@@ -4501,6 +4501,7 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
mvpp22_gop_init_rgmii(port);
break;
case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_1000BASEX:
mvpp22_gop_init_sgmii(port);
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -4538,7 +4539,8 @@ static void mvpp22_gop_unmask_irq(struct mvpp2_port *port)
u32 val;
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
/* Enable the GMAC link status irq for this port */
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val |= MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
@@ -4568,7 +4570,8 @@ static void mvpp22_gop_mask_irq(struct mvpp2_port *port)
}
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val &= ~MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_SUM_MASK);
@@ -4580,7 +4583,8 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
u32 val;
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_MASK);
val |= MVPP22_GMAC_INT_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_MASK);
@@ -4605,6 +4609,7 @@ static int mvpp22_comphy_init(struct mvpp2_port *port)
switch (port->phy_interface) {
case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_1000BASEX:
mode = PHY_MODE_SGMII;
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -4625,7 +4630,8 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
{
u32 val;
- if (port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
val |= MVPP22_CTRL4_SYNC_BYPASS_DIS | MVPP22_CTRL4_DP_CLK_SEL |
MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
@@ -4640,9 +4646,11 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
writel(val, port->base + MVPP22_GMAC_CTRL_4_REG);
}
- /* The port is connected to a copper PHY */
val = readl(port->base + MVPP2_GMAC_CTRL_0_REG);
- val &= ~MVPP2_GMAC_PORT_TYPE_MASK;
+ if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ val |= MVPP2_GMAC_PORT_TYPE_MASK;
+ else
+ val &= ~MVPP2_GMAC_PORT_TYPE_MASK;
writel(val, port->base + MVPP2_GMAC_CTRL_0_REG);
val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
@@ -4651,6 +4659,19 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
MVPP2_GMAC_AN_DUPLEX_EN;
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII)
val |= MVPP2_GMAC_IN_BAND_AUTONEG;
+
+ if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ /* 1000BaseX port cannot negotiate speed nor can it
+ * negotiate duplex: they are always operating with a
+ * fixed speed of 1000Mbps in full duplex, so force
+ * 1000 speed and full duplex here.
+ */
+ val |= MVPP2_GMAC_CONFIG_GMII_SPEED |
+ MVPP2_GMAC_CONFIG_FULL_DUPLEX;
+ else
+ val |= MVPP2_GMAC_AN_SPEED_EN |
+ MVPP2_GMAC_AN_DUPLEX_EN;
+
writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
}
@@ -4671,7 +4692,8 @@ static void mvpp2_port_mii_gmac_configure(struct mvpp2_port *port)
/* Configure the PCS and in-band AN */
val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
- if (port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val |= MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK;
} else if (phy_interface_mode_is_rgmii(port->phy_interface)) {
val &= ~MVPP2_GMAC_PCS_ENABLE_MASK;
@@ -4733,7 +4755,8 @@ static void mvpp2_port_mii_set(struct mvpp2_port *port)
mvpp22_port_mii_set(port);
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII)
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
mvpp2_port_mii_gmac_configure(port);
else if (port->phy_interface == PHY_INTERFACE_MODE_10GKR)
mvpp2_port_mii_xlg_configure(port);
@@ -4810,7 +4833,8 @@ static void mvpp2_port_loopback_set(struct mvpp2_port *port)
else
val &= ~MVPP2_GMAC_GMII_LB_EN_MASK;
- if (port->phy_interface == PHY_INTERFACE_MODE_SGMII)
+ if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
val |= MVPP2_GMAC_PCS_LB_EN_MASK;
else
val &= ~MVPP2_GMAC_PCS_LB_EN_MASK;
@@ -6023,7 +6047,8 @@ static irqreturn_t mvpp2_link_status_isr(int irq, void *dev_id)
link = true;
}
} else if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_STAT);
if (val & MVPP22_GMAC_INT_STAT_LINK) {
event = true;
This patch adds the 1000Base-X PHY mode support in the Marvell PPv2 driver. 1000Base-X is quite close the SGMII and uses nearly the same code path. Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> --- drivers/net/ethernet/marvell/mvpp2.c | 45 ++++++++++++++++++++++++++++-------- 1 file changed, 35 insertions(+), 10 deletions(-)