diff mbox series

[v2,2/4] ARM: dts: meson: switch to the generic Ethernet PHY reset bindings

Message ID 20190612205529.19834-3-martin.blumenstingl@googlemail.com (mailing list archive)
State New, archived
Headers show
Series Ethernet PHY reset GPIO updates for Amlogic SoCs | expand

Commit Message

Martin Blumenstingl June 12, 2019, 8:55 p.m. UTC
The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.

Replace snps,reset-gpio from the &ethmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.

snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.
Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- RTL8211F PHY on the Odroid-C1 and MXIII-Plus needs a 10ms assert
  delay (the datasheet mentions: "For a complete PHY reset, this pin
  must be asserted low for at least 10ms") and a 30ms deassert delay
  (the datasheet mentions: "Wait for a further 30ms (for internal
  circuits settling time) before accessing the PHY register"). The
  old settings used 10ms for assert and 1000ms for deassert.
- IP101GR PHY on the EC-100 and MXQ needs a 10ms assert delay (the
  datasheet mentions: "Trst | Reset period | 10ms") and a 10ms deassert
  delay as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
  output ready after reset released | 10ms")). The old settings used
  10ms for assert and 1000ms for deassert.

No functional changes intended.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 arch/arm/boot/dts/meson8b-ec100.dts       | 9 +++++----
 arch/arm/boot/dts/meson8b-mxq.dts         | 9 +++++----
 arch/arm/boot/dts/meson8b-odroidc1.dts    | 9 +++++----
 arch/arm/boot/dts/meson8m2-mxiii-plus.dts | 8 ++++----
 4 files changed, 19 insertions(+), 16 deletions(-)

Comments

Neil Armstrong June 14, 2019, 9:02 a.m. UTC | #1
On 12/06/2019 22:55, Martin Blumenstingl wrote:
> The snps,reset-gpio bindings are deprecated in favour of the generic
> "Ethernet PHY reset" bindings.
> 
> Replace snps,reset-gpio from the &ethmac node with reset-gpios in the
> ethernet-phy node. The old snps,reset-active-low property is now encoded
> directly as GPIO flag inside the reset-gpios property.
> 
> snps,reset-delays-us is converted to reset-assert-us and
> reset-deassert-us. reset-assert-us is the second cell from
> snps,reset-delays-us while reset-deassert-us was the third cell.
> Instead of blindly copying the old values (which seems strange since
> they gave the PHY one second to come out of reset) over this also
> updates the delays based on the datasheets:
> - RTL8211F PHY on the Odroid-C1 and MXIII-Plus needs a 10ms assert
>   delay (the datasheet mentions: "For a complete PHY reset, this pin
>   must be asserted low for at least 10ms") and a 30ms deassert delay
>   (the datasheet mentions: "Wait for a further 30ms (for internal
>   circuits settling time) before accessing the PHY register"). The
>   old settings used 10ms for assert and 1000ms for deassert.
> - IP101GR PHY on the EC-100 and MXQ needs a 10ms assert delay (the
>   datasheet mentions: "Trst | Reset period | 10ms") and a 10ms deassert
>   delay as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
>   output ready after reset released | 10ms")). The old settings used
>   10ms for assert and 1000ms for deassert.
> 
> No functional changes intended.
> 
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> ---
>  arch/arm/boot/dts/meson8b-ec100.dts       | 9 +++++----
>  arch/arm/boot/dts/meson8b-mxq.dts         | 9 +++++----
>  arch/arm/boot/dts/meson8b-odroidc1.dts    | 9 +++++----
>  arch/arm/boot/dts/meson8m2-mxiii-plus.dts | 8 ++++----
>  4 files changed, 19 insertions(+), 16 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/meson8b-ec100.dts b/arch/arm/boot/dts/meson8b-ec100.dts
> index 9bf4249cb60d..96d239d8334e 100644
> --- a/arch/arm/boot/dts/meson8b-ec100.dts
> +++ b/arch/arm/boot/dts/meson8b-ec100.dts
> @@ -234,10 +234,6 @@
>  	phy-handle = <&eth_phy0>;
>  	phy-mode = "rmii";
>  
> -	snps,reset-gpio = <&gpio GPIOH_4 0>;
> -	snps,reset-delays-us = <0 10000 1000000>;
> -	snps,reset-active-low;
> -
>  	mdio {
>  		compatible = "snps,dwmac-mdio";
>  		#address-cells = <1>;
> @@ -246,6 +242,11 @@
>  		eth_phy0: ethernet-phy@0 {
>  			/* IC Plus IP101A/G (0x02430c54) */
>  			reg = <0>;
> +
> +			reset-assert-us = <10000>;
> +			reset-deassert-us = <10000>;
> +			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
> +
>  			icplus,select-interrupt;
>  			interrupt-parent = <&gpio_intc>;
>  			/* GPIOH_3 */
> diff --git a/arch/arm/boot/dts/meson8b-mxq.dts b/arch/arm/boot/dts/meson8b-mxq.dts
> index ef602ab45efd..bb27b34eb346 100644
> --- a/arch/arm/boot/dts/meson8b-mxq.dts
> +++ b/arch/arm/boot/dts/meson8b-mxq.dts
> @@ -91,10 +91,6 @@
>  	phy-handle = <&eth_phy0>;
>  	phy-mode = "rmii";
>  
> -	snps,reset-gpio = <&gpio GPIOH_4 0>;
> -	snps,reset-delays-us = <0 10000 1000000>;
> -	snps,reset-active-low;
> -
>  	mdio {
>  		compatible = "snps,dwmac-mdio";
>  		#address-cells = <1>;
> @@ -103,6 +99,11 @@
>  		eth_phy0: ethernet-phy@0 {
>  			/* IC Plus IP101A/G (0x02430c54) */
>  			reg = <0>;
> +
> +			reset-assert-us = <10000>;
> +			reset-deassert-us = <10000>;
> +			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
> +
>  			icplus,select-interrupt;
>  			interrupt-parent = <&gpio_intc>;
>  			/* GPIOH_3 */
> diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
> index 018695b2b83a..86c4614e0a38 100644
> --- a/arch/arm/boot/dts/meson8b-odroidc1.dts
> +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
> @@ -176,10 +176,6 @@
>  &ethmac {
>  	status = "okay";
>  
> -	snps,reset-gpio = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>;
> -	snps,reset-active-low;
> -	snps,reset-delays-us = <0 10000 30000>;
> -
>  	pinctrl-0 = <&eth_rgmii_pins>;
>  	pinctrl-names = "default";
>  
> @@ -195,6 +191,11 @@
>  		/* Realtek RTL8211F (0x001cc916) */
>  		eth_phy: ethernet-phy@0 {
>  			reg = <0>;
> +
> +			reset-assert-us = <10000>;
> +			reset-deassert-us = <30000>;
> +			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
> +
>  			interrupt-parent = <&gpio_intc>;
>  			/* GPIOH_3 */
>  			interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
> diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
> index 59b07a55e461..d54477b1001c 100644
> --- a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
> +++ b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
> @@ -73,10 +73,6 @@
>  
>  	amlogic,tx-delay-ns = <4>;
>  
> -	snps,reset-gpio = <&gpio GPIOH_4 0>;
> -	snps,reset-delays-us = <0 10000 1000000>;
> -	snps,reset-active-low;
> -
>  	mdio {
>  		compatible = "snps,dwmac-mdio";
>  		#address-cells = <1>;
> @@ -85,6 +81,10 @@
>  		eth_phy0: ethernet-phy@0 {
>  			/* Realtek RTL8211F (0x001cc916) */
>  			reg = <0>;
> +
> +			reset-assert-us = <10000>;
> +			reset-deassert-us = <30000>;
> +			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
>  		};
>  	};
>  };
> 

Nice !

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/meson8b-ec100.dts b/arch/arm/boot/dts/meson8b-ec100.dts
index 9bf4249cb60d..96d239d8334e 100644
--- a/arch/arm/boot/dts/meson8b-ec100.dts
+++ b/arch/arm/boot/dts/meson8b-ec100.dts
@@ -234,10 +234,6 @@ 
 	phy-handle = <&eth_phy0>;
 	phy-mode = "rmii";
 
-	snps,reset-gpio = <&gpio GPIOH_4 0>;
-	snps,reset-delays-us = <0 10000 1000000>;
-	snps,reset-active-low;
-
 	mdio {
 		compatible = "snps,dwmac-mdio";
 		#address-cells = <1>;
@@ -246,6 +242,11 @@ 
 		eth_phy0: ethernet-phy@0 {
 			/* IC Plus IP101A/G (0x02430c54) */
 			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+
 			icplus,select-interrupt;
 			interrupt-parent = <&gpio_intc>;
 			/* GPIOH_3 */
diff --git a/arch/arm/boot/dts/meson8b-mxq.dts b/arch/arm/boot/dts/meson8b-mxq.dts
index ef602ab45efd..bb27b34eb346 100644
--- a/arch/arm/boot/dts/meson8b-mxq.dts
+++ b/arch/arm/boot/dts/meson8b-mxq.dts
@@ -91,10 +91,6 @@ 
 	phy-handle = <&eth_phy0>;
 	phy-mode = "rmii";
 
-	snps,reset-gpio = <&gpio GPIOH_4 0>;
-	snps,reset-delays-us = <0 10000 1000000>;
-	snps,reset-active-low;
-
 	mdio {
 		compatible = "snps,dwmac-mdio";
 		#address-cells = <1>;
@@ -103,6 +99,11 @@ 
 		eth_phy0: ethernet-phy@0 {
 			/* IC Plus IP101A/G (0x02430c54) */
 			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+
 			icplus,select-interrupt;
 			interrupt-parent = <&gpio_intc>;
 			/* GPIOH_3 */
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index 018695b2b83a..86c4614e0a38 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -176,10 +176,6 @@ 
 &ethmac {
 	status = "okay";
 
-	snps,reset-gpio = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>;
-	snps,reset-active-low;
-	snps,reset-delays-us = <0 10000 30000>;
-
 	pinctrl-0 = <&eth_rgmii_pins>;
 	pinctrl-names = "default";
 
@@ -195,6 +191,11 @@ 
 		/* Realtek RTL8211F (0x001cc916) */
 		eth_phy: ethernet-phy@0 {
 			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <30000>;
+			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+
 			interrupt-parent = <&gpio_intc>;
 			/* GPIOH_3 */
 			interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
index 59b07a55e461..d54477b1001c 100644
--- a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
+++ b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
@@ -73,10 +73,6 @@ 
 
 	amlogic,tx-delay-ns = <4>;
 
-	snps,reset-gpio = <&gpio GPIOH_4 0>;
-	snps,reset-delays-us = <0 10000 1000000>;
-	snps,reset-active-low;
-
 	mdio {
 		compatible = "snps,dwmac-mdio";
 		#address-cells = <1>;
@@ -85,6 +81,10 @@ 
 		eth_phy0: ethernet-phy@0 {
 			/* Realtek RTL8211F (0x001cc916) */
 			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <30000>;
+			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
 		};
 	};
 };