diff mbox

usb: dwc3: omap: remove devm_request_threaded_irq

Message ID 20161209205508.6456-1-grygorii.strashko@ti.com (mailing list archive)
State New, archived
Headers show

Commit Message

Grygorii Strashko Dec. 9, 2016, 8:55 p.m. UTC
Switch back from devm_request_threaded_irq() to request_threaded_irq() to
avoid races between interrupt handler execution and PM runtime in error
handling code path in probe and in dwc3_omap_remove():

in probe:
...
 err1:
	pm_runtime_put_sync(dev);
^^ PM runtime can race with IRQ handler when deferred probing happening
   due to extcon
	pm_runtime_disable(dev);

	return ret;

in dwc3_omap_remove:
...
	dwc3_omap_disable_irqs(omap);
^^ IRQs are disabled in HW, but handler may still run
	of_platform_depopulate(omap->dev);
	pm_runtime_put_sync(&pdev->dev);
^^ PM runtime can race with IRQ handler
	pm_runtime_disable(&pdev->dev);

	return 0;

So, OMAP DWC3 IRQ need to be disabled end freed before calling
pm_runtime_put() in probe and in dwc3_omap_remove().

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
Hi Tony,

This is reworked patch, so might be it need to be re-tested.

 drivers/usb/dwc3/dwc3-omap.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)

Comments

Tony Lindgren Dec. 9, 2016, 9:59 p.m. UTC | #1
* Grygorii Strashko <grygorii.strashko@ti.com> [161209 12:55]:
> Switch back from devm_request_threaded_irq() to request_threaded_irq() to
> avoid races between interrupt handler execution and PM runtime in error
> handling code path in probe and in dwc3_omap_remove():

Can't you just call disable_irq() on the exit path instead of removing
devm?

Regards,

Tony
Grygorii Strashko Dec. 9, 2016, 10:46 p.m. UTC | #2
On 12/09/2016 03:59 PM, Tony Lindgren wrote:
> * Grygorii Strashko <grygorii.strashko@ti.com> [161209 12:55]:
>> Switch back from devm_request_threaded_irq() to request_threaded_irq() to
>> avoid races between interrupt handler execution and PM runtime in error
>> handling code path in probe and in dwc3_omap_remove():
>
> Can't you just call disable_irq() on the exit path instead of removing
> devm?
>

I can. But what will be the benefit from using devm then?
Tony Lindgren Dec. 9, 2016, 11:04 p.m. UTC | #3
* Grygorii Strashko <grygorii.strashko@ti.com> [161209 14:46]:
> 
> 
> On 12/09/2016 03:59 PM, Tony Lindgren wrote:
> > * Grygorii Strashko <grygorii.strashko@ti.com> [161209 12:55]:
> > > Switch back from devm_request_threaded_irq() to request_threaded_irq() to
> > > avoid races between interrupt handler execution and PM runtime in error
> > > handling code path in probe and in dwc3_omap_remove():
> > 
> > Can't you just call disable_irq() on the exit path instead of removing
> > devm?
> > 
> 
> I can. But what will be the benefit from using devm then?

Hmm good point. Probably the least number of code would be to just
do NOAUTOEN before devm_request_irq(), then only do enable_irq()
just before returning from the probe. After all, we don't really
want the irq running until the probe is done.

I think that would leave out the extra handling from the error
path?

Regards,

Tony
Grygorii Strashko Dec. 9, 2016, 11:32 p.m. UTC | #4
On 12/09/2016 05:04 PM, Tony Lindgren wrote:
> * Grygorii Strashko <grygorii.strashko@ti.com> [161209 14:46]:
>>
>>
>> On 12/09/2016 03:59 PM, Tony Lindgren wrote:
>>> * Grygorii Strashko <grygorii.strashko@ti.com> [161209 12:55]:
>>>> Switch back from devm_request_threaded_irq() to request_threaded_irq() to
>>>> avoid races between interrupt handler execution and PM runtime in error
>>>> handling code path in probe and in dwc3_omap_remove():
>>>
>>> Can't you just call disable_irq() on the exit path instead of removing
>>> devm?
>>>
>>
>> I can. But what will be the benefit from using devm then?
> 
> Hmm good point. Probably the least number of code would be to just
> do NOAUTOEN before devm_request_irq(), then only do enable_irq()
> just before returning from the probe. After all, we don't really
> want the irq running until the probe is done.
> 
> I think that would leave out the extra handling from the error
> path?
> 

Good question here is - do we need this irq to be enabled for sub-device
probing from of_platform_populate()? ;)
Tony Lindgren Dec. 9, 2016, 11:37 p.m. UTC | #5
* Grygorii Strashko <grygorii.strashko@ti.com> [161209 15:32]:
> 
> 
> On 12/09/2016 05:04 PM, Tony Lindgren wrote:
> > * Grygorii Strashko <grygorii.strashko@ti.com> [161209 14:46]:
> >>
> >>
> >> On 12/09/2016 03:59 PM, Tony Lindgren wrote:
> >>> * Grygorii Strashko <grygorii.strashko@ti.com> [161209 12:55]:
> >>>> Switch back from devm_request_threaded_irq() to request_threaded_irq() to
> >>>> avoid races between interrupt handler execution and PM runtime in error
> >>>> handling code path in probe and in dwc3_omap_remove():
> >>>
> >>> Can't you just call disable_irq() on the exit path instead of removing
> >>> devm?
> >>>
> >>
> >> I can. But what will be the benefit from using devm then?
> > 
> > Hmm good point. Probably the least number of code would be to just
> > do NOAUTOEN before devm_request_irq(), then only do enable_irq()
> > just before returning from the probe. After all, we don't really
> > want the irq running until the probe is done.
> > 
> > I think that would leave out the extra handling from the error
> > path?
> > 
> 
> Good question here is - do we need this irq to be enabled for sub-device
> probing from of_platform_populate()? ;)  

No!

Tony
Grygorii Strashko Dec. 9, 2016, 11:44 p.m. UTC | #6
On 12/09/2016 05:37 PM, Tony Lindgren wrote:
> * Grygorii Strashko <grygorii.strashko@ti.com> [161209 15:32]:
>>
>>
>> On 12/09/2016 05:04 PM, Tony Lindgren wrote:
>>> * Grygorii Strashko <grygorii.strashko@ti.com> [161209 14:46]:
>>>>
>>>>
>>>> On 12/09/2016 03:59 PM, Tony Lindgren wrote:
>>>>> * Grygorii Strashko <grygorii.strashko@ti.com> [161209 12:55]:
>>>>>> Switch back from devm_request_threaded_irq() to request_threaded_irq() to
>>>>>> avoid races between interrupt handler execution and PM runtime in error
>>>>>> handling code path in probe and in dwc3_omap_remove():
>>>>>
>>>>> Can't you just call disable_irq() on the exit path instead of removing
>>>>> devm?
>>>>>
>>>>
>>>> I can. But what will be the benefit from using devm then?
>>>
>>> Hmm good point. Probably the least number of code would be to just
>>> do NOAUTOEN before devm_request_irq(), then only do enable_irq()
>>> just before returning from the probe. After all, we don't really
>>> want the irq running until the probe is done.
>>>
>>> I think that would leave out the extra handling from the error
>>> path?
>>>
>>
>> Good question here is - do we need this irq to be enabled for sub-device
>> probing from of_platform_populate()? ;)
>
> No!

Ok, then it should work this way.
diff mbox

Patch

diff --git a/drivers/usb/dwc3/dwc3-omap.c b/drivers/usb/dwc3/dwc3-omap.c
index 29e80cc..79d74f6 100644
--- a/drivers/usb/dwc3/dwc3-omap.c
+++ b/drivers/usb/dwc3/dwc3-omap.c
@@ -511,18 +511,18 @@  static int dwc3_omap_probe(struct platform_device *pdev)
 	/* check the DMA Status */
 	reg = dwc3_omap_readl(omap->base, USBOTGSS_SYSCONFIG);
 
-	ret = devm_request_threaded_irq(dev, omap->irq, dwc3_omap_interrupt,
-					dwc3_omap_interrupt_thread, IRQF_SHARED,
-					"dwc3-omap", omap);
+	ret = request_threaded_irq(omap->irq, dwc3_omap_interrupt,
+				   dwc3_omap_interrupt_thread, IRQF_SHARED,
+				   "dwc3-omap", omap);
 	if (ret) {
 		dev_err(dev, "failed to request IRQ #%d --> %d\n",
 				omap->irq, ret);
-		goto err1;
+		goto err11;
 	}
 
 	ret = dwc3_omap_extcon_register(omap);
 	if (ret < 0)
-		goto err1;
+		goto err11;
 
 	ret = of_platform_populate(node, NULL, NULL, dev);
 	if (ret) {
@@ -538,6 +538,8 @@  static int dwc3_omap_probe(struct platform_device *pdev)
 	extcon_unregister_notifier(omap->edev, EXTCON_USB, &omap->vbus_nb);
 	extcon_unregister_notifier(omap->edev, EXTCON_USB_HOST, &omap->id_nb);
 
+err11:
+	free_irq(omap->irq, omap);
 err1:
 	pm_runtime_put_sync(dev);
 	pm_runtime_disable(dev);
@@ -552,6 +554,7 @@  static int dwc3_omap_remove(struct platform_device *pdev)
 	extcon_unregister_notifier(omap->edev, EXTCON_USB, &omap->vbus_nb);
 	extcon_unregister_notifier(omap->edev, EXTCON_USB_HOST, &omap->id_nb);
 	dwc3_omap_disable_irqs(omap);
+	free_irq(omap->irq, omap);
 	of_platform_depopulate(omap->dev);
 	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);