diff mbox series

[v3,9/9] ARM: dts: sun8i: a83t: Enable USB OTG controller on some boards

Message ID 20190321084850.20769-10-wens@kernel.org (mailing list archive)
State Superseded, archived
Headers show
Series ARM: sun8i: a83t: Enable USB OTG | expand

Commit Message

Chen-Yu Tsai March 21, 2019, 8:48 a.m. UTC 
From: Chen-Yu Tsai <wens@csie.org>

The Bananapi M3 and Cubietruck Plus both have USB OTG ports wired to the
SoC and PMIC in the same way, with the N_VBUSEN pin on the PMIC
controlling VBUS output, the PMIC's VBUS input for sensing VBUS, and
PH11 on the SoC for sensing the ID pin.

Enable OTG on both boards.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts     | 12 ++++++++++++
 arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts | 12 ++++++++++++
 2 files changed, 24 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
index 838be7b3715f..9d34eabba121 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
@@ -389,7 +389,19 @@ 
 	};
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
 &usbphy {
+	usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
index fcbec3d7ccd7..ea299d3d84d0 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
@@ -420,7 +420,19 @@ 
 	};
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
 &usbphy {
+	usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";