[v6,2/2] ARM: dts: vf610-zii-dev: Add .dts file for rev. C

Message ID	20170110073555.12178-2-andrew.smirnov@gmail.com (mailing list archive)
State	New, archived
Headers	show Return-Path: <linux-arm-kernel-bounces+patchwork-linux-arm=patchwork.kernel.org@lists.infradead.org> From: Andrey Smirnov <andrew.smirnov@gmail.com> To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v6 2/2] ARM: dts: vf610-zii-dev: Add .dts file for rev. C Date: Mon, 9 Jan 2017 23:35:55 -0800 Message-Id: <20170110073555.12178-2-andrew.smirnov@gmail.com> In-Reply-To: <20170110073555.12178-1-andrew.smirnov@gmail.com> References: <20170110073555.12178-1-andrew.smirnov@gmail.com> Precedence: list Cc: Mark Rutland <mark.rutland@arm.com>, devicetree@vger.kernel.org, andrew@lunn.ch, Andrey Smirnov <andrew.smirnov@gmail.com>, Vivien Didelot <vivien.didelot@savoirfairelinux.com>, Russell King <linux@armlinux.org.uk>, Stefan Agner <stefan@agner.ch>, linux-kernel@vger.kernel.org, Rob Herring <robh+dt@kernel.org>, Sascha Hauer <kernel@pengutronix.de>, Nikita Yushchenko <nikita.yoush@cogentembedded.com>, Shawn Guo <shawnguo@kernel.org>, cphealy@gmail.com MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: "linux-arm-kernel" <linux-arm-kernel-bounces@lists.infradead.org> Errors-To: linux-arm-kernel-bounces+patchwork-linux-arm=patchwork.kernel.org@lists.infradead.org

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 7327250..2f8ccb2 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -458,7 +458,8 @@ dtb-$(CONFIG_SOC_VF610) += \ vf610-cosmic.dtb \ vf610m4-cosmic.dtb \ vf610-twr.dtb \ - vf610-zii-dev-rev-b.dtb + vf610-zii-dev-rev-b.dtb \ + vf610-zii-dev-rev-c.dtb dtb-$(CONFIG_ARCH_MXS) += \ imx23-evk.dtb \ imx23-olinuxino.dtb \ diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts index c8e11a5..3887c4a 100644 --- a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts +++ b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts @@ -43,32 +43,12 @@ */ /dts-v1/; -#include "vf610.dtsi" +#include "vf610-zii-dev.dtsi" / { model = "ZII VF610 Development Board, Rev B"; compatible = "zii,vf610dev-b", "zii,vf610dev", "fsl,vf610"; - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory { - reg = <0x80000000 0x20000000>; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pinctrl_leds_debug>; - pinctrl-names = "default"; - - debug { - label = "zii:green:debug1"; - gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - }; - }; - mdio-mux { compatible = "mdio-mux-gpio"; pinctrl-0 = <&pinctrl_mdio_mux>; @@ -86,7 +66,7 @@ #address-cells = <1>; #size-cells = <0>; - switch0: switch0@0 { + switch0: switch@0 { compatible = "marvell,mv88e6085"; pinctrl-0 = <&pinctrl_gpio_switch0>; pinctrl-names = "default"; @@ -102,6 +82,7 @@ ports { #address-cells = <1>; #size-cells = <0>; + port@0 { reg = <0>; label = "lan0"; @@ -136,6 +117,7 @@ reg = <6>; label = "cpu"; ethernet = <&fec1>; + fixed-link { speed = <100>; full-duplex; @@ -169,7 +151,7 @@ #address-cells = <1>; #size-cells = <0>; - switch1: switch1@0 { + switch1: switch@0 { compatible = "marvell,mv88e6085"; pinctrl-0 = <&pinctrl_gpio_switch1>; pinctrl-names = "default"; @@ -185,6 +167,7 @@ ports { #address-cells = <1>; #size-cells = <0>; + port@0 { reg = <0>; label = "lan3"; @@ -208,6 +191,7 @@ label = "dsa"; link = <&switch2port9>; phy-mode = "rgmii-txid"; + fixed-link { speed = <1000>; full-duplex; @@ -228,16 +212,19 @@ mdio { #address-cells = <1>; #size-cells = <0>; + switch1phy0: switch1phy0@0 { reg = <0>; interrupt-parent = <&switch1>; interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; }; + switch1phy1: switch1phy0@1 { reg = <1>; interrupt-parent = <&switch1>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; }; + switch1phy2: switch1phy0@2 { reg = <2>; interrupt-parent = <&switch1>; @@ -262,6 +249,7 @@ ports { #address-cells = <1>; #size-cells = <0>; + port@0 { reg = <0>; label = "lan6"; @@ -280,6 +268,7 @@ port@3 { reg = <3>; label = "optical3"; + fixed-link { speed = <1000>; full-duplex; @@ -291,6 +280,7 @@ port@4 { reg = <4>; label = "optical4"; + fixed-link { speed = <1000>; full-duplex; @@ -305,6 +295,7 @@ phy-mode = "rgmii-txid"; link = <&switch1port5 &switch0port5>; + fixed-link { speed = <1000>; full-duplex; @@ -321,25 +312,6 @@ }; }; - reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu { - compatible = "regulator-fixed"; - regulator-name = "vcc_3v3_mcu"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - usb0_vbus: regulator-usb0-vbus { - compatible = "regulator-fixed"; - pinctrl-0 = <&pinctrl_usb_vbus>; - regulator-name = "usb_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 6 0>; - }; - spi0 { compatible = "spi-gpio"; pinctrl-0 = <&pinctrl_gpio_spi0>; @@ -376,49 +348,6 @@ }; }; -&adc0 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_adc0_ad5>; - vref-supply = <&reg_vcc_3v3_mcu>; - status = "okay"; -}; - -&edma0 { - status = "okay"; -}; - -&esdhc1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc1>; - bus-width = <4>; - status = "okay"; -}; - -&fec0 { - phy-mode = "rmii"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec0>; - status = "okay"; -}; - -&fec1 { - phy-mode = "rmii"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec1>; - status = "okay"; - - fixed-link { - speed = <100>; - full-duplex; - }; - - mdio1: mdio { - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - }; -}; - &i2c0 { clock-frequency = <100000>; pinctrl-names = "default"; @@ -443,33 +372,6 @@ interrupt-parent = <&gpio2>; interrupts = <2 IRQ_TYPE_LEVEL_LOW>; }; - - lm75@48 { - compatible = "national,lm75"; - reg = <0x48>; - }; - - at24c04@50 { - compatible = "atmel,24c04"; - reg = <0x50>; - }; - - at24c04@52 { - compatible = "atmel,24c04"; - reg = <0x52>; - }; - - ds1682@6b { - compatible = "dallas,ds1682"; - reg = <0x6b>; - }; -}; - -&i2c1 { - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1>; - status = "okay"; }; &i2c2 { @@ -539,120 +441,8 @@ }; }; -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart0>; - status = "okay"; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1>; - status = "okay"; -}; - -&uart2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; - status = "okay"; -}; - -&usbdev0 { - disable-over-current; - vbus-supply = <&usb0_vbus>; - dr_mode = "host"; - status = "okay"; -}; - -&usbh1 { - disable-over-current; - status = "okay"; -}; - -&usbmisc0 { - status = "okay"; -}; - -&usbmisc1 { - status = "okay"; -}; - -&usbphy0 { - status = "okay"; -}; - -&usbphy1 { - status = "okay"; -}; &iomuxc { - pinctrl_adc0_ad5: adc0ad5grp { - fsl,pins = < - VF610_PAD_PTC30__ADC0_SE5 0x00a1 - >; - }; - - pinctrl_dspi0: dspi0grp { - fsl,pins = < - VF610_PAD_PTB18__DSPI0_CS1 0x1182 - VF610_PAD_PTB19__DSPI0_CS0 0x1182 - VF610_PAD_PTB20__DSPI0_SIN 0x1181 - VF610_PAD_PTB21__DSPI0_SOUT 0x1182 - VF610_PAD_PTB22__DSPI0_SCK 0x1182 - >; - }; - - pinctrl_dspi2: dspi2grp { - fsl,pins = < - VF610_PAD_PTD31__DSPI2_CS1 0x1182 - VF610_PAD_PTD30__DSPI2_CS0 0x1182 - VF610_PAD_PTD29__DSPI2_SIN 0x1181 - VF610_PAD_PTD28__DSPI2_SOUT 0x1182 - VF610_PAD_PTD27__DSPI2_SCK 0x1182 - >; - }; - - pinctrl_esdhc1: esdhc1grp { - fsl,pins = < - VF610_PAD_PTA24__ESDHC1_CLK 0x31ef - VF610_PAD_PTA25__ESDHC1_CMD 0x31ef - VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef - VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef - VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef - VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef - VF610_PAD_PTA7__GPIO_134 0x219d - >; - }; - - pinctrl_fec0: fec0grp { - fsl,pins = < - VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d2 - VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d3 - VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1 - VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1 - VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1 - VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1 - VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2 - VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2 - VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2 - >; - }; - - pinctrl_fec1: fec1grp { - fsl,pins = < - VF610_PAD_PTA6__RMII_CLKIN 0x30d1 - VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2 - VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3 - VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1 - VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1 - VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1 - VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1 - VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2 - VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2 - VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2 - >; - }; - pinctrl_gpio_e6185_eeprom_sel: pinctrl-gpio-e6185-eeprom-spi0 { fsl,pins = < VF610_PAD_PTE27__GPIO_132 0x33e2 @@ -681,39 +471,6 @@ >; }; - pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset { - fsl,pins = < - VF610_PAD_PTE14__GPIO_119 0x31c2 - >; - }; - - pinctrl_i2c0: i2c0grp { - fsl,pins = < - VF610_PAD_PTB14__I2C0_SCL 0x37ff - VF610_PAD_PTB15__I2C0_SDA 0x37ff - >; - }; - - pinctrl_i2c1: i2c1grp { - fsl,pins = < - VF610_PAD_PTB16__I2C1_SCL 0x37ff - VF610_PAD_PTB17__I2C1_SDA 0x37ff - >; - }; - - pinctrl_i2c2: i2c2grp { - fsl,pins = < - VF610_PAD_PTA22__I2C2_SCL 0x37ff - VF610_PAD_PTA23__I2C2_SDA 0x37ff - >; - }; - - pinctrl_leds_debug: pinctrl-leds-debug { - fsl,pins = < - VF610_PAD_PTD20__GPIO_74 0x31c2 - >; - }; - pinctrl_mdio_mux: pinctrl-mdio-mux { fsl,pins = < VF610_PAD_PTA18__GPIO_8 0x31c2 @@ -728,48 +485,4 @@ VF610_PAD_PTB28__GPIO_98 0x219d >; }; - - pinctrl_qspi0: qspi0grp { - fsl,pins = < - VF610_PAD_PTD7__QSPI0_B_QSCK 0x31c3 - VF610_PAD_PTD8__QSPI0_B_CS0 0x31ff - VF610_PAD_PTD9__QSPI0_B_DATA3 0x31c3 - VF610_PAD_PTD10__QSPI0_B_DATA2 0x31c3 - VF610_PAD_PTD11__QSPI0_B_DATA1 0x31c3 - VF610_PAD_PTD12__QSPI0_B_DATA0 0x31c3 - >; - }; - - pinctrl_uart0: uart0grp { - fsl,pins = < - VF610_PAD_PTB10__UART0_TX 0x21a2 - VF610_PAD_PTB11__UART0_RX 0x21a1 - >; - }; - - pinctrl_uart1: uart1grp { - fsl,pins = < - VF610_PAD_PTB23__UART1_TX 0x21a2 - VF610_PAD_PTB24__UART1_RX 0x21a1 - >; - }; - - pinctrl_uart2: uart2grp { - fsl,pins = < - VF610_PAD_PTD0__UART2_TX 0x21a2 - VF610_PAD_PTD1__UART2_RX 0x21a1 - >; - }; - - pinctrl_usb_vbus: pinctrl-usb-vbus { - fsl,pins = < - VF610_PAD_PTA16__GPIO_6 0x31c2 - >; - }; - - pinctrl_usb0_host: usb0-host-grp { - fsl,pins = < - VF610_PAD_PTD6__GPIO_85 0x0062 - >; - }; }; diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts new file mode 100644 index 0000000..fbedb7b --- /dev/null +++ b/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts @@ -0,0 +1,414 @@ +/* + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations + * + * Based on an original 'vf610-twr.dts' which is Copyright 2015, + * Freescale Semiconductor, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "vf610-zii-dev.dtsi" + +/ { + model = "ZII VF610 Development Board, Rev C"; + compatible = "zii,vf610dev-c", "zii,vf610dev", "fsl,vf610"; + + mdio-mux { + compatible = "mdio-mux-gpio"; + pinctrl-0 = <&pinctrl_mdio_mux>; + pinctrl-names = "default"; + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH + &gpio0 9 GPIO_ACTIVE_HIGH + &gpio0 25 GPIO_ACTIVE_HIGH>; + mdio-parent-bus = <&mdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio_mux_1: mdio@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + switch0: switch@0 { + compatible = "marvell,mv88e6190"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&fec1>; + + fixed-link { + speed = <100>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + switch0port10: port@10 { + reg = <10>; + label = "dsa"; + phy-mode = "xgmii"; + link = <&switch1port10>; + }; + }; + }; + }; + + mdio_mux_2: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + switch1: switch@0 { + compatible = "marvell,mv88e6190"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + dsa,member = <0 1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan5"; + }; + + port@2 { + reg = <2>; + label = "lan6"; + }; + + port@3 { + reg = <3>; + label = "lan7"; + }; + + port@4 { + reg = <4>; + label = "lan8"; + }; + + + switch1port10: port@10 { + reg = <10>; + label = "dsa"; + phy-mode = "xgmii"; + link = <&switch0port10>; + }; + }; + }; + }; + + mdio_mux_4: mdio@4 { + reg = <4>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; + +&dspi0 { + bus-num = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi0>; + status = "okay"; + spi-num-chipselects = <2>; + + m25p128@0 { + compatible = "m25p128", "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <1000000>; + }; + + atzb-rf-233@1 { + compatible = "atmel,at86rf233"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctr_atzb_rf_233>; + + spi-max-frequency = <7500000>; + reg = <1>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gpio3>; + xtal-trim = /bits/ 8 <0x06>; + + sleep-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>; + reset-gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>; + + fsl,spi-cs-sck-delay = <180>; + fsl,spi-sck-cs-delay = <250>; + }; +}; + +&i2c0 { + /* + * U712 + * + * Exposed signals: + * P1 - WE2_CMD + * P2 - WE2_CLK + */ + gpio5: pca9557@18 { + compatible = "nxp,pca9557"; + reg = <0x18>; + gpio-controller; + #gpio-cells = <2>; + }; + + /* + * U121 + * + * Exposed signals: + * I/O0 - ENET_SWR_EN + * I/O1 - ESW1_RESETn + * I/O2 - ARINC_RESET + * I/O3 - DD1_IO_RESET + * I/O4 - ESW2_RESETn + * I/O5 - ESW3_RESETn + * I/O6 - ESW4_RESETn + * I/O8 - TP909 + * I/O9 - FEM_SEL + * I/O10 - WIFI_RESETn + * I/O11 - PHY_RSTn + * I/O12 - OPT1_SD + * I/O13 - OPT2_SD + * I/O14 - OPT1_TX_DIS + * I/O15 - OPT2_TX_DIS + */ + gpio6: sx1503@20 { + compatible = "semtech,sx1503q"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sx1503_20>; + #gpio-cells = <2>; + #interrupt-cells = <2>; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = <23 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + interrupt-controller; + + enet_swr_en { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "enet-swr-en"; + }; + }; + + /* + * U715 + * + * Exposed signals: + * IO0 - WE1_CLK + * IO1 - WE1_CMD + */ + gpio7: pca9554@22 { + compatible = "nxp,pca9554"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + + }; +}; + +&i2c1 { + at24mac602@00 { + compatible = "atmel,24c02"; + reg = <0x50>; + read-only; + }; +}; + +&i2c2 { + tca9548@70 { + compatible = "nxp,pca9548"; + pinctrl-0 = <&pinctrl_i2c_mux_reset>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + sfp2: at24c04@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + sfp3: at24c04@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&gpio0 { + eth0_intrp { + gpio-hog; + gpios = <23 GPIO_ACTIVE_HIGH>; + input; + line-name = "sx1503-irq"; + }; +}; + +&gpio3 { + eth0_intrp { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + input; + line-name = "eth0-intrp"; + }; +}; + +&fec0 { + mdio { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec0_phy_int>; + + interrupt-parent = <&gpio3>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + reg = <0>; + }; + }; +}; + +&iomuxc { + pinctr_atzb_rf_233: pinctrl-atzb-rf-233 { + fsl,pins = < + VF610_PAD_PTB2__GPIO_24 0x31c2 + VF610_PAD_PTE27__GPIO_132 0x33e2 + >; + }; + + + pinctrl_sx1503_20: pinctrl-sx1503-20 { + fsl,pins = < + VF610_PAD_PTB1__GPIO_23 0x219d + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + VF610_PAD_PTA20__UART3_TX 0x21a2 + VF610_PAD_PTA21__UART3_RX 0x21a1 + >; + }; + + pinctrl_mdio_mux: pinctrl-mdio-mux { + fsl,pins = < + VF610_PAD_PTA18__GPIO_8 0x31c2 + VF610_PAD_PTA19__GPIO_9 0x31c2 + VF610_PAD_PTB3__GPIO_25 0x31c2 + >; + }; + + pinctrl_fec0_phy_int: pinctrl-fec0-phy-int { + fsl,pins = < + VF610_PAD_PTB28__GPIO_98 0x219d + >; + }; +}; diff --git a/arch/arm/boot/dts/vf610-zii-dev.dtsi b/arch/arm/boot/dts/vf610-zii-dev.dtsi new file mode 100644 index 0000000..ca9e1bc --- /dev/null +++ b/arch/arm/boot/dts/vf610-zii-dev.dtsi @@ -0,0 +1,383 @@ +/* + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations + * + * Based on an original 'vf610-twr.dts' which is Copyright 2015, + * Freescale Semiconductor, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "vf610.dtsi" + +/ { + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x80000000 0x20000000>; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pinctrl_leds_debug>; + pinctrl-names = "default"; + + debug { + label = "zii:green:debug1"; + gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_mcu"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + usb0_vbus: regulator-usb0-vbus { + compatible = "regulator-fixed"; + pinctrl-0 = <&pinctrl_usb_vbus>; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 6 0>; + }; +}; + +&adc0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc0_ad5>; + vref-supply = <&reg_vcc_3v3_mcu>; + status = "okay"; +}; + +&edma0 { + status = "okay"; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1>; + bus-width = <4>; + status = "okay"; +}; + +&fec0 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec0>; + status = "okay"; +}; + +&fec1 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + status = "okay"; + + fixed-link { + speed = <100>; + full-duplex; + }; + + mdio1: mdio { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + }; +}; + +&i2c0 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c0>; + pinctrl-1 = <&pinctrl_i2c0_gpio>; + scl-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + status = "okay"; + + lm75@48 { + compatible = "national,lm75"; + reg = <0x48>; + }; + + at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + + at24c04@52 { + compatible = "atmel,24c04"; + reg = <0x52>; + }; + + ds1682@6b { + compatible = "dallas,ds1682"; + reg = <0x6b>; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbdev0 { + disable-over-current; + vbus-supply = <&usb0_vbus>; + dr_mode = "host"; + status = "okay"; +}; + +&usbh1 { + disable-over-current; + status = "okay"; +}; + +&usbmisc0 { + status = "okay"; +}; + +&usbmisc1 { + status = "okay"; +}; + +&usbphy0 { + status = "okay"; +}; + +&usbphy1 { + status = "okay"; +}; + +&iomuxc { + pinctrl_adc0_ad5: adc0ad5grp { + fsl,pins = < + VF610_PAD_PTC30__ADC0_SE5 0x00a1 + >; + }; + + pinctrl_dspi0: dspi0grp { + fsl,pins = < + VF610_PAD_PTB18__DSPI0_CS1 0x1182 + VF610_PAD_PTB19__DSPI0_CS0 0x1182 + VF610_PAD_PTB20__DSPI0_SIN 0x1181 + VF610_PAD_PTB21__DSPI0_SOUT 0x1182 + VF610_PAD_PTB22__DSPI0_SCK 0x1182 + >; + }; + + pinctrl_dspi2: dspi2grp { + fsl,pins = < + VF610_PAD_PTD31__DSPI2_CS1 0x1182 + VF610_PAD_PTD30__DSPI2_CS0 0x1182 + VF610_PAD_PTD29__DSPI2_SIN 0x1181 + VF610_PAD_PTD28__DSPI2_SOUT 0x1182 + VF610_PAD_PTD27__DSPI2_SCK 0x1182 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + VF610_PAD_PTA24__ESDHC1_CLK 0x31ef + VF610_PAD_PTA25__ESDHC1_CMD 0x31ef + VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef + VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef + VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef + VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef + VF610_PAD_PTA7__GPIO_134 0x219d + >; + }; + + pinctrl_fec0: fec0grp { + fsl,pins = < + VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d2 + VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d3 + VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1 + VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1 + VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1 + VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1 + VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2 + VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2 + VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + VF610_PAD_PTA6__RMII_CLKIN 0x30d1 + VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2 + VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3 + VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1 + VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1 + VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1 + VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1 + VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2 + VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2 + VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2 + >; + }; + + pinctrl_gpio_spi0: pinctrl-gpio-spi0 { + fsl,pins = < + VF610_PAD_PTB22__GPIO_44 0x33e2 + VF610_PAD_PTB21__GPIO_43 0x33e2 + VF610_PAD_PTB20__GPIO_42 0x33e1 + VF610_PAD_PTB19__GPIO_41 0x33e2 + VF610_PAD_PTB18__GPIO_40 0x33e2 + >; + }; + + pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset { + fsl,pins = < + VF610_PAD_PTE14__GPIO_119 0x31c2 + >; + }; + + pinctrl_i2c0: i2c0grp { + fsl,pins = < + VF610_PAD_PTB14__I2C0_SCL 0x37ff + VF610_PAD_PTB15__I2C0_SDA 0x37ff + >; + }; + + pinctrl_i2c0_gpio: i2c0grp-gpio { + fsl,pins = < + VF610_PAD_PTB14__GPIO_36 0x31c2 + VF610_PAD_PTB15__GPIO_37 0x31c2 + >; + }; + + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + VF610_PAD_PTB16__I2C1_SCL 0x37ff + VF610_PAD_PTB17__I2C1_SDA 0x37ff + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + VF610_PAD_PTA22__I2C2_SCL 0x37ff + VF610_PAD_PTA23__I2C2_SDA 0x37ff + >; + }; + + pinctrl_leds_debug: pinctrl-leds-debug { + fsl,pins = < + VF610_PAD_PTD20__GPIO_74 0x31c2 + >; + }; + + pinctrl_qspi0: qspi0grp { + fsl,pins = < + VF610_PAD_PTD7__QSPI0_B_QSCK 0x31c3 + VF610_PAD_PTD8__QSPI0_B_CS0 0x31ff + VF610_PAD_PTD9__QSPI0_B_DATA3 0x31c3 + VF610_PAD_PTD10__QSPI0_B_DATA2 0x31c3 + VF610_PAD_PTD11__QSPI0_B_DATA1 0x31c3 + VF610_PAD_PTD12__QSPI0_B_DATA0 0x31c3 + >; + }; + + pinctrl_uart0: uart0grp { + fsl,pins = < + VF610_PAD_PTB10__UART0_TX 0x21a2 + VF610_PAD_PTB11__UART0_RX 0x21a1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + VF610_PAD_PTB23__UART1_TX 0x21a2 + VF610_PAD_PTB24__UART1_RX 0x21a1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + VF610_PAD_PTD0__UART2_TX 0x21a2 + VF610_PAD_PTD1__UART2_RX 0x21a1 + >; + }; + + pinctrl_usb_vbus: pinctrl-usb-vbus { + fsl,pins = < + VF610_PAD_PTA16__GPIO_6 0x31c2 + >; + }; + + pinctrl_usb0_host: usb0-host-grp { + fsl,pins = < + VF610_PAD_PTD6__GPIO_85 0x0062 + >; + }; +};

[v6,2/2] ARM: dts: vf610-zii-dev: Add .dts file for rev. C

Commit Message

Patch