@@ -272,27 +272,35 @@
* Proper NAND usage will require DPR-76 to be in position 1-2, which disables
* MDIO signal of CP1.
*/
-&cps_nand {
- num-cs = <1>;
+&cps_nand_controller {
pinctrl-0 = <&nand_pins>, <&nand_rb>;
pinctrl-names = "default";
- nand-ecc-strength = <4>;
- nand-ecc-step-size = <512>;
- marvell,nand-enable-arbiter;
- marvell,system-controller = <&cps_syscon0>;
- nand-on-flash-bbt;
-
- partition@0 {
- label = "U-Boot";
- reg = <0 0x200000>;
- };
- partition@200000 {
- label = "Linux";
- reg = <0x200000 0xe00000>;
- };
- partition@1000000 {
- label = "Filesystem";
- reg = <0x1000000 0x3f000000>;
+
+ nand@0 {
+ reg = <0>;
+ marvell,rb = <0>;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0 0x200000>;
+ };
+ partition@200000 {
+ label = "Linux";
+ reg = <0x200000 0xe00000>;
+ };
+ partition@1000000 {
+ label = "Filesystem";
+ reg = <0x1000000 0x3f000000>;
+ };
+ };
};
};
@@ -310,20 +310,20 @@
status = "disabled";
};
- cps_nand: nand@720000 {
+ cps_nand_controller: nand@720000 {
/*
* Due to the limiation of the pin available
* this controller is only usable on the CPM
* for A7K and on the CPS for A8K.
*/
- compatible = "marvell,armada370-nand",
- "marvell,armada-8k-nand";
+ compatible = "marvell,armada-8k-nand-controller",
+ "marvell,armada370-nand-controller";
reg = <0x720000 0x54>;
#address-cells = <1>;
- #size-cells = <1>;
+ #size-cells = <0>;
interrupts = <ICU_GRP_NSR 115 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cps_clk 1 2>;
- marvell,system-controller = <&cpm_syscon0>;
+ marvell,system-controller = <&cps_syscon0>;
status = "disabled";
};
Use the new bindings of the reworked Marvell NAND controller driver. Also adapt the nand controller node organization to distinguish which property is relevant for the controller, and which one is NAND chip specific. Expose the partitions as a subnode of the NAND chip. Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as the driver activates the arbiter by default for all boards (either needed or harmless). Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> --- arch/arm64/boot/dts/marvell/armada-8040-db.dts | 46 +++++++++++++--------- .../arm64/boot/dts/marvell/armada-cp110-slave.dtsi | 10 ++--- 2 files changed, 32 insertions(+), 24 deletions(-)