@@ -33,122 +33,119 @@
clock-frequency = <12000000>;
};
};
+};
- ahb {
- apb {
- tcb0: timer@f8008000 {
- timer@0 {
- compatible = "atmel,tcb-timer";
- reg = <0>;
- };
+&adc0 {
+ atmel,adc-ts-wires = <4>;
+ atmel,adc-ts-pressure-threshold = <10000>;
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+};
- timer@1 {
- compatible = "atmel,tcb-timer";
- reg = <1>;
+&ebi {
+ pinctrl-0 = <&pinctrl_ebi_addr_nand
+ &pinctrl_ebi_data_0_7>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand-controller {
+ pinctrl-0 = <&pinctrl_nand_oe_we
+ &pinctrl_nand_cs
+ &pinctrl_nand_rb>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
};
- };
- mmc0: mmc@f0008000 {
- pinctrl-0 = <
- &pinctrl_board_mmc0
- &pinctrl_mmc0_slot0_clk_cmd_dat0
- &pinctrl_mmc0_slot0_dat1_3>;
- status = "okay";
- slot@0 {
- reg = <0>;
- bus-width = <4>;
- cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
+ uboot@40000 {
+ label = "u-boot";
+ reg = <0x40000 0x80000>;
};
- };
- dbgu: serial@fffff200 {
- status = "okay";
- };
+ ubootenv@c0000 {
+ label = "U-Boot Env";
+ reg = <0xc0000 0x140000>;
+ };
- usart0: serial@f801c000 {
- status = "okay";
- };
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
- i2c0: i2c@f8010000 {
- status = "okay";
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
};
+ };
+ };
+};
- adc0: adc@f804c000 {
- atmel,adc-ts-wires = <4>;
- atmel,adc-ts-pressure-threshold = <10000>;
- status = "okay";
- };
+&i2c0 {
+ status = "okay";
+};
- pinctrl@fffff400 {
- mmc0 {
- pinctrl_board_mmc0: mmc0-board {
- atmel,pins =
- <AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */
- };
- };
- };
+&mmc0 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_slot0_clk_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
+ };
+};
- watchdog@fffffe40 {
- status = "okay";
- };
+&pinctrl {
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */
};
+ };
+};
- ebi: ebi@10000000 {
- pinctrl-0 = <&pinctrl_ebi_addr_nand
- &pinctrl_ebi_data_0_7>;
- pinctrl-names = "default";
- status = "okay";
-
- nand_controller: nand-controller {
- status = "okay";
- pinctrl-0 = <&pinctrl_nand_oe_we
- &pinctrl_nand_cs
- &pinctrl_nand_rb>;
- pinctrl-names = "default";
-
- nand@3 {
- reg = <0x3 0x0 0x800000>;
- rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
- cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
- nand-bus-width = <8>;
- nand-ecc-mode = "hw";
- nand-ecc-strength = <4>;
- nand-ecc-step-size = <512>;
- nand-on-flash-bbt;
- label = "atmel_nand";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- at91bootstrap@0 {
- label = "at91bootstrap";
- reg = <0x0 0x40000>;
- };
-
- uboot@40000 {
- label = "u-boot";
- reg = <0x40000 0x80000>;
- };
-
- ubootenv@c0000 {
- label = "U-Boot Env";
- reg = <0xc0000 0x140000>;
- };
-
- kernel@200000 {
- label = "kernel";
- reg = <0x200000 0x600000>;
- };
-
- rootfs@800000 {
- label = "rootfs";
- reg = <0x800000 0x0f800000>;
- };
- };
- };
- };
- };
+&tcb0 {
+ timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>;
+ };
+
+ timer@1 {
+ compatible = "atmel,tcb-timer";
+ reg = <1>;
};
};
+
+&usart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
@@ -17,61 +17,58 @@
/ {
model = "HCE Cosino Mega 2560";
compatible = "hce,cosino_mega2560", "atmel,at91sam9x5", "atmel,at91sam9";
+};
+
+&adc0 {
+ atmel,adc-ts-wires = <4>;
+ atmel,adc-ts-pressure-threshold = <10000>;
+ status = "okay";
+};
- ahb {
- apb {
- macb0: ethernet@f802c000 {
- phy-mode = "rmii";
- status = "okay";
- };
+&macb0 {
+ phy-mode = "rmii";
+ status = "okay";
+};
- adc0: adc@f804c000 {
- atmel,adc-ts-wires = <4>;
- atmel,adc-ts-pressure-threshold = <10000>;
- status = "okay";
- };
+&mmc1 {
+ pinctrl-0 = <
+ &pinctrl_mmc1_slot0_clk_cmd_dat0
+ &pinctrl_mmc1_slot0_dat1_3>;
+ status = "okay";
- rtc@fffffeb0 {
- status = "okay";
- };
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ non-removable;
+ };
+};
- usart1: serial@f8020000 {
- status = "okay";
- };
+&rtc {
+ status = "okay";
+};
- usart2: serial@f8024000 {
- status = "okay";
- };
+&usart1 {
+ status = "okay";
+};
- usb2: gadget@f803c000 {
- atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
- status = "okay";
- };
+&usart2 {
+ status = "okay";
+};
- mmc1: mmc@f000c000 {
- pinctrl-0 = <
- &pinctrl_mmc1_slot0_clk_cmd_dat0
- &pinctrl_mmc1_slot0_dat1_3>;
- status = "okay";
- slot@0 {
- reg = <0>;
- bus-width = <4>;
- non-removable;
- };
- };
- };
+&usb0 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW */
+ &pioD 19 GPIO_ACTIVE_LOW
+ &pioD 20 GPIO_ACTIVE_LOW
+ >;
+ status = "okay";
+};
- usb0: ohci@600000 {
- status = "okay";
- num-ports = <3>;
- atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW */
- &pioD 19 GPIO_ACTIVE_LOW
- &pioD 20 GPIO_ACTIVE_LOW
- >;
- };
+&usb1 {
+ status = "okay";
+};
- usb1: ehci@700000 {
- status = "okay";
- };
- };
+&usb2 {
+ atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+ status = "okay";
};
- newline between properties and sub-nodes - use tags from included dtsi instead of duplicating the hierarchy - status should be the last property There are no differences in the generated .dtb Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> --- arch/arm/boot/dts/at91-cosino.dtsi | 203 ++++++++++----------- arch/arm/boot/dts/at91-cosino_mega2560.dts | 93 +++++----- 2 files changed, 145 insertions(+), 151 deletions(-)