@@ -6,6 +6,9 @@ struct dev_archdata {
#if defined(CONFIG_INTEL_IOMMU) || defined(CONFIG_AMD_IOMMU)
void *iommu; /* hook for IOMMU specific extension */
#endif
+#ifdef CONFIG_STA2X11
+ bool is_sta2x11 : 1;
+#endif
};
#if defined(CONFIG_X86_DEV_DMA_OPS) && defined(CONFIG_PCI_DOMAINS)
@@ -159,43 +159,6 @@ static dma_addr_t a2p(dma_addr_t a, struct pci_dev *pdev)
return p;
}
-/**
- * sta2x11_swiotlb_alloc_coherent - Allocate swiotlb bounce buffers
- * returns virtual address. This is the only "special" function here.
- * @dev: PCI device
- * @size: Size of the buffer
- * @dma_handle: DMA address
- * @flags: memory flags
- */
-static void *sta2x11_swiotlb_alloc_coherent(struct device *dev,
- size_t size,
- dma_addr_t *dma_handle,
- gfp_t flags,
- unsigned long attrs)
-{
- void *vaddr;
-
- vaddr = swiotlb_alloc(dev, size, dma_handle, flags, attrs);
- *dma_handle = p2a(*dma_handle, to_pci_dev(dev));
- return vaddr;
-}
-
-/* We have our own dma_ops: the same as swiotlb but from alloc (above) */
-static const struct dma_map_ops sta2x11_dma_ops = {
- .alloc = sta2x11_swiotlb_alloc_coherent,
- .free = swiotlb_free,
- .map_page = swiotlb_map_page,
- .unmap_page = swiotlb_unmap_page,
- .map_sg = swiotlb_map_sg_attrs,
- .unmap_sg = swiotlb_unmap_sg_attrs,
- .sync_single_for_cpu = swiotlb_sync_single_for_cpu,
- .sync_single_for_device = swiotlb_sync_single_for_device,
- .sync_sg_for_cpu = swiotlb_sync_sg_for_cpu,
- .sync_sg_for_device = swiotlb_sync_sg_for_device,
- .mapping_error = swiotlb_dma_mapping_error,
- .dma_supported = dma_direct_supported,
-};
-
/* At setup time, we use our own ops if the device is a ConneXt one */
static void sta2x11_setup_pdev(struct pci_dev *pdev)
{
@@ -205,7 +168,8 @@ static void sta2x11_setup_pdev(struct pci_dev *pdev)
return;
pci_set_consistent_dma_mask(pdev, STA2X11_AMBA_SIZE - 1);
pci_set_dma_mask(pdev, STA2X11_AMBA_SIZE - 1);
- pdev->dev.dma_ops = &sta2x11_dma_ops;
+ pdev->dev.dma_ops = &swiotlb_dma_ops;
+ pdev->dev.archdata.is_sta2x11 = true;
/* We must enable all devices as master, for audio DMA to work */
pci_set_master(pdev);
@@ -225,7 +189,7 @@ bool dma_capable(struct device *dev, dma_addr_t addr, size_t size)
{
struct sta2x11_mapping *map;
- if (dev->dma_ops != &sta2x11_dma_ops) {
+ if (!dev->archdata.is_sta2x11) {
if (!dev->dma_mask)
return false;
return addr + size - 1 <= *dev->dma_mask;
@@ -249,7 +213,7 @@ bool dma_capable(struct device *dev, dma_addr_t addr, size_t size)
*/
dma_addr_t __phys_to_dma(struct device *dev, phys_addr_t paddr)
{
- if (dev->dma_ops != &sta2x11_dma_ops)
+ if (!dev->archdata.is_sta2x11)
return paddr;
return p2a(paddr, to_pci_dev(dev));
}
@@ -261,7 +225,7 @@ dma_addr_t __phys_to_dma(struct device *dev, phys_addr_t paddr)
*/
phys_addr_t __dma_to_phys(struct device *dev, dma_addr_t daddr)
{
- if (dev->dma_ops != &sta2x11_dma_ops)
+ if (!dev->archdata.is_sta2x11)
return daddr;
return a2p(daddr, to_pci_dev(dev));
}
Both the swiotlb and the dma-direct code already call into phys_to_dma to translate the DMA address. So the sta2x11 into phys_to_dma and dma_to_phys are enough to handle this "special" device, and we can use the plain old swiotlb ops. Signed-off-by: Christoph Hellwig <hch@lst.de> --- arch/x86/include/asm/device.h | 3 +++ arch/x86/pci/sta2x11-fixup.c | 46 +++++-------------------------------------- 2 files changed, 8 insertions(+), 41 deletions(-)