diff mbox series

[DO,NOT,MERGE,v8,14/15] arm64: dts: allwinner: a64-pine64-lts: Enable Feiyang FY07024DI26A30-D DSI panel

Message ID 20190311133637.18334-15-jagan@amarulasolutions.com (mailing list archive)
State New, archived
Headers show
Series drm/sun4i: Allwinner A64 MIPI-DSI support | expand

Commit Message

Jagan Teki March 11, 2019, 1:36 p.m. UTC
Feiyang FY07024DI26A30-D MIPI_DSI panel is desiged to attach with
DSI connector on pine64 boards, enable the same for pine64 LTS.

DSI panel connected via board DSI port with,
- DC1SW as AVDD supply
- DLDO2 as DVDD supply
- DLDO1 as VCC-DSI supply
- PD24 gpio for reset pin
- PH10 gpio for backlight enable pin

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
---
 .../dts/allwinner/sun50i-a64-pine64-lts.dts   | 39 +++++++++++++++++++
 1 file changed, 39 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts
index 72d6961dc312..341b1c035604 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts
@@ -5,9 +5,48 @@ 
  */
 
 #include "sun50i-a64-sopine-baseboard.dts"
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Pine64 LTS";
 	compatible = "pine64,pine64-lts", "allwinner,sun50i-r18",
 		     "allwinner,sun50i-a64";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <1 2 4 8 16 32 64 128 512>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PH10 */
+	};
+};
+
+&de {
+	status = "okay";
+};
+
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	vcc-dsi-supply = <&reg_dldo1>;		/* VCC3V3-DSI */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "feiyang,fy07024di26a30d";
+		reg = <0>;
+		avdd-supply = <&reg_dc1sw>;	/* VCC-LCD */
+		dvdd-supply = <&reg_dldo2>;	/* VCC-MIPI */
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */
+		backlight = <&backlight>;
+	};
+};
+
+&r_pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_pwm_pin>;
+	status = "okay";
 };