diff mbox

[RFC] ARM: DTS: da850-evm: Refactor device tree layout

Message ID 20180427023549.13678-1-aford173@gmail.com (mailing list archive)
State New, archived
Headers show

Commit Message

Adam Ford April 27, 2018, 2:35 a.m. UTC
Many of the items in the device tree are already defined or partially
defined, so let's remove the redundancies and reduce the whitespace.

Signed-off-by: Adam Ford <aford173@gmail.com>

Comments

Sekhar Nori April 27, 2018, 4:57 a.m. UTC | #1
Hi Adam,

On Friday 27 April 2018 08:05 AM, Adam Ford wrote:
> Many of the items in the device tree are already defined or partially
> defined, so let's remove the redundancies and reduce the whitespace.

The patch is fine (and welcome, but for one nit below), but the
description needs to be better.

The main redundancy I can see is that node labels (like serial0, serial1
etc) are being redefined. So can you be clear on that. Also, the phandle
way of extending nodes is more "modern" (I dont quite recall if it was
common place back when the file was added in 2012).

Also, I would not call it "Refactor device tree layout" in subject. "use
phandles to extend nodes" is more apt.

> +
> +&pmx_core {
> +	status = "okay";
> +
> +	mcasp0_pins: pinmux_mcasp0_pins {
> +		pinctrl-single,bits = <
> +			/*
> +			 * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR,
> +			 * AFSR, AMUTE
> +			 */
> +			0x00 0x11111111 0xffffffff
> +			/* AXR11, AXR12 */
> +			0x04 0x00011000 0x000ff000
> +		>;
> +	};
> +	nand_pins: nand_pins {
> +		pinctrl-single,bits = <
> +			/* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */
> +			0x1c 0x10110110  0xf0ff0ff0
> +			/*
> +			 * EMA_D[0], EMA_D[1], EMA_D[2],
> +			 * EMA_D[3], EMA_D[4], EMA_D[5],
> +			 * EMA_D[6], EMA_D[7]
> +			 */
> +			0x24 0x11111111  0xffffffff
> +			/* EMA_A[1], EMA_A[2] */
> +			0x30 0x01100000  0x0ff00000
> +		>;
> +	};
> +};

Can you add an empty line after each node. This will make it consistent
with how its done in da850-lcdk.dts and da850-lego-ev3.dts

Thanks,
Sekhar
diff mbox

Patch

diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
index a56d43d53ba1..5bffbe74b6e4 100644
--- a/arch/arm/boot/dts/da850-evm.dts
+++ b/arch/arm/boot/dts/da850-evm.dts
@@ -27,146 +27,6 @@ 
 		spi0 = &spi1;
 	};
 
-	soc@1c00000 {
-		pmx_core: pinmux@14120 {
-			status = "okay";
-
-			mcasp0_pins: pinmux_mcasp0_pins {
-				pinctrl-single,bits = <
-					/*
-					 * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR,
-					 * AFSR, AMUTE
-					 */
-					0x00 0x11111111 0xffffffff
-					/* AXR11, AXR12 */
-					0x04 0x00011000 0x000ff000
-				>;
-			};
-			nand_pins: nand_pins {
-				pinctrl-single,bits = <
-					/* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */
-					0x1c 0x10110110  0xf0ff0ff0
-					/*
-					 * EMA_D[0], EMA_D[1], EMA_D[2],
-					 * EMA_D[3], EMA_D[4], EMA_D[5],
-					 * EMA_D[6], EMA_D[7]
-					 */
-					0x24 0x11111111  0xffffffff
-					/* EMA_A[1], EMA_A[2] */
-					0x30 0x01100000  0x0ff00000
-				>;
-			};
-		};
-		serial0: serial@42000 {
-			status = "okay";
-		};
-		serial1: serial@10c000 {
-			status = "okay";
-		};
-		serial2: serial@10d000 {
-			status = "okay";
-		};
-		rtc0: rtc@23000 {
-			status = "okay";
-		};
-		i2c0: i2c@22000 {
-			status = "okay";
-			clock-frequency = <100000>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins>;
-
-			tps: tps@48 {
-				reg = <0x48>;
-			};
-			tlv320aic3106: tlv320aic3106@18 {
-				#sound-dai-cells = <0>;
-				compatible = "ti,tlv320aic3106";
-				reg = <0x18>;
-				status = "okay";
-
-				/* Regulators */
-				IOVDD-supply = <&vdcdc2_reg>;
-				/* Derived from VBAT: Baseboard 3.3V / 1.8V */
-				AVDD-supply = <&vbat>;
-				DRVDD-supply = <&vbat>;
-				DVDD-supply = <&vbat>;
-			};
-			tca6416: gpio@20 {
-				compatible = "ti,tca6416";
-				reg = <0x20>;
-				gpio-controller;
-				#gpio-cells = <2>;
-			};
-		};
-		wdt: wdt@21000 {
-			status = "okay";
-		};
-		mmc0: mmc@40000 {
-			max-frequency = <50000000>;
-			bus-width = <4>;
-			status = "okay";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins>;
-			cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>;
-			wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>;
-		};
-		spi1: spi@30e000 {
-			status = "okay";
-			pinctrl-names = "default";
-			pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
-			flash: m25p80@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "m25p64";
-				spi-max-frequency = <30000000>;
-				m25p,fast-read;
-				reg = <0>;
-				partition@0 {
-					label = "U-Boot-SPL";
-					reg = <0x00000000 0x00010000>;
-					read-only;
-				};
-				partition@1 {
-					label = "U-Boot";
-					reg = <0x00010000 0x00080000>;
-					read-only;
-				};
-				partition@2 {
-					label = "U-Boot-Env";
-					reg = <0x00090000 0x00010000>;
-					read-only;
-				};
-				partition@3 {
-					label = "Kernel";
-					reg = <0x000a0000 0x00280000>;
-				};
-				partition@4 {
-					label = "Filesystem";
-					reg = <0x00320000 0x00400000>;
-				};
-				partition@5 {
-					label = "MAC-Address";
-					reg = <0x007f0000 0x00010000>;
-					read-only;
-				};
-			};
-		};
-		mdio: mdio@224000 {
-			status = "okay";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mdio_pins>;
-			bus_freq = <2200000>;
-		};
-		eth0: ethernet@220000 {
-			status = "okay";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mii_pins>;
-		};
-		gpio: gpio@226000 {
-			status = "okay";
-		};
-	};
-
 	backlight {
 		compatible = "gpio-backlight";
 		enable-gpios = <&gpio 48 GPIO_ACTIVE_HIGH>;
@@ -257,6 +117,142 @@ 
 	};
 };
 
+
+&pmx_core {
+	status = "okay";
+
+	mcasp0_pins: pinmux_mcasp0_pins {
+		pinctrl-single,bits = <
+			/*
+			 * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR,
+			 * AFSR, AMUTE
+			 */
+			0x00 0x11111111 0xffffffff
+			/* AXR11, AXR12 */
+			0x04 0x00011000 0x000ff000
+		>;
+	};
+	nand_pins: nand_pins {
+		pinctrl-single,bits = <
+			/* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */
+			0x1c 0x10110110  0xf0ff0ff0
+			/*
+			 * EMA_D[0], EMA_D[1], EMA_D[2],
+			 * EMA_D[3], EMA_D[4], EMA_D[5],
+			 * EMA_D[6], EMA_D[7]
+			 */
+			0x24 0x11111111  0xffffffff
+			/* EMA_A[1], EMA_A[2] */
+			0x30 0x01100000  0x0ff00000
+		>;
+	};
+};
+&serial0 {
+	status = "okay";
+};
+&serial1 {
+	status = "okay";
+};
+&serial2 {
+	status = "okay";
+};
+&rtc0 {
+	status = "okay";
+};
+&i2c0 {
+	status = "okay";
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	tps: tps@48 {
+		reg = <0x48>;
+	};
+	tlv320aic3106: tlv320aic3106@18 {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3106";
+		reg = <0x18>;
+		status = "okay";
+
+		/* Regulators */
+		IOVDD-supply = <&vdcdc2_reg>;
+		/* Derived from VBAT: Baseboard 3.3V / 1.8V */
+		AVDD-supply = <&vbat>;
+		DRVDD-supply = <&vbat>;
+		DVDD-supply = <&vbat>;
+	};
+	tca6416: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+&wdt {
+	status = "okay";
+};
+&mmc0 {
+	max-frequency = <50000000>;
+	bus-width = <4>;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>;
+};
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p64";
+		spi-max-frequency = <30000000>;
+		m25p,fast-read;
+		reg = <0>;
+		partition@0 {
+			label = "U-Boot-SPL";
+			reg = <0x00000000 0x00010000>;
+			read-only;
+		};
+		partition@1 {
+			label = "U-Boot";
+			reg = <0x00010000 0x00080000>;
+			read-only;
+		};
+		partition@2 {
+			label = "U-Boot-Env";
+			reg = <0x00090000 0x00010000>;
+			read-only;
+		};
+		partition@3 {
+			label = "Kernel";
+			reg = <0x000a0000 0x00280000>;
+		};
+		partition@4 {
+			label = "Filesystem";
+			reg = <0x00320000 0x00400000>;
+		};
+		partition@5 {
+			label = "MAC-Address";
+			reg = <0x007f0000 0x00010000>;
+			read-only;
+		};
+	};
+};
+&mdio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>;
+	bus_freq = <2200000>;
+};
+&eth0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mii_pins>;
+};
+
 /include/ "tps6507x.dtsi"
 
 &tps {