| Message ID | 20190722185938.9043-4-linux.amoon@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Exynos USB 3.0 PHY tune setting | expand |
On Mon, 22 Jul 2019 at 20:59, Anand Moon <linux.amoon@gmail.com> wrote: > > Tune USB2.0 (UTMI+) TX signal for high speed data transfer. What is the visible effect? What does this tuning bring? > > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > --- > drivers/phy/samsung/phy-exynos5-usbdrd.c | 42 +++++++++++++++++++++--- > 1 file changed, 37 insertions(+), 5 deletions(-) > > diff --git a/drivers/phy/samsung/phy-exynos5-usbdrd.c b/drivers/phy/samsung/phy-exynos5-usbdrd.c > index 135114d51bc1..54a513ca15e4 100644 > --- a/drivers/phy/samsung/phy-exynos5-usbdrd.c > +++ b/drivers/phy/samsung/phy-exynos5-usbdrd.c > @@ -33,6 +33,8 @@ > #define EXYNOS5_FSEL_24MHZ 0x5 > #define EXYNOS5_FSEL_50MHZ 0x7 > > +#define __set(v, a, b) (((v) << (b)) & GENMASK(a, b)) > + > /* EXYNOS5: USB 3.0 DRD PHY registers */ > #define EXYNOS5_DRD_LINKSYSTEM 0x04 > > @@ -108,8 +110,17 @@ > #define EXYNOS5_DRD_PHYPARAM0 0x1c > > #define PHYPARAM0_REF_USE_PAD BIT(31) > -#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26) > -#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26) > +#define PHYPARAM0_REF_LOSLEVEL(x) __set(x, 30, 26) > +#define PHYPARAM0_TXVREFTUNE(x) __set(x, 25, 22) > +#define PHYPARAM0_TXISETUNE(x) __set(x, 21, 20) > +#define PHYPARAM0_TXRESTUNE(x) __set(x, 19, 18) > +#define PHYPARAM0_TXPREEMPPULSETUNE BIT(17) > +#define PHYPARAM0_TXPREEMPAMPTUNE(x) __set(x, 16, 15) > +#define PHYPARAM0_TXHSXVTUNE(x) __set(x, 14, 13) > +#define PHYPARAM0_TXFSLSTUNE(x) __set(x, 12, 9) > +#define PHYPARAM0_SQRXTUNE(x) __set(x, 8, 6) > +#define PHYPARAM0_OTGTUNE(x) __set(x, 5, 3) > +#define PHYPARAM0_COMPDISTUNE(x) __set(x, 2, 0) > > #define EXYNOS5_DRD_PHYPARAM1 0x20 > > @@ -365,9 +376,30 @@ static void exynos5_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd) > u32 reg; > > reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0); > - /* Set Loss-of-Signal Detector sensitivity */ > - reg &= ~PHYPARAM0_REF_LOSLEVEL_MASK; > - reg |= PHYPARAM0_REF_LOSLEVEL; > + /* Set Loss-of-Signal Detector sensitivity */ > + reg |= (PHYPARAM0_REF_USE_PAD | > + /* Sets the sensitivity level for the Loss-of-Signal detector */ > + PHYPARAM0_REF_LOSLEVEL(0x9) | > + /* Adjusts the high-speed DC level voltage */ > + PHYPARAM0_TXVREFTUNE(0x3) | > + /* Adjust the rise/fal timie of the high-speed waveform */ > + PHYPARAM0_TXISETUNE(0x1) | > + /* Adjusts the driver source impedance */ > + PHYPARAM0_TXRESTUNE(0x1) | > + /* HS Transmitter Pre-Emphasis Duration Control */ > + PHYPARAM0_TXPREEMPPULSETUNE | > + /* HS Transmitter Pre-Emphasis Current Control */ > + PHYPARAM0_TXPREEMPAMPTUNE(0x0) | > + /* Transmitter High-Speed Crossover Adjustment */ > + PHYPARAM0_TXHSXVTUNE(0x3) | > + /* FS/LS Source Impedance Adjustment */ > + PHYPARAM0_TXFSLSTUNE(0x3) | > + /* Squelch Threshold Adjustment */ > + PHYPARAM0_SQRXTUNE(0x3) | > + /* VBUS Valid Threshold Adjustment */ > + PHYPARAM0_OTGTUNE(0x6) | > + /* Disconnect Threshold Adjustment */ > + PHYPARAM0_COMPDISTUNE(0x6)); You set a bunch of parameters but I am not sure how did you get the values... Best regards, Krzysztof > writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0); > > reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1); > -- > 2.22.0 >
diff --git a/drivers/phy/samsung/phy-exynos5-usbdrd.c b/drivers/phy/samsung/phy-exynos5-usbdrd.c index 135114d51bc1..54a513ca15e4 100644 --- a/drivers/phy/samsung/phy-exynos5-usbdrd.c +++ b/drivers/phy/samsung/phy-exynos5-usbdrd.c @@ -33,6 +33,8 @@ #define EXYNOS5_FSEL_24MHZ 0x5 #define EXYNOS5_FSEL_50MHZ 0x7 +#define __set(v, a, b) (((v) << (b)) & GENMASK(a, b)) + /* EXYNOS5: USB 3.0 DRD PHY registers */ #define EXYNOS5_DRD_LINKSYSTEM 0x04 @@ -108,8 +110,17 @@ #define EXYNOS5_DRD_PHYPARAM0 0x1c #define PHYPARAM0_REF_USE_PAD BIT(31) -#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26) -#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26) +#define PHYPARAM0_REF_LOSLEVEL(x) __set(x, 30, 26) +#define PHYPARAM0_TXVREFTUNE(x) __set(x, 25, 22) +#define PHYPARAM0_TXISETUNE(x) __set(x, 21, 20) +#define PHYPARAM0_TXRESTUNE(x) __set(x, 19, 18) +#define PHYPARAM0_TXPREEMPPULSETUNE BIT(17) +#define PHYPARAM0_TXPREEMPAMPTUNE(x) __set(x, 16, 15) +#define PHYPARAM0_TXHSXVTUNE(x) __set(x, 14, 13) +#define PHYPARAM0_TXFSLSTUNE(x) __set(x, 12, 9) +#define PHYPARAM0_SQRXTUNE(x) __set(x, 8, 6) +#define PHYPARAM0_OTGTUNE(x) __set(x, 5, 3) +#define PHYPARAM0_COMPDISTUNE(x) __set(x, 2, 0) #define EXYNOS5_DRD_PHYPARAM1 0x20 @@ -365,9 +376,30 @@ static void exynos5_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd) u32 reg; reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0); - /* Set Loss-of-Signal Detector sensitivity */ - reg &= ~PHYPARAM0_REF_LOSLEVEL_MASK; - reg |= PHYPARAM0_REF_LOSLEVEL; + /* Set Loss-of-Signal Detector sensitivity */ + reg |= (PHYPARAM0_REF_USE_PAD | + /* Sets the sensitivity level for the Loss-of-Signal detector */ + PHYPARAM0_REF_LOSLEVEL(0x9) | + /* Adjusts the high-speed DC level voltage */ + PHYPARAM0_TXVREFTUNE(0x3) | + /* Adjust the rise/fal timie of the high-speed waveform */ + PHYPARAM0_TXISETUNE(0x1) | + /* Adjusts the driver source impedance */ + PHYPARAM0_TXRESTUNE(0x1) | + /* HS Transmitter Pre-Emphasis Duration Control */ + PHYPARAM0_TXPREEMPPULSETUNE | + /* HS Transmitter Pre-Emphasis Current Control */ + PHYPARAM0_TXPREEMPAMPTUNE(0x0) | + /* Transmitter High-Speed Crossover Adjustment */ + PHYPARAM0_TXHSXVTUNE(0x3) | + /* FS/LS Source Impedance Adjustment */ + PHYPARAM0_TXFSLSTUNE(0x3) | + /* Squelch Threshold Adjustment */ + PHYPARAM0_SQRXTUNE(0x3) | + /* VBUS Valid Threshold Adjustment */ + PHYPARAM0_OTGTUNE(0x6) | + /* Disconnect Threshold Adjustment */ + PHYPARAM0_COMPDISTUNE(0x6)); writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0); reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
Tune USB2.0 (UTMI+) TX signal for high speed data transfer. Signed-off-by: Anand Moon <linux.amoon@gmail.com> --- drivers/phy/samsung/phy-exynos5-usbdrd.c | 42 +++++++++++++++++++++--- 1 file changed, 37 insertions(+), 5 deletions(-)