < GIC_SPI 218 IRQ_TYPE_EDGE_RISING >;
+				clocks = <&clkc CLKID_SD_EMMC_C>, <&xtal>, <&clkc CLKID_FCLK_DIV2>;
+				clock-names = "core", "clkin0", "clkin1";
+				status = "disabled";
+			};
 		};
 
 		ethmac: ethernet@c9410000 {