@@ -83,22 +83,6 @@
allwinner,pins = "PG3";
};
-&i2c1 {
- icn8318: touchscreen@40 {
- compatible = "chipone,icn8318";
- reg = <0x40>;
- interrupt-parent = <&pio>;
- interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
- pinctrl-names = "default";
- pinctrl-0 = <&ts_wake_pin_p66>;
- wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
- touchscreen-size-x = <800>;
- touchscreen-size-y = <480>;
- touchscreen-inverted-x;
- touchscreen-swapped-x-y;
- };
-};
-
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins_a>;
@@ -121,20 +105,26 @@
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
-
- ts_wake_pin_p66: ts_wake_pin@0 {
- allwinner,pins = "PB3";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
};
®_usb0_vbus {
gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
};
+&touchscreen {
+ compatible = "chipone,icn8318";
+ reg = <0x40>;
+ /* The P66 uses a different EINT then the reference design */
+ interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
+ /* The icn8318 binding expects wake-gpios instead of power-gpios */
+ wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-inverted-x;
+ touchscreen-swapped-x-y;
+ status = "okay";
+};
+
&uart1 {
/* The P66 uses the uart pins as gpios */
status = "disabled";
@@ -41,6 +41,7 @@
*/
#include "sunxi-reference-design-tablet.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pwm/pwm.h>
/ {
@@ -84,6 +85,23 @@
};
&i2c1 {
+ /*
+ * The gsl1680 is rated at 400KHz and it will not work reliable at
+ * 100KHz, this has been confirmed on multiple different q8 tablets.
+ * All other devices on this bus are also rated for 400KHz.
+ */
+ clock-frequency = <400000>;
+
+ touchscreen: touchscreen {
+ interrupt-parent = <&pio>;
+ interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; /* EINT11 (PG11) */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_power_pin>;
+ power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+ /* Tablet dts must provide reg and compatible */
+ status = "disabled";
+ };
+
pcf8563: rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
@@ -125,6 +143,13 @@
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
+ ts_power_pin: ts_power_pin {
+ pins = "PB3";
+ function = "gpio_out";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
allwinner,pins = "PG1";
allwinner,function = "gpio_in";
Just like on sun8i all sun5i tablets use the same interrupt and power gpios for their touchscreens. I've checked all known a13 fex files and only the UTOO P66 uses a different gpio for the interrupt. Add a touchscreen node to sun5i-reference-design-tablet.dtsi, which fills in the necessary gpios to avoid duplication in the tablet dts files, just like we do in sun8i-reference-design-tablet.dtsi. This will make future patches adding touchscreen nodes to a13 tablets simpler. Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- Changes in v2: -Use generic pin mux properties "pins", "function", "drive-strength" and "bias-disable" --- arch/arm/boot/dts/sun5i-a13-utoo-p66.dts | 38 ++++++++-------------- .../boot/dts/sun5i-reference-design-tablet.dtsi | 25 ++++++++++++++ 2 files changed, 39 insertions(+), 24 deletions(-)