diff mbox

[v2,18/19] ARM: dts: aspeed-romulus: Update Romulus system

Message ID 20171215062443.23059-19-joel@jms.id.au (mailing list archive)
State New, archived
Headers show

Commit Message

Joel Stanley Dec. 15, 2017, 6:24 a.m. UTC
- Fix incorrect RAM size
 - Remove alias; these are now specified in the dtsi
 - Add newly upstreamed devices
 - Include OpenBMC flash layout

Signed-off-by: Joel Stanley <joel@jms.id.au>
---
 arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts | 153 ++++++++++++++++++++++++++-
 1 file changed, 148 insertions(+), 5 deletions(-)

Comments

Cédric Le Goater Dec. 18, 2017, 9:32 a.m. UTC | #1
Some comments below,

On 12/15/2017 07:24 AM, Joel Stanley wrote:
>  - Fix incorrect RAM size
>  - Remove alias; these are now specified in the dtsi
>  - Add newly upstreamed devices
>  - Include OpenBMC flash layout
> 
> Signed-off-by: Joel Stanley <joel@jms.id.au>
> ---
>  arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts | 153 ++++++++++++++++++++++++++-
>  1 file changed, 148 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
> index a7a9386f964d..bfdf643584df 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
> @@ -7,17 +7,13 @@
>  	model = "Romulus BMC";
>  	compatible = "ibm,romulus-bmc", "aspeed,ast2500";
>  
> -	aliases {
> -		serial4 = &uart5;
> -	};
> -
>  	chosen {
>  		stdout-path = &uart5;
>  		bootargs = "console=ttyS4,115200 earlyprintk";
>  	};
>  
>  	memory {
> -		reg = <0x80000000 0x40000000>;
> +		reg = <0x80000000 0x20000000>;
>  	};
>  
>  	reserved-memory {
> @@ -29,6 +25,73 @@
>  			no-map;
>  			reg = <0xbf000000 0x01000000>; /* 16M */
>  		};
> +
> +		flash_memory: region@98000000 {
> +			no-map;
> +			reg = <0x98000000 0x04000000>; /* 64M */
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		fault {
> +			gpios = <&gpio ASPEED_GPIO(N, 2) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		identify {
> +			gpios = <&gpio ASPEED_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		power {
> +			gpios = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	fsi: gpio-fsi {
> +		compatible = "fsi-master-gpio", "fsi-master";
> +		#address-cells = <2>;
> +		#size-cells = <0>;
> +
> +		clock-gpios = <&gpio ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
> +		data-gpios = <&gpio ASPEED_GPIO(AA, 2) GPIO_ACTIVE_HIGH>;
> +		mux-gpios = <&gpio ASPEED_GPIO(A, 6) GPIO_ACTIVE_HIGH>;
> +		enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
> +		trans-gpios = <&gpio ASPEED_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		checkstop {
> +			label = "checkstop";
> +			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
> +			linux,code = <ASPEED_GPIO(J, 2)>;
> +		};
> +	};
> +};
> +
> +&fmc {
> +	status = "okay";
> +
> +	flash@0 {
> +		status = "okay";
> +		label = "pnor";
> +		m25p,fast-read;
> +#include "openbmc-flash-layout.dtsi"
> +	};
> +};
> +
> +&spi1 {
> +	status = "okay";
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_spi1_default>;
> +
> +	flash@0 {
> +		status = "okay";
> +		label = "pnor";
> +		m25p,fast-read;
>  	};
>  };


hmm, the fmc and spi1 bindings were already added in commit 1142aea9ff9d.


> @@ -38,6 +101,7 @@
>  		status = "okay";
>  		m25p,fast-read;
>  		label = "bmc";
> +#include "openbmc-flash-layout.dtsi"


This looks like an extra "fmc" node ? 

>  	};
>  };
>  
> @@ -53,6 +117,12 @@
>  	};
>  };
>  
> +&lpc_ctrl {
> +	status = "okay";
> +	memory-region = <&flash_memory>;
> +	flash = <&spi1>;
> +};
> +
>  &uart1 {
>  	/* Rear RS-232 connector */
>  	status = "okay";
> @@ -81,6 +151,10 @@
>  	pinctrl-0 = <&pinctrl_rmii1_default>;
>  };
>  
> +&i2c1 {
> +	status = "okay";
> +};
> +
>  &i2c2 {
>  	status = "okay";
>  };
> @@ -133,8 +207,77 @@
>  
>  &i2c12 {
>  	status = "okay";
> +
> +	max31785@52 {
> +		compatible = "maxim,max31785";
> +		reg = <0x52>;
> +	};
> +};
> +
> +&gpio {
> +	nic_func_mode0 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
> +		output-low;
> +		line-name = "nic_func_mode0";
> +	};
> +	nic_func_mode1 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
> +		output-low;
> +		line-name = "nic_func_mode1";
> +	};
>  };
>  
>  &vuart {
>  	status = "okay";
>  };
> +
> +&gfx {
> +	status = "okay";
> +};
> +
> +&pinctrl {
> +	aspeed,external-nodes = <&gfx &lhc>;
> +};
> +
> +&pwm_tacho {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>;
> +
> +	fan@0 {
> +		reg = <0x00>;
> +		aspeed,fan-tach-ch = /bits/ 8 <0x08>;
> +	};
> +
> +	fan@1 {
> +		reg = <0x00>;
> +		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
> +	};
> +
> +	fan@2 {
> +		reg = <0x01>;
> +		aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
> +	};
> +
> +	fan@3 {
> +		reg = <0x01>;
> +		aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
> +	};
> +
> +	fan@4 {
> +		reg = <0x00>;
> +		aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
> +	};
> +
> +	fan@5 {
> +		reg = <0x00>;
> +		aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
> +	};
> +
> +	fan@6 {
> +		reg = <0x01>;
> +		aspeed,fan-tach-ch = /bits/ 8 <0x0e>;
> +	};
> +};
>
Joel Stanley Dec. 20, 2017, 3:22 a.m. UTC | #2
On Mon, Dec 18, 2017 at 8:02 PM, Cédric Le Goater <clg@kaod.org> wrote:
>> +};
>> +
>> +&fmc {
>> +     status = "okay";
>> +
>> +     flash@0 {
>> +             status = "okay";
>> +             label = "pnor";
>> +             m25p,fast-read;
>> +#include "openbmc-flash-layout.dtsi"
>> +     };
>> +};
>> +
>> +&spi1 {
>> +     status = "okay";
>> +
>> +     pinctrl-names = "default";
>> +     pinctrl-0 = <&pinctrl_spi1_default>;
>> +
>> +     flash@0 {
>> +             status = "okay";
>> +             label = "pnor";
>> +             m25p,fast-read;
>>       };
>>  };
>
>
> hmm, the fmc and spi1 bindings were already added in commit 1142aea9ff9d.
>
>
>> @@ -38,6 +101,7 @@
>>               status = "okay";
>>               m25p,fast-read;
>>               label = "bmc";
>> +#include "openbmc-flash-layout.dtsi"
>
>
> This looks like an extra "fmc" node ?

You're right. It still built and booted too. Good catch.

Cheers,

Joel
diff mbox

Patch

diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
index a7a9386f964d..bfdf643584df 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
@@ -7,17 +7,13 @@ 
 	model = "Romulus BMC";
 	compatible = "ibm,romulus-bmc", "aspeed,ast2500";
 
-	aliases {
-		serial4 = &uart5;
-	};
-
 	chosen {
 		stdout-path = &uart5;
 		bootargs = "console=ttyS4,115200 earlyprintk";
 	};
 
 	memory {
-		reg = <0x80000000 0x40000000>;
+		reg = <0x80000000 0x20000000>;
 	};
 
 	reserved-memory {
@@ -29,6 +25,73 @@ 
 			no-map;
 			reg = <0xbf000000 0x01000000>; /* 16M */
 		};
+
+		flash_memory: region@98000000 {
+			no-map;
+			reg = <0x98000000 0x04000000>; /* 64M */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		fault {
+			gpios = <&gpio ASPEED_GPIO(N, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		identify {
+			gpios = <&gpio ASPEED_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
+		};
+
+		power {
+			gpios = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	fsi: gpio-fsi {
+		compatible = "fsi-master-gpio", "fsi-master";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		clock-gpios = <&gpio ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
+		data-gpios = <&gpio ASPEED_GPIO(AA, 2) GPIO_ACTIVE_HIGH>;
+		mux-gpios = <&gpio ASPEED_GPIO(A, 6) GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
+		trans-gpios = <&gpio ASPEED_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		checkstop {
+			label = "checkstop";
+			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(J, 2)>;
+		};
+	};
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		label = "pnor";
+		m25p,fast-read;
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		label = "pnor";
+		m25p,fast-read;
 	};
 };
 
@@ -38,6 +101,7 @@ 
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc";
+#include "openbmc-flash-layout.dtsi"
 	};
 };
 
@@ -53,6 +117,12 @@ 
 	};
 };
 
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+	flash = <&spi1>;
+};
+
 &uart1 {
 	/* Rear RS-232 connector */
 	status = "okay";
@@ -81,6 +151,10 @@ 
 	pinctrl-0 = <&pinctrl_rmii1_default>;
 };
 
+&i2c1 {
+	status = "okay";
+};
+
 &i2c2 {
 	status = "okay";
 };
@@ -133,8 +207,77 @@ 
 
 &i2c12 {
 	status = "okay";
+
+	max31785@52 {
+		compatible = "maxim,max31785";
+		reg = <0x52>;
+	};
+};
+
+&gpio {
+	nic_func_mode0 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "nic_func_mode0";
+	};
+	nic_func_mode1 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "nic_func_mode1";
+	};
 };
 
 &vuart {
 	status = "okay";
 };
+
+&gfx {
+	status = "okay";
+};
+
+&pinctrl {
+	aspeed,external-nodes = <&gfx &lhc>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x08>;
+	};
+
+	fan@1 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
+	};
+
+	fan@2 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
+	};
+
+	fan@3 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+	};
+
+	fan@4 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
+	};
+
+	fan@5 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
+	};
+
+	fan@6 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0e>;
+	};
+};