Message ID | 20170829084116.106695-3-liwei213@huawei.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On Tue, Aug 29, 2017 at 04:41:13PM +0800, Li Wei wrote: > add ufs node document for Hisilicon > > Signed-off-by: Li Wei <liwei213@huawei.com> > --- > Documentation/devicetree/bindings/ufs/ufs-hisi.txt | 35 ++++++++++++++++++++++ > 1 file changed, 35 insertions(+) > create mode 100644 Documentation/devicetree/bindings/ufs/ufs-hisi.txt > > diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt > new file mode 100644 > index 000000000000..cfc84c821d50 > --- /dev/null > +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt > @@ -0,0 +1,35 @@ > +* Hisilicon Universal Flash Storage (UFS) Host Controller > + > +UFS nodes are defined to describe on-chip UFS hardware macro. > +Each UFS Host Controller should have its own node. > + > +Required properties: > +- compatible : compatible list, contains one of the following - > + "hisilicon,hi3660-ufs" for hisi ufs host controller > + present on Hi3660 chipset. > +- reg : should contain UFS register address space & UFS SYS CTRL register address, > +- interrupt-parent : interrupt device > +- interrupts : interrupt number > +- clocks : List of phandle and clock specifier pairs > +- clock-names : List of clock input name strings sorted in the same > + order as the clocks property. "clk_ref", "clk_phy" is optional > + > +Optional properties for board device: > +- reset-gpio : specifies to reset devices reset-gpios Really, this is should be in a sub node representing the device. It's fine if this is it, but if we start adding power supplies and other properties it should be a separate node. > + > +Example: > + > + ufs: ufs@ff3b0000 { > + compatible = "jedec,ufs-1.1", "hisilicon,hi3660-ufs"; Need to reverse the order here. Most specific first. > + /* 0: HCI standard */ > + /* 1: UFS SYS CTRL */ > + reg = <0x0 0xff3b0000 0x0 0x1000>, > + <0x0 0xff3b1000 0x0 0x1000>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>, > + <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>; > + clock-names = "clk_ref", "clk_phy"; > + freq-table-hz = <0 0>, <0 0>; > + reset-gpio = <&gpio18 1 0>; > + } > -- > 2.11.0 >
Hi, Rob Thanks for your advises, I will fix them in the next patch. Thank you. -----邮件原件----- 发件人: Rob Herring [mailto:robh@kernel.org] 发送时间: 2017年9月1日 23:53 收件人: liwei (CM) 抄送: mark.rutland@arm.com; xuwei (O); catalin.marinas@arm.com; will.deacon@arm.com; vinholikatti@gmail.com; jejb@linux.vnet.ibm.com; martin.petersen@oracle.com; khilman@baylibre.com; arnd@arndb.de; gregory.clement@free-electrons.com; thomas.petazzoni@free-electrons.com; yamada.masahiro@socionext.com; riku.voipio@linaro.org; treding@nvidia.com; krzk@kernel.org; eric@anholt.net; devicetree@vger.kernel.org; linux-kernel@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux-scsi@vger.kernel.org; guodong.xu@linaro.org; Fengbaopeng (kevin, Kirin Solution Dept) 主题: Re: [PATCH v3 2/5] dt-bindings: scsi: ufs: add document for hisi-ufs On Tue, Aug 29, 2017 at 04:41:13PM +0800, Li Wei wrote: > add ufs node document for Hisilicon > > Signed-off-by: Li Wei <liwei213@huawei.com> > --- > Documentation/devicetree/bindings/ufs/ufs-hisi.txt | 35 > ++++++++++++++++++++++ > 1 file changed, 35 insertions(+) > create mode 100644 Documentation/devicetree/bindings/ufs/ufs-hisi.txt > > diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt > b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt > new file mode 100644 > index 000000000000..cfc84c821d50 > --- /dev/null > +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt > @@ -0,0 +1,35 @@ > +* Hisilicon Universal Flash Storage (UFS) Host Controller > + > +UFS nodes are defined to describe on-chip UFS hardware macro. > +Each UFS Host Controller should have its own node. > + > +Required properties: > +- compatible : compatible list, contains one of the following - > + "hisilicon,hi3660-ufs" for hisi ufs host controller > + present on Hi3660 chipset. > +- reg : should contain UFS register address space & UFS SYS CTRL register address, > +- interrupt-parent : interrupt device > +- interrupts : interrupt number > +- clocks : List of phandle and clock specifier pairs > +- clock-names : List of clock input name strings sorted in the same > + order as the clocks property. "clk_ref", "clk_phy" is > +optional > + > +Optional properties for board device: > +- reset-gpio : specifies to reset devices reset-gpios Really, this is should be in a sub node representing the device. It's fine if this is it, but if we start adding power supplies and other properties it should be a separate node. > + > +Example: > + > + ufs: ufs@ff3b0000 { > + compatible = "jedec,ufs-1.1", "hisilicon,hi3660-ufs"; Need to reverse the order here. Most specific first. > + /* 0: HCI standard */ > + /* 1: UFS SYS CTRL */ > + reg = <0x0 0xff3b0000 0x0 0x1000>, > + <0x0 0xff3b1000 0x0 0x1000>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>, > + <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>; > + clock-names = "clk_ref", "clk_phy"; > + freq-table-hz = <0 0>, <0 0>; > + reset-gpio = <&gpio18 1 0>; > + } > -- > 2.11.0 >
diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt new file mode 100644 index 000000000000..cfc84c821d50 --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt @@ -0,0 +1,35 @@ +* Hisilicon Universal Flash Storage (UFS) Host Controller + +UFS nodes are defined to describe on-chip UFS hardware macro. +Each UFS Host Controller should have its own node. + +Required properties: +- compatible : compatible list, contains one of the following - + "hisilicon,hi3660-ufs" for hisi ufs host controller + present on Hi3660 chipset. +- reg : should contain UFS register address space & UFS SYS CTRL register address, +- interrupt-parent : interrupt device +- interrupts : interrupt number +- clocks : List of phandle and clock specifier pairs +- clock-names : List of clock input name strings sorted in the same + order as the clocks property. "clk_ref", "clk_phy" is optional + +Optional properties for board device: +- reset-gpio : specifies to reset devices + +Example: + + ufs: ufs@ff3b0000 { + compatible = "jedec,ufs-1.1", "hisilicon,hi3660-ufs"; + /* 0: HCI standard */ + /* 1: UFS SYS CTRL */ + reg = <0x0 0xff3b0000 0x0 0x1000>, + <0x0 0xff3b1000 0x0 0x1000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>, + <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>; + clock-names = "clk_ref", "clk_phy"; + freq-table-hz = <0 0>, <0 0>; + reset-gpio = <&gpio18 1 0>; + }
add ufs node document for Hisilicon Signed-off-by: Li Wei <liwei213@huawei.com> --- Documentation/devicetree/bindings/ufs/ufs-hisi.txt | 35 ++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 Documentation/devicetree/bindings/ufs/ufs-hisi.txt