| Message ID | 20180804070355.14857-1-manu@freebsd.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/7] dt-bindings: Add DT bindings documentation for Allwinner Thermal Sensor Controller | expand |
On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > This patch adds documentation for Device-Tree bindings for the Allwinner > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > --- > .../bindings/thermal/allwinner-thermal.txt | 41 +++++++++++++++++++ > 1 file changed, 41 insertions(+) > create mode 100644 Documentation/devicetree/bindings/thermal/allwinner-thermal.txt > > diff --git a/Documentation/devicetree/bindings/thermal/allwinner-thermal.txt b/Documentation/devicetree/bindings/thermal/allwinner-thermal.txt > new file mode 100644 > index 000000000000..5810d44cf495 > --- /dev/null > +++ b/Documentation/devicetree/bindings/thermal/allwinner-thermal.txt > @@ -0,0 +1,41 @@ > +* Thermal Sensor Controller on Allwinner SoCs > + > +Required properties: > +- compatible : should be "allwinner,<name>-ths" > + "allwinner,sun8i-h3-ths": found on H3 and H2+ SoCs > + "allwinner,sun50i-h5-ths": found on H5 SoC > + "allwinner,sun50i-a64-ths": found on H5 SoC > +- reg : physical base address of the controller and length of memory mapped > + region. > +- interrupts : The interrupt number to the cpu. The interrupt specifier format > + depends on the interrupt controller. Just need to say how many entries (and order if more than one). > +- clocks : Must contain an entry for each entry in clock-names. > +- clock-names : Shall be "apb" for the bus, and "ths" for > + the peripheral clock. > +- resets : Must contain an entry for each entry in reset-names. > + See ../reset/reset.txt for details. > +- reset-names : Must be "apb". > +- #thermal-sensor-cells : Depend on the SoC > + For H3 should be 0 > + For H5 should be 1 > + For A64 should be 2 > + See ./thermal.txt for a description. > +- nvmem-cells : Phandle to the calibration data > +- nvmem-cell-names = Should be "ths-calib" > + > +Example: > + > +ths: thermal_sensor@1c25000 { thermal-sensor@... > + compatible = "allwinner,sun8i-h3-ths"; > + reg = <0x01c25000 0x100>; > + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>; > + clock-names = "apb", "ths"; > + resets = <&ccu RST_BUS_THS>; > + reset-names = "apb"; > + #thermal-sensor-cells = <0>; > + status = "disabled"; > + > + nvmem-cells = <&ths_calib>; > + nvmem-cell-names = "ths-calib"; > +}; > -- > 2.18.0 >
On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > This patch adds documentation for Device-Tree bindings for the Allwinner > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> I'm not going to merge a binding for a device that doesn't have any driver implemented at the moment in Linux. Maxime
On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > This patch adds documentation for Device-Tree bindings for the Allwinner > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > I'm not going to merge a binding for a device that doesn't have any > driver implemented at the moment in Linux. I'll take it then. Linux is not the only DT client. Rob
On Mon, 20 Aug 2018 07:41:22 -0600 Rob Herring <robh+dt@kernel.org> wrote: > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > I'm not going to merge a binding for a device that doesn't have any > > driver implemented at the moment in Linux. > > I'll take it then. Linux is not the only DT client. > > Rob Thanks Rob, I'll send a V2 shortly with the modification you asked and some minor others documentation corrections.
On Mon, Aug 20, 2018 at 07:41:22AM -0600, Rob Herring wrote: > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > I'm not going to merge a binding for a device that doesn't have any > > driver implemented at the moment in Linux. > > I'll take it then. Linux is not the only DT client. Then don't complain if we ever have to break the ABI. We never tested that hardware, never had any code running on it, and it *will* cause some issues. For example, the calibration data have never been used and how they should be represented have never been described, since no one ever actually tried to use it. And sure, Linux is not the only DT client. Just like FreeBSD isn't. Maxime
On Mon, 20 Aug 2018 16:07:37 +0200 Maxime Ripard <maxime.ripard@bootlin.com> wrote: > On Mon, Aug 20, 2018 at 07:41:22AM -0600, Rob Herring wrote: > > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > > > I'm not going to merge a binding for a device that doesn't have any > > > driver implemented at the moment in Linux. > > > > I'll take it then. Linux is not the only DT client. > > Then don't complain if we ever have to break the ABI. We never tested > that hardware, never had any code running on it, and it *will* cause > some issues. For example, the calibration data have never been used > and how they should be represented have never been described, since no > one ever actually tried to use it. > > And sure, Linux is not the only DT client. Just like FreeBSD isn't. > > Maxime Maxime, What kind of data would you need for me to make things better ? We have the driver in FreeBSD for almost two years now, whne I started to see how to upstream it I noticed a lot of problems and spent 4 or 5 days to try on all the SoCs mentionned in the serie, the only SoC I didn't include it the A83T as for some reason I couldn't make the driver work. I just hope that you understand that we cannot wait for Linux to have a driver to have some bindings. Cheers,
On Mon, Aug 20, 2018 at 9:07 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > On Mon, Aug 20, 2018 at 07:41:22AM -0600, Rob Herring wrote: > > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > > > I'm not going to merge a binding for a device that doesn't have any > > > driver implemented at the moment in Linux. > > > > I'll take it then. Linux is not the only DT client. > > Then don't complain if we ever have to break the ABI. My only complaint is when breaking ABIs and not being clear about doing so. Otherwise, it is up to platform maintainers to not upset their users (including if some of those users are FreeBSD). > We never tested > that hardware, never had any code running on it, and it *will* cause > some issues. For example, the calibration data have never been used > and how they should be represented have never been described, since no > one ever actually tried to use it. Then perhaps that part of the binding should be omitted for now. But I don't see how if this works for FreeBSD how it wouldn't for Linux. Rob
Hi, On Mon, Aug 20, 2018 at 04:27:15PM +0200, Emmanuel Vadot wrote: > On Mon, 20 Aug 2018 16:07:37 +0200 > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > On Mon, Aug 20, 2018 at 07:41:22AM -0600, Rob Herring wrote: > > > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > > > > > I'm not going to merge a binding for a device that doesn't have any > > > > driver implemented at the moment in Linux. > > > > > > I'll take it then. Linux is not the only DT client. > > > > Then don't complain if we ever have to break the ABI. We never tested > > that hardware, never had any code running on it, and it *will* cause > > some issues. For example, the calibration data have never been used > > and how they should be represented have never been described, since no > > one ever actually tried to use it. > > > > And sure, Linux is not the only DT client. Just like FreeBSD isn't. > > What kind of data would you need for me to make things better ? > We have the driver in FreeBSD for almost two years now, whne I started > to see how to upstream it I noticed a lot of problems and spent 4 or 5 > days to try on all the SoCs mentionned in the serie, the only SoC I > didn't include it the A83T as for some reason I couldn't make the > driver work. Do you have a link to that driver? How and how much did you test it? Are you using the calibration data stored in the SID? > I just hope that you understand that we cannot wait for Linux to > have a driver to have some bindings. Just like I'm sure you can understand that just merging the DT bits without testing anything caused some troubles in the past, and I don't want to discover it in a year from now. Maxime
Hi, On Fri, 24 Aug 2018 16:58:40 +0200 Maxime Ripard <maxime.ripard@bootlin.com> wrote: > Hi, > > On Mon, Aug 20, 2018 at 04:27:15PM +0200, Emmanuel Vadot wrote: > > On Mon, 20 Aug 2018 16:07:37 +0200 > > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > On Mon, Aug 20, 2018 at 07:41:22AM -0600, Rob Herring wrote: > > > > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > > > > > > > I'm not going to merge a binding for a device that doesn't have any > > > > > driver implemented at the moment in Linux. > > > > > > > > I'll take it then. Linux is not the only DT client. > > > > > > Then don't complain if we ever have to break the ABI. We never tested > > > that hardware, never had any code running on it, and it *will* cause > > > some issues. For example, the calibration data have never been used > > > and how they should be represented have never been described, since no > > > one ever actually tried to use it. > > > > > > And sure, Linux is not the only DT client. Just like FreeBSD isn't. > > > > What kind of data would you need for me to make things better ? > > We have the driver in FreeBSD for almost two years now, whne I started > > to see how to upstream it I noticed a lot of problems and spent 4 or 5 > > days to try on all the SoCs mentionned in the serie, the only SoC I > > didn't include it the A83T as for some reason I couldn't make the > > driver work. > > Do you have a link to that driver? https://github.com/freebsd/freebsd/blob/master/sys/arm/allwinner/aw_thermal.c > How and how much did you test it? Using a cheap IR thermometer as it's all I can afford. Then running multiples cpufreq-a53 process and comparing the result. Did the same without using the calibration data, result where closer when I used them. > Are you using the calibration data stored in the SID? Yes, which is why the serie contain the nvmem cell for the SID. > > > I just hope that you understand that we cannot wait for Linux to > > have a driver to have some bindings. > > Just like I'm sure you can understand that just merging the DT bits > without testing anything caused some troubles in the past, and I don't > want to discover it in a year from now. I do, I don't like wrong DT info as much as you do I think. I had the unfortunate event to find that the sun4i-a10-timer compatible used in every soc is plain wrong for !A10 and !A13, patches comming soon. I want those bits merged but I also want that they reflect reality, this is not a hard driver to do, NetBSD also have one I think, maybe OpenBSD do to. > Maxime > > -- > Maxime Ripard, Bootlin > Embedded Linux and Kernel engineering > https://bootlin.com
On Fri, Aug 24, 2018 at 09:59:21PM +0200, Emmanuel Vadot wrote: > > Hi, > > On Fri, 24 Aug 2018 16:58:40 +0200 > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > Hi, > > > > On Mon, Aug 20, 2018 at 04:27:15PM +0200, Emmanuel Vadot wrote: > > > On Mon, 20 Aug 2018 16:07:37 +0200 > > > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > On Mon, Aug 20, 2018 at 07:41:22AM -0600, Rob Herring wrote: > > > > > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > > > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > > > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > > > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > > > > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > > > > > > > > > I'm not going to merge a binding for a device that doesn't have any > > > > > > driver implemented at the moment in Linux. > > > > > > > > > > I'll take it then. Linux is not the only DT client. > > > > > > > > Then don't complain if we ever have to break the ABI. We never tested > > > > that hardware, never had any code running on it, and it *will* cause > > > > some issues. For example, the calibration data have never been used > > > > and how they should be represented have never been described, since no > > > > one ever actually tried to use it. > > > > > > > > And sure, Linux is not the only DT client. Just like FreeBSD isn't. > > > > > > What kind of data would you need for me to make things better ? > > > We have the driver in FreeBSD for almost two years now, whne I started > > > to see how to upstream it I noticed a lot of problems and spent 4 or 5 > > > days to try on all the SoCs mentionned in the serie, the only SoC I > > > didn't include it the A83T as for some reason I couldn't make the > > > driver work. > > > > Do you have a link to that driver? > > https://github.com/freebsd/freebsd/blob/master/sys/arm/allwinner/aw_thermal.c > > > How and how much did you test it? > > Using a cheap IR thermometer as it's all I can afford. > Then running multiples cpufreq-a53 process and comparing the result. > Did the same without using the calibration data, result where closer > when I used them. > > > Are you using the calibration data stored in the SID? > > Yes, which is why the serie contain the nvmem cell for the SID. > > > > > > I just hope that you understand that we cannot wait for Linux to > > > have a driver to have some bindings. > > > > Just like I'm sure you can understand that just merging the DT bits > > without testing anything caused some troubles in the past, and I don't > > want to discover it in a year from now. > > I do, I don't like wrong DT info as much as you do I think. I had > the unfortunate event to find that the sun4i-a10-timer compatible used > in every soc is plain wrong for !A10 and !A13, patches comming soon. > I want those bits merged but I also want that they reflect reality, > this is not a hard driver to do, NetBSD also have one I think, maybe > OpenBSD do to. I would prefer to see a series of DT bindings + driver. Can you send your next iteration with the driver so we can review both together? > > > Maxime > > > > -- > > Maxime Ripard, Bootlin > > Embedded Linux and Kernel engineering > > https://bootlin.com > > > -- > Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org>
Hi, On Fri, 24 Aug 2018 16:03:40 -0700 Eduardo Valentin <edubezval@gmail.com> wrote: > On Fri, Aug 24, 2018 at 09:59:21PM +0200, Emmanuel Vadot wrote: > > > > Hi, > > > > On Fri, 24 Aug 2018 16:58:40 +0200 > > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > Hi, > > > > > > On Mon, Aug 20, 2018 at 04:27:15PM +0200, Emmanuel Vadot wrote: > > > > On Mon, 20 Aug 2018 16:07:37 +0200 > > > > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > > > On Mon, Aug 20, 2018 at 07:41:22AM -0600, Rob Herring wrote: > > > > > > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > > > > > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > > > > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > > > > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > > > > > > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > > > > > > > > > > > I'm not going to merge a binding for a device that doesn't have any > > > > > > > driver implemented at the moment in Linux. > > > > > > > > > > > > I'll take it then. Linux is not the only DT client. > > > > > > > > > > Then don't complain if we ever have to break the ABI. We never tested > > > > > that hardware, never had any code running on it, and it *will* cause > > > > > some issues. For example, the calibration data have never been used > > > > > and how they should be represented have never been described, since no > > > > > one ever actually tried to use it. > > > > > > > > > > And sure, Linux is not the only DT client. Just like FreeBSD isn't. > > > > > > > > What kind of data would you need for me to make things better ? > > > > We have the driver in FreeBSD for almost two years now, whne I started > > > > to see how to upstream it I noticed a lot of problems and spent 4 or 5 > > > > days to try on all the SoCs mentionned in the serie, the only SoC I > > > > didn't include it the A83T as for some reason I couldn't make the > > > > driver work. > > > > > > Do you have a link to that driver? > > > > https://github.com/freebsd/freebsd/blob/master/sys/arm/allwinner/aw_thermal.c > > > > > How and how much did you test it? > > > > Using a cheap IR thermometer as it's all I can afford. > > Then running multiples cpufreq-a53 process and comparing the result. > > Did the same without using the calibration data, result where closer > > when I used them. > > > > > Are you using the calibration data stored in the SID? > > > > Yes, which is why the serie contain the nvmem cell for the SID. > > > > > > > > > I just hope that you understand that we cannot wait for Linux to > > > > have a driver to have some bindings. > > > > > > Just like I'm sure you can understand that just merging the DT bits > > > without testing anything caused some troubles in the past, and I don't > > > want to discover it in a year from now. > > > > I do, I don't like wrong DT info as much as you do I think. I had > > the unfortunate event to find that the sun4i-a10-timer compatible used > > in every soc is plain wrong for !A10 and !A13, patches comming soon. > > I want those bits merged but I also want that they reflect reality, > > this is not a hard driver to do, NetBSD also have one I think, maybe > > OpenBSD do to. > > > I would prefer to see a series of DT bindings + driver. Can you send > your next iteration with the driver so we can review both together? You mean a link to the FreeBSD driver (and OpenBSD since they have one too) in the cover letter ? > > > > > Maxime > > > > > > -- > > > Maxime Ripard, Bootlin > > > Embedded Linux and Kernel engineering > > > https://bootlin.com > > > > > > -- > > Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org> > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Sat, Aug 25, 2018 at 05:43:52PM +0200, Emmanuel Vadot wrote: > > Hi, > > On Fri, 24 Aug 2018 16:03:40 -0700 > Eduardo Valentin <edubezval@gmail.com> wrote: > > > On Fri, Aug 24, 2018 at 09:59:21PM +0200, Emmanuel Vadot wrote: > > > > > > Hi, > > > > > > On Fri, 24 Aug 2018 16:58:40 +0200 > > > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > Hi, > > > > > > > > On Mon, Aug 20, 2018 at 04:27:15PM +0200, Emmanuel Vadot wrote: > > > > > On Mon, 20 Aug 2018 16:07:37 +0200 > > > > > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > > > > > On Mon, Aug 20, 2018 at 07:41:22AM -0600, Rob Herring wrote: > > > > > > > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > > > > > > > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > > > > > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > > > > > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > > > > > > > > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > > > > > > > > > > > > > I'm not going to merge a binding for a device that doesn't have any > > > > > > > > driver implemented at the moment in Linux. > > > > > > > > > > > > > > I'll take it then. Linux is not the only DT client. > > > > > > > > > > > > Then don't complain if we ever have to break the ABI. We never tested > > > > > > that hardware, never had any code running on it, and it *will* cause > > > > > > some issues. For example, the calibration data have never been used > > > > > > and how they should be represented have never been described, since no > > > > > > one ever actually tried to use it. > > > > > > > > > > > > And sure, Linux is not the only DT client. Just like FreeBSD isn't. > > > > > > > > > > What kind of data would you need for me to make things better ? > > > > > We have the driver in FreeBSD for almost two years now, whne I started > > > > > to see how to upstream it I noticed a lot of problems and spent 4 or 5 > > > > > days to try on all the SoCs mentionned in the serie, the only SoC I > > > > > didn't include it the A83T as for some reason I couldn't make the > > > > > driver work. > > > > > > > > Do you have a link to that driver? > > > > > > https://github.com/freebsd/freebsd/blob/master/sys/arm/allwinner/aw_thermal.c > > > > > > > How and how much did you test it? > > > > > > Using a cheap IR thermometer as it's all I can afford. > > > Then running multiples cpufreq-a53 process and comparing the result. > > > Did the same without using the calibration data, result where closer > > > when I used them. > > > > > > > Are you using the calibration data stored in the SID? > > > > > > Yes, which is why the serie contain the nvmem cell for the SID. > > > > > > > > > > > > I just hope that you understand that we cannot wait for Linux to > > > > > have a driver to have some bindings. > > > > > > > > Just like I'm sure you can understand that just merging the DT bits > > > > without testing anything caused some troubles in the past, and I don't > > > > want to discover it in a year from now. > > > > > > I do, I don't like wrong DT info as much as you do I think. I had > > > the unfortunate event to find that the sun4i-a10-timer compatible used > > > in every soc is plain wrong for !A10 and !A13, patches comming soon. > > > I want those bits merged but I also want that they reflect reality, > > > this is not a hard driver to do, NetBSD also have one I think, maybe > > > OpenBSD do to. > > > > > > I would prefer to see a series of DT bindings + driver. Can you send > > your next iteration with the driver so we can review both together? > > You mean a link to the FreeBSD driver (and OpenBSD since they have one > too) in the cover letter ? That would definitely be valuable, yes, thanks! Maxime
On Fri, Aug 24, 2018 at 09:59:21PM +0200, Emmanuel Vadot wrote: > > Hi, > > On Fri, 24 Aug 2018 16:58:40 +0200 > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > Hi, > > > > On Mon, Aug 20, 2018 at 04:27:15PM +0200, Emmanuel Vadot wrote: > > > On Mon, 20 Aug 2018 16:07:37 +0200 > > > Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > On Mon, Aug 20, 2018 at 07:41:22AM -0600, Rob Herring wrote: > > > > > On Mon, Aug 20, 2018 at 5:17 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > > > > > > > > > On Sat, Aug 04, 2018 at 09:03:49AM +0200, Emmanuel Vadot wrote: > > > > > > > This patch adds documentation for Device-Tree bindings for the Allwinner > > > > > > > Thermal Sensor Controller found on the H3, H5 and A64 SoCs > > > > > > > > > > > > > > Signed-off-by: Emmanuel Vadot <manu@freebsd.org> > > > > > > > > > > > > I'm not going to merge a binding for a device that doesn't have any > > > > > > driver implemented at the moment in Linux. > > > > > > > > > > I'll take it then. Linux is not the only DT client. > > > > > > > > Then don't complain if we ever have to break the ABI. We never tested > > > > that hardware, never had any code running on it, and it *will* cause > > > > some issues. For example, the calibration data have never been used > > > > and how they should be represented have never been described, since no > > > > one ever actually tried to use it. > > > > > > > > And sure, Linux is not the only DT client. Just like FreeBSD isn't. > > > > > > What kind of data would you need for me to make things better ? > > > We have the driver in FreeBSD for almost two years now, whne I started > > > to see how to upstream it I noticed a lot of problems and spent 4 or 5 > > > days to try on all the SoCs mentionned in the serie, the only SoC I > > > didn't include it the A83T as for some reason I couldn't make the > > > driver work. > > > > Do you have a link to that driver? > > https://github.com/freebsd/freebsd/blob/master/sys/arm/allwinner/aw_thermal.c > > > How and how much did you test it? > > Using a cheap IR thermometer as it's all I can afford. > Then running multiples cpufreq-a53 process and comparing the result. > Did the same without using the calibration data, result where closer > when I used them. Ok. > > Are you using the calibration data stored in the SID? > > Yes, which is why the serie contain the nvmem cell for the SID. Ok. > > > > > I just hope that you understand that we cannot wait for Linux to > > > have a driver to have some bindings. > > > > Just like I'm sure you can understand that just merging the DT bits > > without testing anything caused some troubles in the past, and I don't > > want to discover it in a year from now. > > I do, I don't like wrong DT info as much as you do I think. I had > the unfortunate event to find that the sun4i-a10-timer compatible used > in every soc is plain wrong for !A10 and !A13, patches comming soon. > I want those bits merged but I also want that they reflect reality, > this is not a hard driver to do, NetBSD also have one I think, maybe > OpenBSD do to. I guess these one went un-noticed because they are not the default source of time keeping and events in the kernel. Thanks! Maxime
diff --git a/Documentation/devicetree/bindings/thermal/allwinner-thermal.txt b/Documentation/devicetree/bindings/thermal/allwinner-thermal.txt new file mode 100644 index 000000000000..5810d44cf495 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/allwinner-thermal.txt @@ -0,0 +1,41 @@ +* Thermal Sensor Controller on Allwinner SoCs + +Required properties: +- compatible : should be "allwinner,<name>-ths" + "allwinner,sun8i-h3-ths": found on H3 and H2+ SoCs + "allwinner,sun50i-h5-ths": found on H5 SoC + "allwinner,sun50i-a64-ths": found on H5 SoC +- reg : physical base address of the controller and length of memory mapped + region. +- interrupts : The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Shall be "apb" for the bus, and "ths" for + the peripheral clock. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must be "apb". +- #thermal-sensor-cells : Depend on the SoC + For H3 should be 0 + For H5 should be 1 + For A64 should be 2 + See ./thermal.txt for a description. +- nvmem-cells : Phandle to the calibration data +- nvmem-cell-names = Should be "ths-calib" + +Example: + +ths: thermal_sensor@1c25000 { + compatible = "allwinner,sun8i-h3-ths"; + reg = <0x01c25000 0x100>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>; + clock-names = "apb", "ths"; + resets = <&ccu RST_BUS_THS>; + reset-names = "apb"; + #thermal-sensor-cells = <0>; + status = "disabled"; + + nvmem-cells = <&ths_calib>; + nvmem-cell-names = "ths-calib"; +};
This patch adds documentation for Device-Tree bindings for the Allwinner Thermal Sensor Controller found on the H3, H5 and A64 SoCs Signed-off-by: Emmanuel Vadot <manu@freebsd.org> --- .../bindings/thermal/allwinner-thermal.txt | 41 +++++++++++++++++++ 1 file changed, 41 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/allwinner-thermal.txt