diff mbox

[v2,1/2] ARM: dts: imx51-zii-scu3-esb: Add switch IRQ line pinumx config

Message ID 20180713173005.19552-2-andrew.smirnov@gmail.com (mailing list archive)
State New, archived
Headers show

Commit Message

Andrey Smirnov July 13, 2018, 5:30 p.m. UTC 
Instead of relying on default values, configure PAD_AUD3_BB_CK to be a
GPIO explicitly. While at, it change the pad configuration to enable
a 100K pull-down (the pin is used as IRQ_TYPE_LEVEL_HIGH).

Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
---
 arch/arm/boot/dts/imx51-zii-scu3-esb.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

Comments

Fabio Estevam July 13, 2018, 5:50 p.m. UTC | #1 
On Fri, Jul 13, 2018 at 2:30 PM, Andrey Smirnov
<andrew.smirnov@gmail.com> wrote:
> Instead of relying on default values, configure PAD_AUD3_BB_CK to be a
> GPIO explicitly. While at, it change the pad configuration to enable
> a 100K pull-down (the pin is used as IRQ_TYPE_LEVEL_HIGH).
>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
> Cc: Lucas Stach <l.stach@pengutronix.de>
> Cc: cphealy@gmail.com
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: Andrew Lunn <andrew@lunn.ch>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
diff mbox

Patch

diff --git a/arch/arm/boot/dts/imx51-zii-scu3-esb.dts b/arch/arm/boot/dts/imx51-zii-scu3-esb.dts
index 2941a92d40f1..0bb42c00d72b 100644
--- a/arch/arm/boot/dts/imx51-zii-scu3-esb.dts
+++ b/arch/arm/boot/dts/imx51-zii-scu3-esb.dts
@@ -221,6 +221,8 @@ 
 			interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_switch>;
 
 			ports {
 				#address-cells = <1>;
@@ -426,6 +428,12 @@ 
 		>;
 	};
 
+	pinctrl_switch: switchgrp {
+		fsl,pins = <
+			MX51_PAD_AUD3_BB_CK__GPIO4_20		0xc5
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX51_PAD_UART1_RXD__UART1_RXD		0x1c5