| Message ID | 20190315130825.9005-4-jagan@amarulasolutions.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | drm/bridge: Add ICN6211 MIPI-DSI/RGB bridge | expand |
Hi, On Fri, 2019-03-15 at 18:38 +0530, Jagan Teki wrote: > Some display panels would come up with a non-DSI output which > can have an option to connect DSI interface by means of bridge > convertor. > > This DSI to non-DSI bridge convertor would require a bridge > driver that would communicate the DSI controller for bridge > functionalities. > > So, add support for bridge functionalities in Allwinner DSI > controller. See a few comments below. > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> > --- > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 65 +++++++++++++++++++------- > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h | 1 + > 2 files changed, 49 insertions(+), 17 deletions(-) > > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > index 0960b96b62cc..64d74313b842 100644 > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > @@ -781,6 +781,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) > if (!IS_ERR(dsi->panel)) > drm_panel_prepare(dsi->panel); > > + if (!IS_ERR(dsi->bridge)) > + drm_bridge_pre_enable(dsi->bridge); > + > /* > * FIXME: This should be moved after the switch to HS mode. > * > @@ -796,6 +799,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) > if (!IS_ERR(dsi->panel)) > drm_panel_enable(dsi->panel); > > + if (!IS_ERR(dsi->bridge)) > + drm_bridge_enable(dsi->bridge); > + > sun6i_dsi_start(dsi, DSI_START_HSC); > > udelay(1000); > @@ -812,6 +818,9 @@ static void sun6i_dsi_encoder_disable(struct drm_encoder *encoder) > if (!IS_ERR(dsi->panel)) { > drm_panel_disable(dsi->panel); > drm_panel_unprepare(dsi->panel); > + } else if (!IS_ERR(dsi->bridge)) { > + drm_bridge_disable(dsi->bridge); > + drm_bridge_post_disable(dsi->bridge); > } > > phy_power_off(dsi->dphy); > @@ -973,11 +982,16 @@ static int sun6i_dsi_attach(struct mipi_dsi_host *host, > struct sun6i_dsi *dsi = host_to_sun6i_dsi(host); > > dsi->device = device; > - dsi->panel = of_drm_find_panel(device->dev.of_node); > - if (IS_ERR(dsi->panel)) > - return PTR_ERR(dsi->panel); > > - dev_info(host->dev, "Attached device %s\n", device->name); > + dsi->bridge = of_drm_find_bridge(device->dev.of_node); > + if (!dsi->bridge) { You are using IS_ERR to check that the bridge is alive in the changes above, but switch to checking that it's non-NULL at this point. Are both guaranteed to be interchangeable? > + dsi->panel = of_drm_find_panel(device->dev.of_node); > + if (IS_ERR(dsi->panel)) > + return PTR_ERR(dsi->panel); > + } You should probably use drm_of_find_panel_or_bridge instead of duplicating the logic here. > + dev_info(host->dev, "Attached %s %s\n", > + dsi->bridge ? "bridge" : "panel", device->name); > > return 0; > } > @@ -1055,8 +1069,10 @@ static int sun6i_dsi_bind(struct device *dev, struct device *master, > struct sun4i_tcon *tcon0 = sun4i_get_tcon0(drm); > int ret; > > - if (!dsi->panel) > + if (!(dsi->panel || dsi->bridge)) { > + dev_info(drm->dev, "No panel or bridge found... DSI output disabled\n"); > return -EPROBE_DEFER; > + } > > dsi->drv = drv; > > @@ -1078,19 +1094,29 @@ static int sun6i_dsi_bind(struct device *dev, struct device *master, > } > dsi->encoder.possible_crtcs = BIT(0); > > - drm_connector_helper_add(&dsi->connector, > - &sun6i_dsi_connector_helper_funcs); > - ret = drm_connector_init(drm, &dsi->connector, > - &sun6i_dsi_connector_funcs, > - DRM_MODE_CONNECTOR_DSI); > - if (ret) { > - dev_err(dsi->dev, > - "Couldn't initialise the DSI connector\n"); > - goto err_cleanup_connector; > + if (dsi->panel) { > + drm_connector_helper_add(&dsi->connector, > + &sun6i_dsi_connector_helper_funcs); > + ret = drm_connector_init(drm, &dsi->connector, > + &sun6i_dsi_connector_funcs, > + DRM_MODE_CONNECTOR_DSI); > + if (ret) { > + dev_err(dsi->dev, > + "Couldn't initialise the DSI connector\n"); > + goto err_cleanup_connector; > + } > + > + drm_connector_attach_encoder(&dsi->connector, &dsi->encoder); > + drm_panel_attach(dsi->panel, &dsi->connector); > } > > - drm_connector_attach_encoder(&dsi->connector, &dsi->encoder); > - drm_panel_attach(dsi->panel, &dsi->connector); > + if (dsi->bridge) { > + ret = drm_bridge_attach(&dsi->encoder, dsi->bridge, NULL); > + if (ret) { > + dev_err(dsi->dev, "Couldn't attach the DSI bridge\n"); > + goto err_cleanup_connector; > + } > + } > > return 0; > > @@ -1104,7 +1130,12 @@ static void sun6i_dsi_unbind(struct device *dev, struct device *master, > { > struct sun6i_dsi *dsi = dev_get_drvdata(dev); > > - drm_panel_detach(dsi->panel); > + if (dsi->panel) > + drm_panel_detach(dsi->panel); > + > + if (dsi->bridge) > + drm_bridge_detach(dsi->bridge); As I mentionned in the first patch, this is quite suspicious since the DRM core should be in charge of detaching the bridge, not the driver. Cheers, Paul > + > } > > static const struct component_ops sun6i_dsi_ops = { > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h > index 5c4983212f89..76874ff8e3ef 100644 > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h > @@ -36,6 +36,7 @@ struct sun6i_dsi { > struct sun4i_tcon *tcon; > struct mipi_dsi_device *device; > struct drm_panel *panel; > + struct drm_bridge *bridge; > const struct sun6i_dsi_variant *variant; > }; > > -- > 2.18.0.321.gffc6fa0e3 >
On Fri, Mar 15, 2019 at 02:32:55PM +0100, Paul Kocialkowski wrote: > Hi, > > On Fri, 2019-03-15 at 18:38 +0530, Jagan Teki wrote: > > Some display panels would come up with a non-DSI output which > > can have an option to connect DSI interface by means of bridge > > convertor. > > > > This DSI to non-DSI bridge convertor would require a bridge > > driver that would communicate the DSI controller for bridge > > functionalities. > > > > So, add support for bridge functionalities in Allwinner DSI > > controller. > > See a few comments below. > > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> > > --- > > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 65 +++++++++++++++++++------- > > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h | 1 + > > 2 files changed, 49 insertions(+), 17 deletions(-) > > > > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > > index 0960b96b62cc..64d74313b842 100644 > > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > > @@ -781,6 +781,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) > > if (!IS_ERR(dsi->panel)) > > drm_panel_prepare(dsi->panel); > > > > + if (!IS_ERR(dsi->bridge)) > > + drm_bridge_pre_enable(dsi->bridge); > > + > > /* > > * FIXME: This should be moved after the switch to HS mode. > > * > > @@ -796,6 +799,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) > > if (!IS_ERR(dsi->panel)) > > drm_panel_enable(dsi->panel); > > > > + if (!IS_ERR(dsi->bridge)) > > + drm_bridge_enable(dsi->bridge); > > + > > sun6i_dsi_start(dsi, DSI_START_HSC); > > > > udelay(1000); > > @@ -812,6 +818,9 @@ static void sun6i_dsi_encoder_disable(struct drm_encoder *encoder) > > if (!IS_ERR(dsi->panel)) { > > drm_panel_disable(dsi->panel); > > drm_panel_unprepare(dsi->panel); > > + } else if (!IS_ERR(dsi->bridge)) { > > + drm_bridge_disable(dsi->bridge); > > + drm_bridge_post_disable(dsi->bridge); > > } > > > > phy_power_off(dsi->dphy); > > @@ -973,11 +982,16 @@ static int sun6i_dsi_attach(struct mipi_dsi_host *host, > > struct sun6i_dsi *dsi = host_to_sun6i_dsi(host); > > > > dsi->device = device; > > - dsi->panel = of_drm_find_panel(device->dev.of_node); > > - if (IS_ERR(dsi->panel)) > > - return PTR_ERR(dsi->panel); > > > > - dev_info(host->dev, "Attached device %s\n", device->name); > > + dsi->bridge = of_drm_find_bridge(device->dev.of_node); > > + if (!dsi->bridge) { > > You are using IS_ERR to check that the bridge is alive in the changes > above, but switch to checking that it's non-NULL at this point. > > Are both guaranteed to be interchangeable? They aren't. Any ERR_PTR will be !NULL > > + dsi->panel = of_drm_find_panel(device->dev.of_node); > > + if (IS_ERR(dsi->panel)) > > + return PTR_ERR(dsi->panel); > > + } > > You should probably use drm_of_find_panel_or_bridge instead of > duplicating the logic here. Or we can even use the drm_panel_bridge_add to simplify things. Maxime
Hi, On Fri, 2019-03-15 at 14:45 +0100, Maxime Ripard wrote: > On Fri, Mar 15, 2019 at 02:32:55PM +0100, Paul Kocialkowski wrote: > > Hi, > > > > On Fri, 2019-03-15 at 18:38 +0530, Jagan Teki wrote: > > > Some display panels would come up with a non-DSI output which > > > can have an option to connect DSI interface by means of bridge > > > convertor. > > > > > > This DSI to non-DSI bridge convertor would require a bridge > > > driver that would communicate the DSI controller for bridge > > > functionalities. > > > > > > So, add support for bridge functionalities in Allwinner DSI > > > controller. > > > > See a few comments below. > > > > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> > > > --- > > > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 65 +++++++++++++++++++------- > > > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h | 1 + > > > 2 files changed, 49 insertions(+), 17 deletions(-) > > > > > > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > > > index 0960b96b62cc..64d74313b842 100644 > > > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > > > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > > > @@ -781,6 +781,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) > > > if (!IS_ERR(dsi->panel)) > > > drm_panel_prepare(dsi->panel); > > > > > > + if (!IS_ERR(dsi->bridge)) > > > + drm_bridge_pre_enable(dsi->bridge); > > > + > > > /* > > > * FIXME: This should be moved after the switch to HS mode. > > > * > > > @@ -796,6 +799,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) > > > if (!IS_ERR(dsi->panel)) > > > drm_panel_enable(dsi->panel); > > > > > > + if (!IS_ERR(dsi->bridge)) > > > + drm_bridge_enable(dsi->bridge); > > > + > > > sun6i_dsi_start(dsi, DSI_START_HSC); > > > > > > udelay(1000); > > > @@ -812,6 +818,9 @@ static void sun6i_dsi_encoder_disable(struct drm_encoder *encoder) > > > if (!IS_ERR(dsi->panel)) { > > > drm_panel_disable(dsi->panel); > > > drm_panel_unprepare(dsi->panel); > > > + } else if (!IS_ERR(dsi->bridge)) { > > > + drm_bridge_disable(dsi->bridge); > > > + drm_bridge_post_disable(dsi->bridge); > > > } > > > > > > phy_power_off(dsi->dphy); > > > @@ -973,11 +982,16 @@ static int sun6i_dsi_attach(struct mipi_dsi_host *host, > > > struct sun6i_dsi *dsi = host_to_sun6i_dsi(host); > > > > > > dsi->device = device; > > > - dsi->panel = of_drm_find_panel(device->dev.of_node); > > > - if (IS_ERR(dsi->panel)) > > > - return PTR_ERR(dsi->panel); > > > > > > - dev_info(host->dev, "Attached device %s\n", device->name); > > > + dsi->bridge = of_drm_find_bridge(device->dev.of_node); > > > + if (!dsi->bridge) { > > > > You are using IS_ERR to check that the bridge is alive in the changes > > above, but switch to checking that it's non-NULL at this point. > > > > Are both guaranteed to be interchangeable? > > They aren't. Any ERR_PTR will be !NULL > > > > + dsi->panel = of_drm_find_panel(device->dev.of_node); > > > + if (IS_ERR(dsi->panel)) > > > + return PTR_ERR(dsi->panel); > > > + } > > > > You should probably use drm_of_find_panel_or_bridge instead of > > duplicating the logic here. > > Or we can even use the drm_panel_bridge_add to simplify things. Indeed, I was just looking at that and it seems to be specifically tailored for this use case. Cheers, Paul
Hi Paul and Maxime, On Fri, Mar 15, 2019 at 7:03 PM Paul Kocialkowski <paul.kocialkowski@bootlin.com> wrote: > > Hi, > > On Fri, 2019-03-15 at 18:38 +0530, Jagan Teki wrote: > > Some display panels would come up with a non-DSI output which > > can have an option to connect DSI interface by means of bridge > > convertor. > > > > This DSI to non-DSI bridge convertor would require a bridge > > driver that would communicate the DSI controller for bridge > > functionalities. > > > > So, add support for bridge functionalities in Allwinner DSI > > controller. > > See a few comments below. > > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> > > --- > > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 65 +++++++++++++++++++------- > > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h | 1 + > > 2 files changed, 49 insertions(+), 17 deletions(-) > > > > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > > index 0960b96b62cc..64d74313b842 100644 > > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c > > @@ -781,6 +781,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) > > if (!IS_ERR(dsi->panel)) > > drm_panel_prepare(dsi->panel); > > > > + if (!IS_ERR(dsi->bridge)) > > + drm_bridge_pre_enable(dsi->bridge); > > + > > /* > > * FIXME: This should be moved after the switch to HS mode. > > * > > @@ -796,6 +799,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) > > if (!IS_ERR(dsi->panel)) > > drm_panel_enable(dsi->panel); > > > > + if (!IS_ERR(dsi->bridge)) > > + drm_bridge_enable(dsi->bridge); > > + > > sun6i_dsi_start(dsi, DSI_START_HSC); > > > > udelay(1000); > > @@ -812,6 +818,9 @@ static void sun6i_dsi_encoder_disable(struct drm_encoder *encoder) > > if (!IS_ERR(dsi->panel)) { > > drm_panel_disable(dsi->panel); > > drm_panel_unprepare(dsi->panel); > > + } else if (!IS_ERR(dsi->bridge)) { > > + drm_bridge_disable(dsi->bridge); > > + drm_bridge_post_disable(dsi->bridge); > > } > > > > phy_power_off(dsi->dphy); > > @@ -973,11 +982,16 @@ static int sun6i_dsi_attach(struct mipi_dsi_host *host, > > struct sun6i_dsi *dsi = host_to_sun6i_dsi(host); > > > > dsi->device = device; > > - dsi->panel = of_drm_find_panel(device->dev.of_node); > > - if (IS_ERR(dsi->panel)) > > - return PTR_ERR(dsi->panel); > > > > - dev_info(host->dev, "Attached device %s\n", device->name); > > + dsi->bridge = of_drm_find_bridge(device->dev.of_node); > > + if (!dsi->bridge) { > > You are using IS_ERR to check that the bridge is alive in the changes > above, but switch to checking that it's non-NULL at this point. > > Are both guaranteed to be interchangeable? > > > + dsi->panel = of_drm_find_panel(device->dev.of_node); > > + if (IS_ERR(dsi->panel)) > > + return PTR_ERR(dsi->panel); > > + } > > You should probably use drm_of_find_panel_or_bridge instead of > duplicating the logic here. True, In-fact I did try this API. but pipeline were unable to bound. Usually the panel and bridge were attached first and then the pipeline bound would start from front-end (in A33) But in my below cases I have seen only panel or bridge attached but no pipeline bound at all. And I'm using drm_of_find_panel_or_bridge(host->dev->of_node, 1, 0, &dsi->panel, &dsi->bridge); in dsi attach API. Case-1, panel: &dsi { vcc-dsi-supply = <®_dcdc1>; /* VCC3V3-DSI */ status = "okay"; ports { dsi_out: port@1 { reg = <1>; dsi_out_panel: endpoint { remote-endpoint = <&panel_out_dsi>; }; }; }; panel@0 { compatible = "bananapi,s070wv20-ct16-icn6211"; reg = <0>; enable-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* LCD-PWR-EN: PB7 */ reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */ backlight = <&backlight>; port { panel_out_dsi: endpoint { remote-endpoint = <&dsi_out_panel>; }; }; }; }; Case-2, bridge: panel { compatible = "bananapi,s070wv20-ct16", "simple-panel"; enable-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* LCD-PWR-EN: PB7 */ backlight = <&backlight>; port { panel_out_bridge: endpoint { remote-endpoint = <&bridge_out_panel>; }; }; }; &dsi { vcc-dsi-supply = <®_dcdc1>; /* VCC-DSI */ status = "okay"; ports { dsi_out: port@1 { reg = <1>; dsi_out_bridge: endpoint { remote-endpoint = <&bridge_out_dsi>; }; }; }; bridge@0 { reg = <0>; compatible = "bananapi,icn6211", "chipone,icn6211"; reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */ #address-cells = <1>; #size-cells = <0>; ports { #address-cells = <1>; #size-cells = <0>; bridge_in: port@0 { reg = <0>; bridge_out_dsi: endpoint { remote-endpoint = <&dsi_out_bridge>; }; }; bridge_out: port@1 { reg = <1>; bridge_out_panel: endpoint { remote-endpoint = <&panel_out_bridge>; }; }; }; }; }; I think, I'm sure about the pipeline connections as per my understanding. but something loosely missed here or in the code. Please do let me know for any suggestions. Jagan.
diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c index 0960b96b62cc..64d74313b842 100644 --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c @@ -781,6 +781,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) if (!IS_ERR(dsi->panel)) drm_panel_prepare(dsi->panel); + if (!IS_ERR(dsi->bridge)) + drm_bridge_pre_enable(dsi->bridge); + /* * FIXME: This should be moved after the switch to HS mode. * @@ -796,6 +799,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) if (!IS_ERR(dsi->panel)) drm_panel_enable(dsi->panel); + if (!IS_ERR(dsi->bridge)) + drm_bridge_enable(dsi->bridge); + sun6i_dsi_start(dsi, DSI_START_HSC); udelay(1000); @@ -812,6 +818,9 @@ static void sun6i_dsi_encoder_disable(struct drm_encoder *encoder) if (!IS_ERR(dsi->panel)) { drm_panel_disable(dsi->panel); drm_panel_unprepare(dsi->panel); + } else if (!IS_ERR(dsi->bridge)) { + drm_bridge_disable(dsi->bridge); + drm_bridge_post_disable(dsi->bridge); } phy_power_off(dsi->dphy); @@ -973,11 +982,16 @@ static int sun6i_dsi_attach(struct mipi_dsi_host *host, struct sun6i_dsi *dsi = host_to_sun6i_dsi(host); dsi->device = device; - dsi->panel = of_drm_find_panel(device->dev.of_node); - if (IS_ERR(dsi->panel)) - return PTR_ERR(dsi->panel); - dev_info(host->dev, "Attached device %s\n", device->name); + dsi->bridge = of_drm_find_bridge(device->dev.of_node); + if (!dsi->bridge) { + dsi->panel = of_drm_find_panel(device->dev.of_node); + if (IS_ERR(dsi->panel)) + return PTR_ERR(dsi->panel); + } + + dev_info(host->dev, "Attached %s %s\n", + dsi->bridge ? "bridge" : "panel", device->name); return 0; } @@ -1055,8 +1069,10 @@ static int sun6i_dsi_bind(struct device *dev, struct device *master, struct sun4i_tcon *tcon0 = sun4i_get_tcon0(drm); int ret; - if (!dsi->panel) + if (!(dsi->panel || dsi->bridge)) { + dev_info(drm->dev, "No panel or bridge found... DSI output disabled\n"); return -EPROBE_DEFER; + } dsi->drv = drv; @@ -1078,19 +1094,29 @@ static int sun6i_dsi_bind(struct device *dev, struct device *master, } dsi->encoder.possible_crtcs = BIT(0); - drm_connector_helper_add(&dsi->connector, - &sun6i_dsi_connector_helper_funcs); - ret = drm_connector_init(drm, &dsi->connector, - &sun6i_dsi_connector_funcs, - DRM_MODE_CONNECTOR_DSI); - if (ret) { - dev_err(dsi->dev, - "Couldn't initialise the DSI connector\n"); - goto err_cleanup_connector; + if (dsi->panel) { + drm_connector_helper_add(&dsi->connector, + &sun6i_dsi_connector_helper_funcs); + ret = drm_connector_init(drm, &dsi->connector, + &sun6i_dsi_connector_funcs, + DRM_MODE_CONNECTOR_DSI); + if (ret) { + dev_err(dsi->dev, + "Couldn't initialise the DSI connector\n"); + goto err_cleanup_connector; + } + + drm_connector_attach_encoder(&dsi->connector, &dsi->encoder); + drm_panel_attach(dsi->panel, &dsi->connector); } - drm_connector_attach_encoder(&dsi->connector, &dsi->encoder); - drm_panel_attach(dsi->panel, &dsi->connector); + if (dsi->bridge) { + ret = drm_bridge_attach(&dsi->encoder, dsi->bridge, NULL); + if (ret) { + dev_err(dsi->dev, "Couldn't attach the DSI bridge\n"); + goto err_cleanup_connector; + } + } return 0; @@ -1104,7 +1130,12 @@ static void sun6i_dsi_unbind(struct device *dev, struct device *master, { struct sun6i_dsi *dsi = dev_get_drvdata(dev); - drm_panel_detach(dsi->panel); + if (dsi->panel) + drm_panel_detach(dsi->panel); + + if (dsi->bridge) + drm_bridge_detach(dsi->bridge); + } static const struct component_ops sun6i_dsi_ops = { diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h index 5c4983212f89..76874ff8e3ef 100644 --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h @@ -36,6 +36,7 @@ struct sun6i_dsi { struct sun4i_tcon *tcon; struct mipi_dsi_device *device; struct drm_panel *panel; + struct drm_bridge *bridge; const struct sun6i_dsi_variant *variant; };
Some display panels would come up with a non-DSI output which can have an option to connect DSI interface by means of bridge convertor. This DSI to non-DSI bridge convertor would require a bridge driver that would communicate the DSI controller for bridge functionalities. So, add support for bridge functionalities in Allwinner DSI controller. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 65 +++++++++++++++++++------- drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h | 1 + 2 files changed, 49 insertions(+), 17 deletions(-)