| Message ID | 20180514211610.26618-4-enric.balletbo@collabora.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi, On 2018년 05월 15일 06:16, Enric Balletbo i Serra wrote: > Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the > on-die termination (ODT) and auto power down parameters from kernel, > this patch adds the functionality to do this. Also, if DDR clock > frequency is lower than the on-die termination (ODT) disable frequency > this driver should disable the DDR ODT. I have a question. 'disable frequency' is the same meaning of 'disable the DDR ODT'? > > Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> > --- > > drivers/devfreq/rk3399_dmc.c | 50 ++++++++++++++++++++++++++++- > include/soc/rockchip/rockchip_sip.h | 1 + > 2 files changed, 50 insertions(+), 1 deletion(-) > > diff --git a/drivers/devfreq/rk3399_dmc.c b/drivers/devfreq/rk3399_dmc.c > index d5c03e5abe13..cc1bbca3fb15 100644 > --- a/drivers/devfreq/rk3399_dmc.c > +++ b/drivers/devfreq/rk3399_dmc.c > @@ -18,14 +18,17 @@ > #include <linux/devfreq.h> > #include <linux/devfreq-event.h> > #include <linux/interrupt.h> > +#include <linux/mfd/syscon.h> > #include <linux/module.h> > #include <linux/of.h> > #include <linux/platform_device.h> > #include <linux/pm_opp.h> > +#include <linux/regmap.h> > #include <linux/regulator/consumer.h> > #include <linux/rwsem.h> > #include <linux/suspend.h> > > +#include <soc/rockchip/rk3399_grf.h> > #include <soc/rockchip/rockchip_sip.h> > > struct dram_timing { > @@ -69,8 +72,11 @@ struct rk3399_dmcfreq { > struct mutex lock; > struct dram_timing timing; > struct regulator *vdd_center; > + struct regmap *regmap_pmu; > unsigned long rate, target_rate; > unsigned long volt, target_volt; > + unsigned int odt_dis_freq; > + int odt_pd_arg0, odt_pd_arg1; > }; > > static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, > @@ -80,6 +86,8 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, > struct dev_pm_opp *opp; > unsigned long old_clk_rate = dmcfreq->rate; > unsigned long target_volt, target_rate; > + struct arm_smccc_res res; > + int dram_flag; > int err; > > opp = devfreq_recommended_opp(dev, freq, flags); > @@ -95,6 +103,15 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, > > mutex_lock(&dmcfreq->lock); > > + dram_flag = 0; Also, if dram_flag is 0, it mean that disable ODT frequency? If it's right, you better to define the precise variables as following instead of just integer(0 or 1). For example, - ROCKCHIP_SIP_DRAM_FREQ_ENABLE - ROCKCHIP_SIP_DRAM_FREQ_DISABLE > + if (target_rate >= dmcfreq->odt_dis_freq) > + dram_flag = 1; > + > + arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, dmcfreq->odt_pd_arg0, > + dmcfreq->odt_pd_arg1, > + ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD, > + dram_flag, 0, 0, 0, &res); > + This operation is special for only rk3399_dmc. It is difficult to understand what to do. I recommend you better to add the detailed comment with code. > /* > * If frequency scaling from low to high, adjust voltage first. > * If frequency scaling from high to low, adjust frequency first. > @@ -294,11 +311,13 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) > { > struct arm_smccc_res res; > struct device *dev = &pdev->dev; > - struct device_node *np = pdev->dev.of_node; > + struct device_node *np = pdev->dev.of_node, *node; > struct rk3399_dmcfreq *data; > int ret, index, size; > uint32_t *timing; > struct dev_pm_opp *opp; > + u32 ddr_type; > + u32 val; > > data = devm_kzalloc(dev, sizeof(struct rk3399_dmcfreq), GFP_KERNEL); > if (!data) > @@ -334,6 +353,29 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) > return ret; > } > > + /* Try to find the optional reference to the pmu syscon */ > + node = of_parse_phandle(np, "rockchip,pmu", 0); > + if (node) { > + data->regmap_pmu = syscon_node_to_regmap(node); > + if (IS_ERR(data->regmap_pmu)) > + return PTR_ERR(data->regmap_pmu); > + } > + > + /* Get DDR type */ > + regmap_read(data->regmap_pmu, RK3399_PMUGRF_OS_REG2, &val); > + ddr_type = (val >> RK3399_PMUGRF_DDRTYPE_SHIFT) & > + RK3399_PMUGRF_DDRTYPE_MASK; > + > + /* Get the odt_dis_freq parameter in function of the DDR type */ > + if (ddr_type == RK3399_PMUGRF_DDRTYPE_DDR3) > + data->odt_dis_freq = data->timing.ddr3_odt_dis_freq; > + else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR3) > + data->odt_dis_freq = data->timing.lpddr3_odt_dis_freq; > + else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR4) > + data->odt_dis_freq = data->timing.lpddr4_odt_dis_freq; > + else > + return -EINVAL; > + how about using 'switch' statement? > /* > * Get dram timing and pass it to arm trust firmware, > * the dram drvier in arm trust firmware will get these > @@ -358,6 +400,12 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) > ROCKCHIP_SIP_CONFIG_DRAM_INIT, > 0, 0, 0, 0, &res); > > + data->odt_pd_arg0 = (data->timing.sr_idle & 0xff) | > + ((data->timing.sr_mc_gate_idle & 0xff) << 8) | > + ((data->timing.standby_idle & 0xffff) << 16); > + data->odt_pd_arg1 = (data->timing.pd_idle & 0xfff) | > + ((data->timing.srpd_lite_idle & 0xfff) << 16); > + odt_pd_arg0 and odt_pd_arg1 might be used for disabling/enabling the ODT frequency. As I commented, it depend on only rk3399_dmc. You better to add detailed comment. And I prefer to define the XXX_SHIFT/XXX_MASK definition instead of using 8/16/0xff/0xffff for the readability. > /* > * We add a devfreq driver to our parent since it has a device tree node > * with operating points. > diff --git a/include/soc/rockchip/rockchip_sip.h b/include/soc/rockchip/rockchip_sip.h > index 7e28092c4d3d..ad9482c56797 100644 > --- a/include/soc/rockchip/rockchip_sip.h > +++ b/include/soc/rockchip/rockchip_sip.h > @@ -23,5 +23,6 @@ > #define ROCKCHIP_SIP_CONFIG_DRAM_GET_RATE 0x05 > #define ROCKCHIP_SIP_CONFIG_DRAM_CLR_IRQ 0x06 > #define ROCKCHIP_SIP_CONFIG_DRAM_SET_PARAM 0x07 > +#define ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD 0x08 > > #endif >
Hi Chanwoo, I'll send a new version soon, just wanted to ask some questions here. See below. Missatge de Chanwoo Choi <cw00.choi@samsung.com> del dia dt., 15 de maig 2018 a les 0:21: > > Hi, > > On 2018년 05월 15일 06:16, Enric Balletbo i Serra wrote: > > Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the > > on-die termination (ODT) and auto power down parameters from kernel, > > this patch adds the functionality to do this. Also, if DDR clock > > frequency is lower than the on-die termination (ODT) disable frequency > > this driver should disable the DDR ODT. > > I have a question. > 'disable frequency' is the same meaning of 'disable the DDR ODT'? > Yes, the DT defines an odt_dis_freq parameter, when the DDR frequency is less than the value in this parameter we disable the ODT on the DRAM. > > > > Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> > > --- > > > > drivers/devfreq/rk3399_dmc.c | 50 ++++++++++++++++++++++++++++- > > include/soc/rockchip/rockchip_sip.h | 1 + > > 2 files changed, 50 insertions(+), 1 deletion(-) > > > > diff --git a/drivers/devfreq/rk3399_dmc.c b/drivers/devfreq/rk3399_dmc.c > > index d5c03e5abe13..cc1bbca3fb15 100644 > > --- a/drivers/devfreq/rk3399_dmc.c > > +++ b/drivers/devfreq/rk3399_dmc.c > > @@ -18,14 +18,17 @@ > > #include <linux/devfreq.h> > > #include <linux/devfreq-event.h> > > #include <linux/interrupt.h> > > +#include <linux/mfd/syscon.h> > > #include <linux/module.h> > > #include <linux/of.h> > > #include <linux/platform_device.h> > > #include <linux/pm_opp.h> > > +#include <linux/regmap.h> > > #include <linux/regulator/consumer.h> > > #include <linux/rwsem.h> > > #include <linux/suspend.h> > > > > +#include <soc/rockchip/rk3399_grf.h> > > #include <soc/rockchip/rockchip_sip.h> > > > > struct dram_timing { > > @@ -69,8 +72,11 @@ struct rk3399_dmcfreq { > > struct mutex lock; > > struct dram_timing timing; > > struct regulator *vdd_center; > > + struct regmap *regmap_pmu; > > unsigned long rate, target_rate; > > unsigned long volt, target_volt; > > + unsigned int odt_dis_freq; > > + int odt_pd_arg0, odt_pd_arg1; > > }; > > > > static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, > > @@ -80,6 +86,8 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, > > struct dev_pm_opp *opp; > > unsigned long old_clk_rate = dmcfreq->rate; > > unsigned long target_volt, target_rate; > > + struct arm_smccc_res res; > > + int dram_flag; > > int err; > > > > opp = devfreq_recommended_opp(dev, freq, flags); > > @@ -95,6 +103,15 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, > > > > mutex_lock(&dmcfreq->lock); > > > > + dram_flag = 0; > > Also, if dram_flag is 0, it mean that disable ODT frequency? Yes, not a good name, maybe I should just rename it to odt_enable to be more clear. > If it's right, you better to define the precise variables as following > instead of just integer(0 or 1). > For example, > - ROCKCHIP_SIP_DRAM_FREQ_ENABLE > - ROCKCHIP_SIP_DRAM_FREQ_DISABLE > > > + if (target_rate >= dmcfreq->odt_dis_freq) > > + dram_flag = 1; > > + > > + arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, dmcfreq->odt_pd_arg0, > > + dmcfreq->odt_pd_arg1, > > + ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD, > > + dram_flag, 0, 0, 0, &res); > > + > > This operation is special for only rk3399_dmc. It is difficult > to understand what to do. I recommend you better to add the detailed comment > with code. Will do. > > > /* > > * If frequency scaling from low to high, adjust voltage first. > > * If frequency scaling from high to low, adjust frequency first. > > @@ -294,11 +311,13 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) > > { > > struct arm_smccc_res res; > > struct device *dev = &pdev->dev; > > - struct device_node *np = pdev->dev.of_node; > > + struct device_node *np = pdev->dev.of_node, *node; > > struct rk3399_dmcfreq *data; > > int ret, index, size; > > uint32_t *timing; > > struct dev_pm_opp *opp; > > + u32 ddr_type; > > + u32 val; > > > > data = devm_kzalloc(dev, sizeof(struct rk3399_dmcfreq), GFP_KERNEL); > > if (!data) > > @@ -334,6 +353,29 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) > > return ret; > > } > > > > + /* Try to find the optional reference to the pmu syscon */ > > + node = of_parse_phandle(np, "rockchip,pmu", 0); > > + if (node) { > > + data->regmap_pmu = syscon_node_to_regmap(node); > > + if (IS_ERR(data->regmap_pmu)) > > + return PTR_ERR(data->regmap_pmu); > > + } > > + > > + /* Get DDR type */ > > + regmap_read(data->regmap_pmu, RK3399_PMUGRF_OS_REG2, &val); > > + ddr_type = (val >> RK3399_PMUGRF_DDRTYPE_SHIFT) & > > + RK3399_PMUGRF_DDRTYPE_MASK; > > + > > + /* Get the odt_dis_freq parameter in function of the DDR type */ > > + if (ddr_type == RK3399_PMUGRF_DDRTYPE_DDR3) > > + data->odt_dis_freq = data->timing.ddr3_odt_dis_freq; > > + else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR3) > > + data->odt_dis_freq = data->timing.lpddr3_odt_dis_freq; > > + else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR4) > > + data->odt_dis_freq = data->timing.lpddr4_odt_dis_freq; > > + else > > + return -EINVAL; > > + > > how about using 'switch' statement? > Ok > > /* > > * Get dram timing and pass it to arm trust firmware, > > * the dram drvier in arm trust firmware will get these > > @@ -358,6 +400,12 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) > > ROCKCHIP_SIP_CONFIG_DRAM_INIT, > > 0, 0, 0, 0, &res); > > > > + data->odt_pd_arg0 = (data->timing.sr_idle & 0xff) | > > + ((data->timing.sr_mc_gate_idle & 0xff) << 8) | > > + ((data->timing.standby_idle & 0xffff) << 16); > > + data->odt_pd_arg1 = (data->timing.pd_idle & 0xfff) | > > + ((data->timing.srpd_lite_idle & 0xfff) << 16); > > + > > odt_pd_arg0 and odt_pd_arg1 might be used for disabling/enabling the ODT frequency. > As I commented, it depend on only rk3399_dmc. You better to add detailed comment. > Ok > And I prefer to define the XXX_SHIFT/XXX_MASK definition instead of > using 8/16/0xff/0xffff for the readability. > I tried to add the XXX_SHIFT/XXX_MASK definitions and IMHO the readability is worst if I use a maximum line length of 80 characters. These masks are only used here, let me try to convince you by adding a good doc in the next version and if you still prefer I add the definition I'll do. > > /* > > * We add a devfreq driver to our parent since it has a device tree node > > * with operating points. > > diff --git a/include/soc/rockchip/rockchip_sip.h b/include/soc/rockchip/rockchip_sip.h > > index 7e28092c4d3d..ad9482c56797 100644 > > --- a/include/soc/rockchip/rockchip_sip.h > > +++ b/include/soc/rockchip/rockchip_sip.h > > @@ -23,5 +23,6 @@ > > #define ROCKCHIP_SIP_CONFIG_DRAM_GET_RATE 0x05 > > #define ROCKCHIP_SIP_CONFIG_DRAM_CLR_IRQ 0x06 > > #define ROCKCHIP_SIP_CONFIG_DRAM_SET_PARAM 0x07 > > +#define ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD 0x08 > > > > #endif > > > > > -- > Best Regards, > Chanwoo Choi > Samsung Electronics > > _______________________________________________ > Linux-rockchip mailing list > Linux-rockchip@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-rockchip Cheers, Enric
Hi Enric 2018-06-16 19:15 GMT+09:00 Enric Balletbo Serra <eballetbo@gmail.com>: > Hi Chanwoo, > > I'll send a new version soon, just wanted to ask some questions here. See below. > > Missatge de Chanwoo Choi <cw00.choi@samsung.com> del dia dt., 15 de > maig 2018 a les 0:21: >> >> Hi, >> >> On 2018년 05월 15일 06:16, Enric Balletbo i Serra wrote: >> > Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the >> > on-die termination (ODT) and auto power down parameters from kernel, >> > this patch adds the functionality to do this. Also, if DDR clock >> > frequency is lower than the on-die termination (ODT) disable frequency >> > this driver should disable the DDR ODT. >> >> I have a question. >> 'disable frequency' is the same meaning of 'disable the DDR ODT'? >> > > Yes, the DT defines an odt_dis_freq parameter, when the DDR frequency > is less than the value in this parameter we disable the ODT on the > DRAM. > >> > >> > Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> >> > --- >> > >> > drivers/devfreq/rk3399_dmc.c | 50 ++++++++++++++++++++++++++++- >> > include/soc/rockchip/rockchip_sip.h | 1 + >> > 2 files changed, 50 insertions(+), 1 deletion(-) >> > >> > diff --git a/drivers/devfreq/rk3399_dmc.c b/drivers/devfreq/rk3399_dmc.c >> > index d5c03e5abe13..cc1bbca3fb15 100644 >> > --- a/drivers/devfreq/rk3399_dmc.c >> > +++ b/drivers/devfreq/rk3399_dmc.c >> > @@ -18,14 +18,17 @@ >> > #include <linux/devfreq.h> >> > #include <linux/devfreq-event.h> >> > #include <linux/interrupt.h> >> > +#include <linux/mfd/syscon.h> >> > #include <linux/module.h> >> > #include <linux/of.h> >> > #include <linux/platform_device.h> >> > #include <linux/pm_opp.h> >> > +#include <linux/regmap.h> >> > #include <linux/regulator/consumer.h> >> > #include <linux/rwsem.h> >> > #include <linux/suspend.h> >> > >> > +#include <soc/rockchip/rk3399_grf.h> >> > #include <soc/rockchip/rockchip_sip.h> >> > >> > struct dram_timing { >> > @@ -69,8 +72,11 @@ struct rk3399_dmcfreq { >> > struct mutex lock; >> > struct dram_timing timing; >> > struct regulator *vdd_center; >> > + struct regmap *regmap_pmu; >> > unsigned long rate, target_rate; >> > unsigned long volt, target_volt; >> > + unsigned int odt_dis_freq; >> > + int odt_pd_arg0, odt_pd_arg1; >> > }; >> > >> > static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, >> > @@ -80,6 +86,8 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, >> > struct dev_pm_opp *opp; >> > unsigned long old_clk_rate = dmcfreq->rate; >> > unsigned long target_volt, target_rate; >> > + struct arm_smccc_res res; >> > + int dram_flag; >> > int err; >> > >> > opp = devfreq_recommended_opp(dev, freq, flags); >> > @@ -95,6 +103,15 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, >> > >> > mutex_lock(&dmcfreq->lock); >> > >> > + dram_flag = 0; >> >> Also, if dram_flag is 0, it mean that disable ODT frequency? > > Yes, not a good name, maybe I should just rename it to odt_enable to > be more clear. > >> If it's right, you better to define the precise variables as following >> instead of just integer(0 or 1). >> For example, >> - ROCKCHIP_SIP_DRAM_FREQ_ENABLE >> - ROCKCHIP_SIP_DRAM_FREQ_DISABLE >> >> > + if (target_rate >= dmcfreq->odt_dis_freq) >> > + dram_flag = 1; >> > + >> > + arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, dmcfreq->odt_pd_arg0, >> > + dmcfreq->odt_pd_arg1, >> > + ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD, >> > + dram_flag, 0, 0, 0, &res); >> > + >> >> This operation is special for only rk3399_dmc. It is difficult >> to understand what to do. I recommend you better to add the detailed comment >> with code. > > Will do. > >> >> > /* >> > * If frequency scaling from low to high, adjust voltage first. >> > * If frequency scaling from high to low, adjust frequency first. >> > @@ -294,11 +311,13 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) >> > { >> > struct arm_smccc_res res; >> > struct device *dev = &pdev->dev; >> > - struct device_node *np = pdev->dev.of_node; >> > + struct device_node *np = pdev->dev.of_node, *node; >> > struct rk3399_dmcfreq *data; >> > int ret, index, size; >> > uint32_t *timing; >> > struct dev_pm_opp *opp; >> > + u32 ddr_type; >> > + u32 val; >> > >> > data = devm_kzalloc(dev, sizeof(struct rk3399_dmcfreq), GFP_KERNEL); >> > if (!data) >> > @@ -334,6 +353,29 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) >> > return ret; >> > } >> > >> > + /* Try to find the optional reference to the pmu syscon */ >> > + node = of_parse_phandle(np, "rockchip,pmu", 0); >> > + if (node) { >> > + data->regmap_pmu = syscon_node_to_regmap(node); >> > + if (IS_ERR(data->regmap_pmu)) >> > + return PTR_ERR(data->regmap_pmu); >> > + } >> > + >> > + /* Get DDR type */ >> > + regmap_read(data->regmap_pmu, RK3399_PMUGRF_OS_REG2, &val); >> > + ddr_type = (val >> RK3399_PMUGRF_DDRTYPE_SHIFT) & >> > + RK3399_PMUGRF_DDRTYPE_MASK; >> > + >> > + /* Get the odt_dis_freq parameter in function of the DDR type */ >> > + if (ddr_type == RK3399_PMUGRF_DDRTYPE_DDR3) >> > + data->odt_dis_freq = data->timing.ddr3_odt_dis_freq; >> > + else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR3) >> > + data->odt_dis_freq = data->timing.lpddr3_odt_dis_freq; >> > + else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR4) >> > + data->odt_dis_freq = data->timing.lpddr4_odt_dis_freq; >> > + else >> > + return -EINVAL; >> > + >> >> how about using 'switch' statement? >> > > Ok > >> > /* >> > * Get dram timing and pass it to arm trust firmware, >> > * the dram drvier in arm trust firmware will get these >> > @@ -358,6 +400,12 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) >> > ROCKCHIP_SIP_CONFIG_DRAM_INIT, >> > 0, 0, 0, 0, &res); >> > >> > + data->odt_pd_arg0 = (data->timing.sr_idle & 0xff) | >> > + ((data->timing.sr_mc_gate_idle & 0xff) << 8) | >> > + ((data->timing.standby_idle & 0xffff) << 16); >> > + data->odt_pd_arg1 = (data->timing.pd_idle & 0xfff) | >> > + ((data->timing.srpd_lite_idle & 0xfff) << 16); >> > + >> >> odt_pd_arg0 and odt_pd_arg1 might be used for disabling/enabling the ODT frequency. >> As I commented, it depend on only rk3399_dmc. You better to add detailed comment. >> > > Ok > >> And I prefer to define the XXX_SHIFT/XXX_MASK definition instead of >> using 8/16/0xff/0xffff for the readability. >> > > I tried to add the XXX_SHIFT/XXX_MASK definitions and IMHO the > readability is worst if I use a maximum line length of 80 characters. > These masks are only used here, let me try to convince you by adding a > good doc in the next version and if you still prefer I add the > definition I'll do. If you add the some description and it would be only used on here, I don't force to add some definition such as _SHIFT, _MASK as you suggested. > >> > /* >> > * We add a devfreq driver to our parent since it has a device tree node >> > * with operating points. >> > diff --git a/include/soc/rockchip/rockchip_sip.h b/include/soc/rockchip/rockchip_sip.h >> > index 7e28092c4d3d..ad9482c56797 100644 >> > --- a/include/soc/rockchip/rockchip_sip.h >> > +++ b/include/soc/rockchip/rockchip_sip.h >> > @@ -23,5 +23,6 @@ >> > #define ROCKCHIP_SIP_CONFIG_DRAM_GET_RATE 0x05 >> > #define ROCKCHIP_SIP_CONFIG_DRAM_CLR_IRQ 0x06 >> > #define ROCKCHIP_SIP_CONFIG_DRAM_SET_PARAM 0x07 >> > +#define ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD 0x08 >> > >> > #endif >> > >> >> >> -- >> Best Regards, >> Chanwoo Choi >> Samsung Electronics >> >> _______________________________________________ >> Linux-rockchip mailing list >> Linux-rockchip@lists.infradead.org >> http://lists.infradead.org/mailman/listinfo/linux-rockchip > Cheers, > Enric
diff --git a/drivers/devfreq/rk3399_dmc.c b/drivers/devfreq/rk3399_dmc.c index d5c03e5abe13..cc1bbca3fb15 100644 --- a/drivers/devfreq/rk3399_dmc.c +++ b/drivers/devfreq/rk3399_dmc.c @@ -18,14 +18,17 @@ #include <linux/devfreq.h> #include <linux/devfreq-event.h> #include <linux/interrupt.h> +#include <linux/mfd/syscon.h> #include <linux/module.h> #include <linux/of.h> #include <linux/platform_device.h> #include <linux/pm_opp.h> +#include <linux/regmap.h> #include <linux/regulator/consumer.h> #include <linux/rwsem.h> #include <linux/suspend.h> +#include <soc/rockchip/rk3399_grf.h> #include <soc/rockchip/rockchip_sip.h> struct dram_timing { @@ -69,8 +72,11 @@ struct rk3399_dmcfreq { struct mutex lock; struct dram_timing timing; struct regulator *vdd_center; + struct regmap *regmap_pmu; unsigned long rate, target_rate; unsigned long volt, target_volt; + unsigned int odt_dis_freq; + int odt_pd_arg0, odt_pd_arg1; }; static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, @@ -80,6 +86,8 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, struct dev_pm_opp *opp; unsigned long old_clk_rate = dmcfreq->rate; unsigned long target_volt, target_rate; + struct arm_smccc_res res; + int dram_flag; int err; opp = devfreq_recommended_opp(dev, freq, flags); @@ -95,6 +103,15 @@ static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, mutex_lock(&dmcfreq->lock); + dram_flag = 0; + if (target_rate >= dmcfreq->odt_dis_freq) + dram_flag = 1; + + arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, dmcfreq->odt_pd_arg0, + dmcfreq->odt_pd_arg1, + ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD, + dram_flag, 0, 0, 0, &res); + /* * If frequency scaling from low to high, adjust voltage first. * If frequency scaling from high to low, adjust frequency first. @@ -294,11 +311,13 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) { struct arm_smccc_res res; struct device *dev = &pdev->dev; - struct device_node *np = pdev->dev.of_node; + struct device_node *np = pdev->dev.of_node, *node; struct rk3399_dmcfreq *data; int ret, index, size; uint32_t *timing; struct dev_pm_opp *opp; + u32 ddr_type; + u32 val; data = devm_kzalloc(dev, sizeof(struct rk3399_dmcfreq), GFP_KERNEL); if (!data) @@ -334,6 +353,29 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) return ret; } + /* Try to find the optional reference to the pmu syscon */ + node = of_parse_phandle(np, "rockchip,pmu", 0); + if (node) { + data->regmap_pmu = syscon_node_to_regmap(node); + if (IS_ERR(data->regmap_pmu)) + return PTR_ERR(data->regmap_pmu); + } + + /* Get DDR type */ + regmap_read(data->regmap_pmu, RK3399_PMUGRF_OS_REG2, &val); + ddr_type = (val >> RK3399_PMUGRF_DDRTYPE_SHIFT) & + RK3399_PMUGRF_DDRTYPE_MASK; + + /* Get the odt_dis_freq parameter in function of the DDR type */ + if (ddr_type == RK3399_PMUGRF_DDRTYPE_DDR3) + data->odt_dis_freq = data->timing.ddr3_odt_dis_freq; + else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR3) + data->odt_dis_freq = data->timing.lpddr3_odt_dis_freq; + else if (ddr_type == RK3399_PMUGRF_DDRTYPE_LPDDR4) + data->odt_dis_freq = data->timing.lpddr4_odt_dis_freq; + else + return -EINVAL; + /* * Get dram timing and pass it to arm trust firmware, * the dram drvier in arm trust firmware will get these @@ -358,6 +400,12 @@ static int rk3399_dmcfreq_probe(struct platform_device *pdev) ROCKCHIP_SIP_CONFIG_DRAM_INIT, 0, 0, 0, 0, &res); + data->odt_pd_arg0 = (data->timing.sr_idle & 0xff) | + ((data->timing.sr_mc_gate_idle & 0xff) << 8) | + ((data->timing.standby_idle & 0xffff) << 16); + data->odt_pd_arg1 = (data->timing.pd_idle & 0xfff) | + ((data->timing.srpd_lite_idle & 0xfff) << 16); + /* * We add a devfreq driver to our parent since it has a device tree node * with operating points. diff --git a/include/soc/rockchip/rockchip_sip.h b/include/soc/rockchip/rockchip_sip.h index 7e28092c4d3d..ad9482c56797 100644 --- a/include/soc/rockchip/rockchip_sip.h +++ b/include/soc/rockchip/rockchip_sip.h @@ -23,5 +23,6 @@ #define ROCKCHIP_SIP_CONFIG_DRAM_GET_RATE 0x05 #define ROCKCHIP_SIP_CONFIG_DRAM_CLR_IRQ 0x06 #define ROCKCHIP_SIP_CONFIG_DRAM_SET_PARAM 0x07 +#define ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD 0x08 #endif
Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the on-die termination (ODT) and auto power down parameters from kernel, this patch adds the functionality to do this. Also, if DDR clock frequency is lower than the on-die termination (ODT) disable frequency this driver should disable the DDR ODT. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> --- drivers/devfreq/rk3399_dmc.c | 50 ++++++++++++++++++++++++++++- include/soc/rockchip/rockchip_sip.h | 1 + 2 files changed, 50 insertions(+), 1 deletion(-)