diff mbox

[v2] pinctrl: msm: fix gpio-hog related boot issues

Message ID 20180402121005.10080-1-chunkeey@gmail.com (mailing list archive)
State New, archived
Headers show

Commit Message

Christian Lamparter April 2, 2018, 12:10 p.m. UTC
Sven Eckelmann reported an issue with the current IPQ4019 pinctrl.
Setting up any gpio-hog in the device-tree for his device would
"kill the bootup completely":

| [    0.477838] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [    0.499828] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferring probe
| [    1.298883] requesting hog GPIO enable USB2 power (chip 1000000.pinctrl, offset 58) failed, -517
| [    1.299609] gpiochip_add_data: GPIOs 0..99 (1000000.pinctrl) failed to register
| [    1.308589] ipq4019-pinctrl 1000000.pinctrl: Failed register gpiochip
| [    1.316586] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [    1.322415] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferri

This was also verified on a RT-AC58U (IPQ4018) which would
no longer boot, if a gpio-hog was specified. (Tried forcing
the USB LED PIN (GPIO0) to high.).

The problem is that Pinctrl+GPIO registration is currently
peformed in the following order in pinctrl-msm.c:
	1. pinctrl_register()
	2. gpiochip_add()
	3. gpiochip_add_pin_range()

The actual error code -517 == -EPROBE_DEFER is coming from
pinctrl_get_device_gpio_range(), which is called through:
        gpiochip_add
            of_gpiochip_add
                of_gpiochip_scan_gpios
                    gpiod_hog
                        gpiochip_request_own_desc
                            __gpiod_request
                                chip->request
                                    gpiochip_generic_request
                                       pinctrl_gpio_request
                                          pinctrl_get_device_gpio_range

pinctrl_get_device_gpio_range() is unable to find any valid
pin ranges, since nothing has been added to the pinctrldev_list yet.
so the range can't be found, and the operation fails with -EPROBE_DEFER.

This patch fixes the issue by adding the "gpio-ranges" property
to the pinctrl device node of all upstream Qcom SoC, so the
ranges are added by of_gpiochip_add_pin_range(), which is
called by of_gpiochip_add() before the call to
of_gpiochip_scan_gpios() happens.gpiochip_add_pin_range() is longer
needed and removed (to prevent adding the same entry to the
pinctrldev_list twice).

Cc: stable@vger.kernel.org
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
---
The msm8998 would need something like
	gpio-ranges = <&tlmm 0 0 150>;

v1->v2: restore gpiochip_add_pin_range() for ACPI compatibility
---
 arch/arm/boot/dts/qcom-apq8064.dtsi   |  1 +
 arch/arm/boot/dts/qcom-apq8084.dtsi   |  1 +
 arch/arm/boot/dts/qcom-ipq4019.dtsi   |  1 +
 arch/arm/boot/dts/qcom-ipq8064.dtsi   |  1 +
 arch/arm/boot/dts/qcom-mdm9615.dtsi   |  1 +
 arch/arm/boot/dts/qcom-msm8660.dtsi   |  1 +
 arch/arm/boot/dts/qcom-msm8960.dtsi   |  1 +
 arch/arm/boot/dts/qcom-msm8974.dtsi   |  1 +
 arch/arm64/boot/dts/qcom/ipq8074.dtsi |  3 ++-
 arch/arm64/boot/dts/qcom/msm8916.dtsi |  1 +
 arch/arm64/boot/dts/qcom/msm8992.dtsi |  1 +
 arch/arm64/boot/dts/qcom/msm8994.dtsi |  1 +
 arch/arm64/boot/dts/qcom/msm8996.dtsi |  1 +
 drivers/pinctrl/qcom/pinctrl-msm.c    | 21 ++++++++++++++++-----
 14 files changed, 30 insertions(+), 6 deletions(-)

Comments

Bjorn Andersson April 2, 2018, 3:04 p.m. UTC | #1
On Mon 02 Apr 05:10 PDT 2018, Christian Lamparter wrote:

[..]
> diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> index 0a6f7952bbb1..18511e782cbd 100644
> --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> @@ -530,6 +530,7 @@
>  			reg = <0x01010000 0x300000>;
>  			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>  			gpio-controller;
> +			gpio-ranges = <&msmgpio 0 0 150>;
>  			#gpio-cells = <2>;
>  			interrupt-controller;
>  			#interrupt-cells = <2>;
> diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
> index 495432f3341b..258fa357d946 100644
> --- a/drivers/pinctrl/qcom/pinctrl-msm.c
> +++ b/drivers/pinctrl/qcom/pinctrl-msm.c
> @@ -831,11 +831,22 @@ static int msm_gpio_init(struct msm_pinctrl *pctrl)
>  		return ret;
>  	}
>  
> -	ret = gpiochip_add_pin_range(&pctrl->chip, dev_name(pctrl->dev), 0, 0, chip->ngpio);
> -	if (ret) {
> -		dev_err(pctrl->dev, "Failed to add pin range\n");
> -		gpiochip_remove(&pctrl->chip);
> -		return ret;
> +	if (!is_of_node(pctrl->dev->fwnode)) {

Afaict this still means that if I boot this kernel with yesterday's dtb
(without gpio-ranges) I will not get any gpios. This isn't okay. 

@Linus, I count 24 callers of gpiochip_add_pin_range(). Is this
suggestion reasonable?

Can we make gpiochip_add_pin_range() check if there's already a
gpio-range and return ok in some way?

> +		/*
> +		 * gpiochip_add_pin_range() is meant for platforms that
> +		 * don't support DT. All DT platforms should just add
> +		 * the gpio-ranges property to the pinctrl device node.
> +		 *
> +		 * See Documentation/devicetree/bindings/gpio/gpio.txt .
> +		 */
> +		ret = gpiochip_add_pin_range(&pctrl->chip,
> +			dev_name(pctrl->dev), 0, 0, chip->ngpio);
> +
> +		if (ret) {
> +			dev_err(pctrl->dev, "Failed to add pin range\n");
> +			gpiochip_remove(&pctrl->chip);
> +			return ret;
> +		}

Regards,
Bjorn
diff mbox

Patch

diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 3ca96e361878..17ad9cbd9f8c 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -327,6 +327,7 @@ 
 			reg = <0x800000 0x4000>;
 
 			gpio-controller;
+			gpio-ranges = <&tlmm_pinmux 0 0 90>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index 0e1e98707e3f..d9481d083802 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -396,6 +396,7 @@ 
 			compatible = "qcom,apq8084-pinctrl";
 			reg = <0xfd510000 0x4000>;
 			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 147>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index c1e65aaf3cad..d85b15774c64 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -147,6 +147,7 @@ 
 			compatible = "qcom,ipq4019-pinctrl";
 			reg = <0x01000000 0x300000>;
 			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 100>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
index 1e0a3b446f7a..26eab9a68d90 100644
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -108,6 +108,7 @@ 
 			reg = <0x800000 0x4000>;
 
 			gpio-controller;
+			gpio-ranges = <&qcom_pinmux 0 0 69>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom-mdm9615.dtsi
index c852b69229c9..cfdaca5f259a 100644
--- a/arch/arm/boot/dts/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom-mdm9615.dtsi
@@ -128,6 +128,7 @@ 
 		msmgpio: pinctrl@800000 {
 			compatible = "qcom,mdm9615-pinctrl";
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 88>;
 			#gpio-cells = <2>;
 			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index 33030f9419fe..47cf9c4ca062 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -110,6 +110,7 @@ 
 			reg = <0x800000 0x4000>;
 
 			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 173>;
 			#gpio-cells = <2>;
 			interrupts = <0 16 0x4>;
 			interrupt-controller;
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index 1733d8f40ab1..f6d8b1af5a8a 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -102,6 +102,7 @@ 
 		msmgpio: pinctrl@800000 {
 			compatible = "qcom,msm8960-pinctrl";
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 152>;
 			#gpio-cells = <2>;
 			interrupts = <0 16 0x4>;
 			interrupt-controller;
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index d9019a49b292..1250e071a6e2 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -696,6 +696,7 @@ 
 			compatible = "qcom,msm8974-pinctrl";
 			reg = <0xfd510000 0x4000>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 146>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 2bc5dec5614d..d2c36b467466 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -24,11 +24,12 @@ 
 		ranges = <0 0 0 0xffffffff>;
 		compatible = "simple-bus";
 
-		pinctrl@1000000 {
+		tlmm: pinctrl@1000000 {
 			compatible = "qcom,ipq8074-pinctrl";
 			reg = <0x1000000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 70>;
 			#gpio-cells = <0x2>;
 			interrupt-controller;
 			#interrupt-cells = <0x2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index e51b04900726..e06cb90c8ec3 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -281,6 +281,7 @@ 
 			reg = <0x1000000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 122>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi
index 171578747ed0..173b6bc60816 100644
--- a/arch/arm64/boot/dts/qcom/msm8992.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi
@@ -179,6 +179,7 @@ 
 			reg = <0xfd510000 0x4000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 146>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index f33c41d01c86..68705db4696b 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -141,6 +141,7 @@ 
 			reg = <0xfd510000 0x4000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 146>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 0a6f7952bbb1..18511e782cbd 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -530,6 +530,7 @@ 
 			reg = <0x01010000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 150>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index 495432f3341b..258fa357d946 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -831,11 +831,22 @@  static int msm_gpio_init(struct msm_pinctrl *pctrl)
 		return ret;
 	}
 
-	ret = gpiochip_add_pin_range(&pctrl->chip, dev_name(pctrl->dev), 0, 0, chip->ngpio);
-	if (ret) {
-		dev_err(pctrl->dev, "Failed to add pin range\n");
-		gpiochip_remove(&pctrl->chip);
-		return ret;
+	if (!is_of_node(pctrl->dev->fwnode)) {
+		/*
+		 * gpiochip_add_pin_range() is meant for platforms that
+		 * don't support DT. All DT platforms should just add
+		 * the gpio-ranges property to the pinctrl device node.
+		 *
+		 * See Documentation/devicetree/bindings/gpio/gpio.txt .
+		 */
+		ret = gpiochip_add_pin_range(&pctrl->chip,
+			dev_name(pctrl->dev), 0, 0, chip->ngpio);
+
+		if (ret) {
+			dev_err(pctrl->dev, "Failed to add pin range\n");
+			gpiochip_remove(&pctrl->chip);
+			return ret;
+		}
 	}
 
 	ret = gpiochip_irqchip_add(chip,