@@ -602,6 +602,7 @@ dtb-$(CONFIG_SOC_IMX7ULP) += \
dtb-$(CONFIG_SOC_LS1021A) += \
ls1021a-moxa-uc-8410a.dtb \
ls1021a-qds.dtb \
+ ls1021a-tsn.dtb \
ls1021a-twr.dtb
dtb-$(CONFIG_SOC_VF610) += \
vf500-colibri-eval-v3.dtb \
new file mode 100644
@@ -0,0 +1,289 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright 2016-2018 NXP Semiconductors
+ * Copyright 2019 Vladimir Oltean <olteanv@gmail.com>
+ */
+
+/dts-v1/;
+#include "ls1021a.dtsi"
+
+/ {
+ model = "NXP LS1021A-TSN Board";
+
+ sys_mclk: clock-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+
+ reg_vdda_codec: regulator-3V3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vddio_codec: regulator-2V5 {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+};
+
+&dspi0 {
+ bus-num = <0>;
+ status = "okay";
+
+ /* ADG704BRMZ 1:4 SPI mux/demux */
+ sja1105: ethernet-switch@1 {
+ reg = <0x1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "nxp,sja1105t";
+ /* 12 MHz */
+ spi-max-frequency = <12000000>;
+ /* Sample data on trailing clock edge */
+ spi-cpha;
+ /* SPI controller settings for SJA1105 timing requirements */
+ fsl,spi-cs-sck-delay = <1000>;
+ fsl,spi-sck-cs-delay = <1000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ /* ETH5 written on chassis */
+ label = "swp5";
+ phy-handle = <&rgmii_phy6>;
+ phy-mode = "rgmii-id";
+ reg = <0>;
+ };
+
+ port@1 {
+ /* ETH2 written on chassis */
+ label = "swp2";
+ phy-handle = <&rgmii_phy3>;
+ phy-mode = "rgmii-id";
+ reg = <1>;
+ };
+
+ port@2 {
+ /* ETH3 written on chassis */
+ label = "swp3";
+ phy-handle = <&rgmii_phy4>;
+ phy-mode = "rgmii-id";
+ reg = <2>;
+ };
+
+ port@3 {
+ /* ETH4 written on chassis */
+ label = "swp4";
+ phy-handle = <&rgmii_phy5>;
+ phy-mode = "rgmii-id";
+ reg = <3>;
+ };
+
+ port@4 {
+ /* Internal port connected to eth2 */
+ ethernet = <&enet2>;
+ phy-mode = "rgmii";
+ reg = <4>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+};
+
+&enet0 {
+ tbi-handle = <&tbi0>;
+ phy-handle = <&sgmii_phy2>;
+ phy-mode = "sgmii";
+ status = "okay";
+};
+
+&enet1 {
+ tbi-handle = <&tbi1>;
+ phy-handle = <&sgmii_phy1>;
+ phy-mode = "sgmii";
+ status = "okay";
+};
+
+/* RGMII delays added via PCB traces */
+&enet2 {
+ phy-mode = "rgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&esdhc {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ /* 3 axis accelerometer */
+ accelerometer@1e {
+ compatible = "fsl,fxls8471";
+ position = <0>;
+ reg = <0x1e>;
+ };
+
+ /* Audio codec (SAI2) */
+ audio-codec@2a {
+ compatible = "fsl,sgtl5000";
+ VDDIO-supply = <®_vddio_codec>;
+ VDDA-supply = <®_vdda_codec>;
+ #sound-dai-cells = <0>;
+ clocks = <&sys_mclk>;
+ reg = <0x2a>;
+ };
+
+ /* Current sensing circuit for 1V VDDCORE PMIC rail */
+ current-sensor@44 {
+ compatible = "ti,ina220";
+ shunt-resistor = <1000>;
+ reg = <0x44>;
+ };
+
+ /* Current sensing circuit for 12V VCC rail */
+ current-sensor@45 {
+ compatible = "ti,ina220";
+ shunt-resistor = <1000>;
+ reg = <0x45>;
+ };
+
+ /* Thermal monitor - case */
+ temperature-sensor@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+
+ /* Thermal monitor - chip */
+ temperature-sensor@4c {
+ compatible = "ti,tmp451";
+ reg = <0x4c>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c32";
+ reg = <0x51>;
+ };
+
+ /* Unsupported devices:
+ * - FXAS21002C Gyroscope at 0x20
+ * - TI ADS7924 4-channel ADC at 0x49
+ */
+};
+
+&ifc {
+ status = "disabled";
+};
+
+&lpuart0 {
+ status = "okay";
+};
+
+&lpuart3 {
+ status = "okay";
+};
+
+&mdio0 {
+ /* AR8031 */
+ sgmii_phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ };
+
+ /* AR8031 */
+ sgmii_phy2: ethernet-phy@2 {
+ reg = <0x2>;
+ };
+
+ /* BCM5464 quad PHY */
+ rgmii_phy3: ethernet-phy@3 {
+ reg = <0x3>;
+ };
+
+ rgmii_phy4: ethernet-phy@4 {
+ reg = <0x4>;
+ };
+
+ rgmii_phy5: ethernet-phy@5 {
+ reg = <0x5>;
+ };
+
+ rgmii_phy6: ethernet-phy@6 {
+ reg = <0x6>;
+ };
+
+ /* SGMII PCS for enet0 */
+ tbi0: tbi-phy@1f {
+ reg = <0x1f>;
+ device_type = "tbi-phy";
+ };
+};
+
+&mdio1 {
+ /* SGMII PCS for enet1 */
+ tbi1: tbi-phy@1f {
+ reg = <0x1f>;
+ device_type = "tbi-phy";
+ };
+};
+
+&qspi {
+ status = "okay";
+
+ flash@0 {
+ /* Rev. A uses 64MB flash, Rev. B & C use 32MB flash */
+ compatible = "jedec,spi-nor", "s25fl256s1", "s25fl512s";
+ spi-max-frequency = <20000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "RCW";
+ reg = <0x0 0x40000>;
+ };
+
+ partition@40000 {
+ label = "U-Boot";
+ reg = <0x40000 0x300000>;
+ };
+
+ partition@340000 {
+ label = "U-Boot Env";
+ reg = <0x340000 0x100000>;
+ };
+ };
+ };
+};
+
+&sai2 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
The LS1021A-TSN is a development board built by VVDN/Argonboards in partnership with NXP. It features the LS1021A SoC and the first-generation SJA1105T Ethernet switch for prototyping implementations of a subset of IEEE 802.1 TSN standards. It has two regular Ethernet ports and four switched, TSN-capable ports. It also features: - One Arduino header - One expansion header - Two USB 3.0 ports - One mini PCIe slot - One SATA interface - Accelerometer, gyroscope, temperature sensors Signed-off-by: Vladimir Oltean <olteanv@gmail.com> --- Changes from v3: - Not all nodes were alphabetically sorted ("d->i->e" vs "d->e->i") Changes from v2: - Sorted nodes alphabetically - Renamed SAI2 codec node into audio-codec v2 patch available at: https://lkml.org/lkml/2019/5/29/998 Changes from v1: - Applied Shawn's feedback - Introduced QSPI flash node v1 patch available at: https://patchwork.kernel.org/patch/10930451/ arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/ls1021a-tsn.dts | 289 ++++++++++++++++++++++++++++++ 2 files changed, 290 insertions(+) create mode 100644 arch/arm/boot/dts/ls1021a-tsn.dts