@@ -308,6 +308,7 @@
/* Per-port registers */
#define MVPP2_GMAC_CTRL_0_REG 0x0
#define MVPP2_GMAC_PORT_EN_MASK BIT(0)
+#define MVPP2_GMAC_PORT_TYPE_MASK BIT(1)
#define MVPP2_GMAC_MAX_RX_SIZE_OFFS 2
#define MVPP2_GMAC_MAX_RX_SIZE_MASK 0x7ffc
#define MVPP2_GMAC_MIB_CNTR_EN_MASK BIT(15)
@@ -319,16 +320,21 @@
#define MVPP2_GMAC_SA_LOW_OFFS 7
#define MVPP2_GMAC_CTRL_2_REG 0x8
#define MVPP2_GMAC_INBAND_AN_MASK BIT(0)
+#define MVPP2_GMAC_FLOW_CTRL_MASK GENMASK(2, 1)
#define MVPP2_GMAC_PCS_ENABLE_MASK BIT(3)
#define MVPP2_GMAC_PORT_RGMII_MASK BIT(4)
+#define MVPP2_GMAC_DISABLE_PADDING BIT(5)
#define MVPP2_GMAC_PORT_RESET_MASK BIT(6)
#define MVPP2_GMAC_AUTONEG_CONFIG 0xc
#define MVPP2_GMAC_FORCE_LINK_DOWN BIT(0)
#define MVPP2_GMAC_FORCE_LINK_PASS BIT(1)
+#define MVPP2_GMAC_IN_BAND_AUTONEG BIT(2)
+#define MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS BIT(3)
#define MVPP2_GMAC_CONFIG_MII_SPEED BIT(5)
#define MVPP2_GMAC_CONFIG_GMII_SPEED BIT(6)
#define MVPP2_GMAC_AN_SPEED_EN BIT(7)
#define MVPP2_GMAC_FC_ADV_EN BIT(9)
+#define MVPP2_GMAC_FLOW_CTRL_AUTONEG BIT(11)
#define MVPP2_GMAC_CONFIG_FULL_DUPLEX BIT(12)
#define MVPP2_GMAC_AN_DUPLEX_EN BIT(13)
#define MVPP2_GMAC_PORT_FIFO_CFG_1_REG 0x1c
@@ -4173,6 +4179,84 @@ static void mvpp2_interrupts_unmask(void *arg)
/* Port configuration routines */
+static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
+{
+ u32 val;
+
+ if (port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
+ val |= MVPP22_CTRL4_SYNC_BYPASS_DIS | MVPP22_CTRL4_DP_CLK_SEL |
+ MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
+ val &= ~MVPP22_CTRL4_EXT_PIN_GMII_SEL;
+ writel(val, port->base + MVPP22_GMAC_CTRL_4_REG);
+
+ val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
+ val |= MVPP2_GMAC_DISABLE_PADDING;
+ val &= ~MVPP2_GMAC_FLOW_CTRL_MASK;
+ writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
+ } else if (port->phy_interface == PHY_INTERFACE_MODE_RGMII) {
+ val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
+ val |= MVPP22_CTRL4_EXT_PIN_GMII_SEL |
+ MVPP22_CTRL4_SYNC_BYPASS_DIS |
+ MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
+ val &= ~MVPP22_CTRL4_DP_CLK_SEL;
+ writel(val, port->base + MVPP22_GMAC_CTRL_4_REG);
+
+ val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
+ val &= ~MVPP2_GMAC_DISABLE_PADDING;
+ writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
+ }
+
+ /* The port is connected to a copper PHY */
+ val = readl(port->base + MVPP2_GMAC_CTRL_0_REG);
+ val &= ~MVPP2_GMAC_PORT_TYPE_MASK;
+ writel(val, port->base + MVPP2_GMAC_CTRL_0_REG);
+
+ val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+ val |= MVPP2_GMAC_IN_BAND_AUTONEG |
+ MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS |
+ MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FLOW_CTRL_AUTONEG |
+ MVPP2_GMAC_AN_DUPLEX_EN;
+ writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+}
+
+static void mvpp2_port_mii_gmac_configure(struct mvpp2_port *port)
+{
+ u32 val;
+
+ /* Force link down */
+ val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+ val |= MVPP2_GMAC_FORCE_LINK_DOWN;
+ writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+
+ /* Set the GMAC in a reset state */
+ val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
+ val |= MVPP2_GMAC_PORT_RESET_MASK;
+ writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
+
+ /* Configure the PCS and in-band AN */
+ val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
+ if (port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ val |= MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK;
+ } else if (port->phy_interface == PHY_INTERFACE_MODE_RGMII) {
+ val |= MVPP2_GMAC_PORT_RGMII_MASK;
+ val &= ~MVPP2_GMAC_PCS_ENABLE_MASK;
+ }
+ writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
+
+ mvpp2_port_mii_gmac_configure_mode(port);
+
+ /* Unset the GMAC reset state */
+ val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
+ val &= ~MVPP2_GMAC_PORT_RESET_MASK;
+ writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
+
+ /* Stop forcing link down */
+ val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+ val &= ~MVPP2_GMAC_FORCE_LINK_DOWN;
+ writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+}
+
static void mvpp22_port_mii_set(struct mvpp2_port *port)
{
u32 val;
@@ -4190,38 +4274,16 @@ static void mvpp22_port_mii_set(struct mvpp2_port *port)
writel(val, port->base + MVPP22_XLG_CTRL3_REG);
}
-
- val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
- if (port->phy_interface == PHY_INTERFACE_MODE_RGMII)
- val |= MVPP22_CTRL4_EXT_PIN_GMII_SEL;
- else
- val &= ~MVPP22_CTRL4_EXT_PIN_GMII_SEL;
- val &= ~MVPP22_CTRL4_DP_CLK_SEL;
- val |= MVPP22_CTRL4_SYNC_BYPASS_DIS;
- val |= MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
- writel(val, port->base + MVPP22_GMAC_CTRL_4_REG);
}
static void mvpp2_port_mii_set(struct mvpp2_port *port)
{
- u32 val;
-
if (port->priv->hw_version == MVPP22)
mvpp22_port_mii_set(port);
- val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
-
- switch (port->phy_interface) {
- case PHY_INTERFACE_MODE_SGMII:
- val |= MVPP2_GMAC_INBAND_AN_MASK;
- break;
- case PHY_INTERFACE_MODE_RGMII:
- val |= MVPP2_GMAC_PORT_RGMII_MASK;
- default:
- val &= ~MVPP2_GMAC_PCS_ENABLE_MASK;
- }
-
- writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
+ if (port->phy_interface == PHY_INTERFACE_MODE_RGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII)
+ mvpp2_port_mii_gmac_configure(port);
}
static void mvpp2_port_fc_adv_enable(struct mvpp2_port *port)
This adds a routine to initialize the GMAC at the port level when using a port. This wasn't done until this commit, and the mvpp2 driver was relying on the bootloader/firmware initialization. This doesn't mean everything is configured in the mvpp2 driver now, but it helps reducing the gap. Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> --- drivers/net/ethernet/marvell/mvpp2.c | 112 +++++++++++++++++++++++++++-------- 1 file changed, 87 insertions(+), 25 deletions(-)