diff mbox series

[v2,06/13] pinctrl: sunxi: Support I/O bias voltage setting on H6

Message ID 20190409002452.14551-7-megous@megous.com (mailing list archive)
State New, archived
Headers show
Series Add support for Orange Pi 3 | expand

Commit Message

Ondřej Jirman April 9, 2019, 12:24 a.m. UTC 
From: Ondrej Jirman <megous@megous.com>

H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.

Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).

This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:

  commit 402bfb3c1352 ("Support I/O bias voltage setting on A80")

Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c |  1 +
 drivers/pinctrl/sunxi/pinctrl-sunxi.c     | 10 ++++++++++
 drivers/pinctrl/sunxi/pinctrl-sunxi.h     |  4 ++++
 3 files changed, 15 insertions(+)
diff mbox series

Patch

diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c
index ef4268cc6227..30b1befa8ed8 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c
@@ -591,6 +591,7 @@  static const struct sunxi_pinctrl_desc h6_pinctrl_data = {
 	.irq_banks = 4,
 	.irq_bank_map = h6_irq_bank_map,
 	.irq_read_needs_mux = true,
+	.io_bias_cfg_variant = IO_BIAS_CFG_V2,
 };
 
 static int h6_pinctrl_probe(struct platform_device *pdev)
diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.c b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
index b8dd58ef33b7..0ab50a15a716 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sunxi.c
+++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
@@ -607,6 +607,8 @@  static int sunxi_pinctrl_set_io_bias_cfg(struct sunxi_pinctrl *pctl,
 					 unsigned pin,
 					 struct regulator *supply)
 {
+	unsigned short bank = pin / PINS_PER_BANK;
+	unsigned long flags;
 	u32 val, reg;
 	int uV;
 
@@ -642,6 +644,14 @@  static int sunxi_pinctrl_set_io_bias_cfg(struct sunxi_pinctrl *pctl,
 		reg = readl(pctl->membase + sunxi_grp_config_reg(pin));
 		reg &= ~IO_BIAS_MASK;
 		writel(reg | val, pctl->membase + sunxi_grp_config_reg(pin));
+	} else if (pctl->desc->io_bias_cfg_variant == IO_BIAS_CFG_V2) {
+		val = uV <= 1800000 ? 1 : 0;
+
+		raw_spin_lock_irqsave(&pctl->lock, flags);
+		reg = readl(pctl->membase + PIO_POW_MOD_SEL_REG);
+		reg &= ~(1 << bank);
+		writel(reg | val << bank, pctl->membase + PIO_POW_MOD_SEL_REG);
+		raw_spin_unlock_irqrestore(&pctl->lock, flags);
 	}
 
 	return 0;
diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.h b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
index 642f667e99d2..4044a3cb1819 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sunxi.h
+++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
@@ -95,8 +95,12 @@ 
 #define PINCTRL_SUN7I_A20	BIT(7)
 #define PINCTRL_SUN8I_R40	BIT(8)
 
+#define PIO_POW_MOD_SEL_REG	0x340
+
 /* Bias voltage configuration done via Pn_GRP_CONFIG registers. */
 #define IO_BIAS_CFG_V1		1
+/* Bias voltage set in the PIO_POW_MOD_SEL_REG register. */
+#define IO_BIAS_CFG_V2		2
 
 struct sunxi_desc_function {
 	unsigned long	variant;